Finna Sensors
Finna Sensors is fully dedicated to manufacturing continuous on-line moisture measurement and control systems as well as handheld portable moisture analyzers.
- 909-941-7776
- 909-941-6444
- 9567 Arrow Route Suite #E
Rancho Cucamonga, CA 91730
United States
-
product
Transverse HD Sawmill Meter
MC PRO 1500 HDNC
Finna Sensors built the Transverse HDNC Sawmill Meter to increase the number of potential sensors from 8 to 24. The sensors can now be specified to fit within chain runs and can be located on both the top and bottom faces. This significant increase in surface area allows mills to identify sapwood/heartwood boundary areas or wet pockets for proper sorting prior to kiln drying. Sorting by moisture content has been shown to improve drying productivity by 10% to 15%, as well as, enhance lumber recovery. Further advancements in the software allow users to track packages through the drying process, add Internet of Things (IOT) data and perform advanced analytics with new reports.
-
product
Lab Moisture Analyzer
PC-Based laboratory/production Moisture Analyzer connects through the RS-232 Serial Port. For nuts, granules, powders, pellets, chips or flakes. Complete with:– MCPC-RS Test Chamber– Windows PC-Based Software– Two Sample Cups– Dial Thermometer– Standard Block– RS-232 Cable (10 Feet)– USB to RS232 Adapter– Operating Instructions Manual– 115VAC/60HZ Wall Transformer
-
product
Model DC-2011: Cork Moisture Meter
DC-2011
Provides fast and accurate moisture read in 4% - 22% range. Durable plastic molded case, and includes Large LCD Display for easy reading. Reduces and eliminates factors such as cracked corks and poor cork compressibility, among numerous others. Product use reduces cork production error, increases efficiency, and thus increases profit.
-
product
Model DA-8: Digital Moisture Meter
552210
Provides instant moisture readings from 0% to 25% on a wide variety of materials such as gypsum board, yarn, and more. Stores up to 99 calibrations.
-
product
Model T8: Thin Materials Moisture Meter
MRC001970
Uses radio frequency capacitance to measure moisture. Provides average moisture content down to a penetration of 1/8 to 1/4 of an inch. Has three concentric rings that cover an area 3 inches in diameter
-
product
Handheld Moisture Meters
Since water has a dielectric constant considerable higher than any other material, even a small amount of water in a product will cause the combination dielectric constant to increase substantially. Finna Sensors' capacitance meters can easily recognize this increase in water content and are programmed to display the result in direct reading percent moisture content.
-
product
Model A8-AF: Radome Moisture Meter
MRC005574
Indicates the moisture pockets in aircraft radomes. Two main components include the electrode sensor and the metering unit. Critical to today's sophisticated radar transmissions as poorly monitored moisture levels can degrade radar operation.
-
product
Model L: Lumber Moisture Meter
MRC003303
Calibrated for 77 hard and soft woods in the 0% - 25% moisture range and has dials for specific woods. Accurate to 3/4" penetration. Rechargeable battery.
-
product
Model V: Veneer Moisture Meter
MRC003304
Calibrated for 48 hard and soft woods in the 0% - 25% moisture range and has dials for specific woods. Accurate to 1/8 inch penetration.
-
product
Model AM-IIIB: Paper Moisture Meter
AM-31B3
Portable digital paper moisture meter to measure single sheets. Permits instant and non-destructive moisture detection measurement on all types of paper and paperboard. Pre-programmed with 11 different Calibration Curved with option to select a field. Fast and accurate. Uses Radio Frequency to minimize effects of pH and temperature variations
-
product
Model DG-9 (Universal Voltage)
DA8-G9-UNIV
Designed for semi-solids; powdered, granular or textile materials; and pliable sheets in rolls or stacks. Optional needle electrodes and sensitivity modules which allow for a wide range of moisture measurements. Rechargeable NiMH batteries save hassle and money of battery replacement.
-
product
KilnScout-Softwood: Wireless Kiln Moisture Meter System
KilnScout-Softwood is an integrated wireless moisture system for batch and continuous kilns. The system provides real-time moisture measurements for drying optimization and control strategies. Each sensor measures 17 cubic feet providing an accurate representation of product moisture content during drying.
-
product
SMART III RF Probe
Finna Sensors’ Smart III RF Moisture Probe is appropriate in those situations where NIR use on conveying systems/web applications or RF flat plate sensor use on board type products are not sufficient. Examples include tanks, bins, barrels, drums, Super Sacks™, silos, etc. These applications require a probe type moisture meter where the probe is inserted into, and is surrounded by product. Since the probe generates a 3 inch diameter radio frequency field around the length of the probe, a significant volume of product is measured. As the product is slowly removed from the silo, and refilled from the top, it passes by the RF Probe, thereby providing a constant real time moisture measurement. Typical applications would include starches, distillers and brewers grains, granulated chemicals or food ingredients, whole grains such as corn kernels, rice, soybeans, tree nut stockpiles, etc.
-
product
Model LG: Drywall Moisture Meter
MRC006505
Provides average moisture content down to a penetration of 1in. Uses radio frequency capacitance to measure the moisture content of gypsum wallboard. 0% - 25% moisture range.
-
product
Model DC-2000-BP: Baled Paper Moisture Meter
DC-2000-BP
Portable hand-held moisture meter provides fast and accurate digital read-out in the range of 5% to 25%. Microprocessor based with large LDC display for easy reading. Pocket-size, weights less than 1lb.
