Pulsar Microwave Corporation
Pulsar Microwave Corporation, established in 1987, is a U.S.-based manufacturer specializing in high-performance RF and microwave passive components spanning DC to 85 GHz. With full in-house design and manufacturing capabilities, we maintain strict control over quality, performance, and lead times, making us a trusted partner for both standard and custom-engineered solutions.
- 973-779-6262
- 973-779-2727
- sales@pulsarmicrowave.com
- 48 Industrial West
Clifton, NJ 07012
United States of America
-
product
Voltage Controlled Phase Shifters To 3200 MHz
Pulsar's Voltage Controlled Phase shifters utilize a DC voltage to control the phase of the RF signal applied. These phase shifters utilize varactor diodes to produce the necessary phase requirements. Phase of the 180 and 360 degree designs are available, and phase can be controlled with a DC voltage 0-20 Vdc. Modulation of these phase shifters is typically 100 kHz, and maximum input power is +5 dBm.A wide variety of package styles are available, such as plug-in, flatpack, TO-cans, and connectorized housings, though the most popular are the miniature surface mount packages. Surface mount packages are available on tape and reel, for automated assembly techniques.
-
product
10-16 DB Directional Couplers From 0.5 To 50 GHz
Single directional couplers within this series operate from 0.5 MHz to 50 GHz and are available in standard values of 10, 13 and 16 dB. They fulfill narrow and broadband requirements with coupling tolerances of +/- 1 to 1.25 dB. These couplers are optimized for best matching and high directivity with flat coupling response.
-
product
Bi-Phase Modulators To 12 GHz
BPSK Modulators modulate an input signal by 0° and 180° phase shifts by injecting a ± 20 mA control signal at port D1.
-
product
Double Balanced Mixers From 0.01 To 6000 MHz
A double balanced mixer (DBM) employs the use of a well matched quad-diode ring with two balanced transformers. Because of this, a DBM enjoys the inherent advantage of high port to port isolation. The IF port in Pulsar's DBM design is DC coupled to the diodes.
-
product
2-Way Resistive Power Dividers DC To 40 GHz
Pulsar Microwave manufactures resistive dividers from DC to 40 GHz. They have a rated input power of one half watt maximum. VSWR of 1.5:1 or better maintained throughout band at all ports. Resistive dividers can be fitted with SMA male or female connectors and are available in three outline packages.
-
product
Digital Controlled Phase Shifters To 4 GHz
Pulsar's Digital Controlled Phase shifters utilize PIN diodes and delay lines to produce the necessary phase requirements. These digital phase shifters use switched lines to obtain temperature stable phase shift. The phase is specified at the center frequency ± 3.0% and is proportional to frequency over the entire band.
-
-
product
SP1T RF Pin Diode Switches To 18 GHz
Pulsar Microwave manufactures pin diode RF switches that are controlled by TTL logic. This configuration is known as single pole, single throw and is often abbreviated SPST or SP1T. They have been engineered to function in 50-ohm systems, and are designed to operate from 40 MHz to 18 GHz. They have a switching time of 100 nanoseconds and input power rating of 200 mW (23 dBm). Performance of 1.6:1 or better VSWR and minimum isolation of 60 dB is typical of most models.All switches of this type require both +5VDC and -5VDC to operate. Typical current consumption is +/- 30 mA. TTL control logic of 0 to +5VDC is required. Units comes standard with SMA connectors.
-
product
Triple Balanced Mixers From 0.05 To 4200 MHz
A triple balanced mixer uses two well matched quad-diode rings. Because of this, they offer wider LO/RF bandwidths than DBM designs. But more importantly, the TBM offers a higher dynamic range and lower distortion.
-
product
SP5T RF Pin Diode Switches To 12 GHz
Pulsar Microwave's 5-way RF switches cover bands from 300 MHz to 12 GHz in both absorptive and reflective configuration. These SP5T switches have a rating of 200 mW maximum input power and a switching time of 100 ns. They are specified with a minimum isolation of 60 dB and most models maintain a VSWR of 1.6:1 or better on all ports. The SP5T switches are driven by TTL logic control circuitry and require both positive and negative 5-volt supplies for operation. A 9-pin D-SUB connector provides the interface for the power and logic voltages.
-
product
Directional Couplers From 0.01 To 2000 MHz
Pulsar Microwave's low frequency directional couplers operate within the frequency range of 10 kHz to 2 GHz. They're available in either surface mount or connectorized designs. SMA female connectors are standard, but BNC, TNC, F, N, jack or plug are available upon request.Most of these directional couplers have a flatness of +/- 0.25 dB and directivity of 20 dB or better within the operating band. VSWR of 1.3:1 or better maintained on all ports for most models. Maximum power handling is between 1 and 3 watts depending on model.
-
product
6-Way Power Dividers From 0.4 To 22 GHz
Pulsar Microwave manufactures 6-way power dividers in connectorized packages spanning 400 MHz through 22 GHz. These narrow and broadband models are designed to operate in a 50-ohm system and are rated at 30 watts. The 6-way connectorized power dividers are available standard with wither SMA or N female connectors, though other configurations of BNC, TNC, F and male connectors are possible.
-
product
Bias Tees From 0.03 MHz To 85 GHz
Pulsar offers a large variety of bias tees that cover frequencies from DC to in both surface mount and connectorized packages. Many models are available with voltages up to 100 volts and currents up to 8 amps and custom requirements are welcomed. Options include higher voltage and current, higher RF input power and a choice of either an RF connector or a feedthrough connection for the DC input port.
-
product
6-8 DB Directional Couplers From 0.5 To 40 GHz
Pulsar Microwave manufactures the CS06 and CS08 series single directional couplers in nominal values of 6 and 8 dB, respectively. These directional couplers are used in 50-ohm systems for narrow and wideband applications within 500 MHz to 40 GHz. Standard outlines are fitted with SMA or N type female connectors, but Pulsar Microwave can customize upon request.
-
product
Low Frequency 4-Way Power Dividers To 2200 MHz
Low Frequency 4-Way Power Dividers to 2200 MHz
