Electro-Sensors, Inc.
Electro-Sensors, Inc., designs and manufactures the most reliable machine monitoring sensors and wireless/wired hazard monitoring systems in the industry.
- 1-800-328-6170
952-930-0100 - Sales@electro-sensors.com
- 6111 Blue Circle Drive
Minnetonka, MN 55343
United States of America
-
product
Tachometers
HH100
The HH100 Hand-Held Digital Tachometer combines both contact and non-contact sensing to accurately measure RPM, surface speed, and length. When using the non-contact mode, rotational speed (RPM) is measured using a visible beam of light. The HH100 can be up to 14 inches away from the small piece of reflective tape that is affixed to the rotating element.
-
product
Tilt Switch and Control Unit
MTS / SCU-200
Features • Detects the presence or absence of bulk material • Standard enclosure is NEMA 12 with indicator lights • NEMA 4 and Intrinsically Safe enclosures available • Rugged heliarc-welded steel probes • Use with SCU-200 for complete monitoring system
-
product
Pulse Generator
Traction Wheel Assembly
The complete and ready-to-install system converts linear travel/speeds to square-wave pulses/frequencies. • Square-wave frequency output, NPN open-collector • 5-28 VDC powered • 1 to 1,270 pulses per revolution (PPR - specify when ordering) • Optional bi-directional (quadrature) output models • 3 models: black neoprene rubber, smooth polyurethane, and diamond knurled aluminum tread
-
product
Closed-Loop Motor Controller
MS320
Master and Ratio-Follower modes and programmable input functions. Options include analog speed feedback input, analog setpoint inputs and relay outputs. Works with incremental shaft encoders and pulsefrequency output shaft speed sensors. Optional explosion proof enclosure or NEMA 4X enclosure kit.
-
product
Tachometers
TR5000
Features • Displays rate, time-in-process, ratio, sum, difference, or draw • Optional relay or 4-20 mA analog output • Completely field programmable • Full diagnostic functions • Setpoint and start delay functions • 3 programmable inputs • 3 programmable transistor setpoint outputs • Keypad lockout • 115, 230 VAC (50-60 Hz) and 10-30 VDC power options
-
product
Tachometers
AP1000
Features • Field programmable • Displays rates from 0-9,999 or time-in-process • Simple installation, panel mount meter • Bright 0.3 inch high efficiency LED displays • ETL approved to applicable UL and CSA standards • Standard input power is 115 VAC; 230 VAC and 12 or 24 VAC / VDC are optional.
-
product
Speed Switch
UDS1000
Features • Works with remote / external quadrature pulse frequency output sensor / incremental encoder (NPN or PNP) • DPDT relay changes state when shaft direction reverses • Reverse-over-speed setpoint adjustment from 0.5-5,000 rpm • Relay resets when reverse motion stops • 115, 230 VAC (50-60 Hz) and 12, 24 VDC power options • Explosion proof/NEMA 4X housing • UL Listed Class I, Div I (C, D) Class II, Div I (E, F, G)
-
product
Speed Switch
LRB1000/LRB2000
Features• Works with remote/external pulse frequency output sensor (NPN, PNP)• Over- or under-speed 1-1,000 rpm• 1 SPDT relay output (LRB1000) or 2 SPDT relay outputs (LRB2000)• Visual setpoint adjustment with digital accuracy• Dial-in calibration does not require power• Built-in start delay• DIN rail mounting simplifies installation• 115, 230 VAC (50-60 Hz) and 12, 24 VDC power options
-
product
Wired Hazard Monitoring
Grain dust is extremely volatile and can easily explode with the proper ignition source in confined spaces. OSHA has mandated that grain elevators in Class II, Division 1 environments must have the 3 monitoring sub-systems for elevator safety (1910.272(q)(4)(ii), 1910.272(q)(5), 1910.272(q)(5)).
-
product
Heavy Duty Vibration Monitor
VUM-800
Features • Heavy-duty sensing probe • DPDT 10 amp relay • Optional 230 VAC operation • Control unit remotely mounted • Failsafe operation
-
product
Proximity Sensors
600 Series
600 Series Proximity Sensors are active digital sensing devices that generate one pulse per pass of an actuating target within their sensing field. No direct contact with target material is necessary. Each sensor is entirely solid state with no moving parts to wear out.
-
product
Speed Switch
M100T/M5000T
Features• Internal sensor• SPDT relay output• 5-100 rpm (M100T), 100-5,000 rpm (M5000T)• Terminal block for easy wiring• 115, 230 VAC (50-60 Hz) and 12, 24 VDC power options• Works with Electro-Sensors magnetic pulser discs/wraps• Explosion proof (XP) housing• UL Listed Class I, Div I (C, D) Class II (E, F, G)
-
product
Hall Effect Sensor
907 XP (Explosion Proof)
Features • NPN open collector, square-wave output • Zero speed operation with no signal loss • Non-contact, large gap distance sensing • Signal transmits up to 1,500 ft • Simple to install and set up • Powered by 5-24 VDC • Class I, Div I (D) Class II, Div I (E, F, G) Class III • XLB-3 enclosure • Bi-directional option (907B XP)
-
product
Motor Drive Control
Four motor speed drive control models ranging from a simple speed dial/display to complex machine/process synchronizers. Capable of many motor/machine control schemes, from open-loop master to closed-loop pulse-locked speed/event synchronized follower. Compatible with all motor speed drives of any size/power rating with an analog input (AC, AC Vector, DC and Servo)
-
product
Pulse Generator
Digital Ring Kits
NEMA C frame rings provide mounting for 1101, 1201, and 1202 shaft speed sensors for use with 199SM magnet wheels on motors with NEMA C frames. The DRK (Digital Ring Kit) Series provides a single-channel output and the QDRK (Quadrature Digital Ring Kit) Series offers a bi-directional output. Kits include mounting ring, hardware, magnet wheel, and sensor.
