Motion Simulators
-
product
Real-time RF Channels Simulator
RF-LiveSim
Covering a frequency range from 50 to 900 MHz, RF Live Simulator can emulate RF channels propagation modes in real-time for a signal bandwidth from 20 kHz to 20 MHz (gaussian noise, multipath, Doppler and frequency drift tools). RF-LiveSim is a cost effective solution for intense automatic non regression tests at the physical layer level. RF-LiveSim includes 1x RF input and 1x RF output ports, and provides a complete set of channel models, either for fixed or mobile propagation environments. Whatever the standard, any type of receiver can be tested. Thanks to its real-time process, from your basic original signal, RF-LiveSim can perform, for instance, efficient regression testing of LTE solutions to check the good behavior and the limits of your receiver when multipathes, Doppler and Gaussian noise are applied.
-
product
PXI Battery Simulator Module, 4-Channel, 5 Amp
41-754-011
The 41-754-011 and 43-754-011 are 4 channel battery simulators, capable of supplying up to 8 V and 5 A per channel. The channels are fully isolated from ground and from each other allowing series connection to simulate batteries in a stacked architecture. The isolation barrier (1000 V channel to GND and 750 V channel to channel) allows the module to be used as a battery stack representative of those used for vehicle propulsion..
-
product
6 Channel Function Generator / Flow Simulator
DP-cPCI-2601
DP-cPCI-2601 is a 6 Channel 2MS/s Waveform Generator with high frequency performance, versatility and compact size in an economical cPCI bus format. Signal output in the range of 10 mHz to 5 KHz with 14 bit vertical resolution makes this single slot, 6U-sized cPCI card a powerful solution to meet most demanding test stimulus.DP-cPCI-2601 uses Direct Digital Synthesis (DDS) technique to generate stable and accurate output waveforms down to 0.01 Hz resolution. DP-cPCI-2601 offers Sine, Square, Ramp, Triangle, Pulse as built-in wave shapes and user defined arbitrary waveform.DP-cPCI-2601 can frequency sweep any of its function outputs. User can sweep upwards using linear sweeps.
-
product
MIL-STD-1553 A / B Test And Simulation PC / 104+ Module
PC104p-1553
*Dual redundant*1, 2, 4 or 8 channels*Simultaneous bus controller, 31 remote terminals, bus monitor*Error entry and detection*FPGA based hardware architecture*Multi-level trigger for data acquisition and filtering*10 programmable, discrete I / O*IRIG-B timecode encoder / decoder with free-running mode*Real-time recording and physical bus playback*Supports: C, C ++, C # and .net*Driver support: Windows, Linux, LabView Real-Time and other systems*Supports ARINC429 and ARINC 664 operations
-
product
Time-domain Field-Device-Circuit coupled simulator
EM-SUPREME®
Time-domain Field-Device-Circuit coupled simulator for modeling of passive structures, active components, and complete RF & millimeter-wave modules. EM-Supreme is used for EM modeling of power amplifiers, switches, filters, active antennas, and complete RF modules such as antenna-switch, switch-filter, switch-filter-amplifier, and front-end modules with no approximations.
-
product
Simulation Tools for Analog and Power Electronics
SIMetrix
Complete mixed-mode simulation package providing high performance, ease of use and superior analog convergence.
-
product
Environmental Simulation Testing
MET's Environmental Simulation Labs, on both coasts, employ numerous environmental chambers, including several large walk-in chambers. Hydraulic and electro-dynamic shakers are used for a wide range of vibration testing, from ISTA packaging to seismic compliance testing. MET's hydraulic vibration systems are capable of full level (Zone 4) seismic simulation.
-
product
MIMIC® Simulator Suite
MIMIC Simulator creates a real world lab environment, with 100,000 devices, at a fraction of the cost of physical equipment. It provides an interactive hands-on lab for quality assurance, development, sales presentation, evaluation, deployment and training of enterprise management applications. Users create a customizable virtual environment populated with simulated routers, hubs, switches, WiFi/WiMAX/LTE devices, probes, cable modems, servers and workstations.
-
product
Seat Motion
Astronics PGA is a long time supplier of the cabin interior market. All Carat® Motion Systems are optimized for efficient energy use, easy integration, and ease of operation. Explore all product ranges to find the right Carat Motion System for your projects.
-
product
PXI Single 8 Channel Switch Simulator
40-485-021
Designed to simulate the operation of automotive switches where dirty contacts or leaking current can be expected from switch contamination. It allows automotive I/O devices to be tested for correct operation under adverse conditions.
-
product
Network Simulation Platform
OMNeT++
OMNeT++ is an extensible, modular, component-based C++ simulation library and framework, primarily for building network simulators. “Network” is meant in a broader sense that includes wired and wireless communication networks, on-chip networks, queueing networks, and so on. Domain-specific functionality such as support for sensor networks, wireless ad-hoc networks, Internet protocols, performance modeling, photonic networks, etc., is provided by model frameworks, developed as independent projects. OMNeT++ offers an Eclipse-based IDE, a graphical runtime environment, and a host of other tools.
-
product
Direct Drive Motors And Motion Systems
HEIDENHAIN offers the largest direct drive motor range on the market via ETEL. Solutions range from high-end motion systems with nanometer precision to industrial applications requiring high torque. And like HEIDENHAIN, ETEL builds its linear and torque motors, along with motion systems, on a foundation of superior knowledge and technical expertise, disruptive technology and tireless quality control. Customers reap the benefit: the most cutting-edge, reliable and precise motion control solutions available.
-
product
Plastics Simulation Software
Moldex3D
Moldex3D is the world leading CAE product for the plastics injection molding industry. With the best-in-class analysis technology, Moldex3D can help you simulate the widest application range of injection molding processes to optimize product design and manufacturability, shorten time-to-market, and maximize product ROI.
-
product
Single, Dual or Quad Stream MIL-STD-1553A/B Test and Simulation Module
APE1553-x
MIL-STD-1553 Test and Simulation Module for PCI Express with 1, 2 or 4 Dual Redundant channels (APE1553-1, APE1553-2, APE1553-4) plus 8 programmable discrete Input/Output channels. A unique feature of AIM’s APE1553-x module is the option for the MILScope™ capability. Models APE1553-1-DS/APE1553-2-DS integrate an onboard Analogue to Digital Converter (ADC) which samples, measures and stores the MIL-STD-1553 waveform. Automatic waveform validation is performed by the users Application Software or in conjunction with AIM’s PBA.pro Databus Test and Analysis Software and Test Scripts.
-
product
Protocol Simulation
Message automation and protocol simulation test tool that supports simulation of a variety of protocols (VoIP/IP, TDM, Analog, Wireless) all within a single framework. The application includes various test plans and test cases to support the testing of real-time entities
-
product
Finite Element Method Magnetics Simulation Software
FEMM
Finite Element Method Magnetics
FEMM is a suite of programs for solving low frequency electro magnetic problems on two-dimensional planar and axisymmetric domains. The program currently addresses linear/nonlinear magneto-static problems, linear/nonlinear time harmonic magnetic problems, linear electrostatic problems, and steady-state heat flow problems.
-
product
Test & Simulation Interface for PCI-X
PCI-X-C1760
Avionics Interface Technologies
HS1760/MIL-STD-1760E Test & Simulation Interface for PCI-X
-
product
Date & Time Simulation Software
TimeShiftX
TimeShiftX is a date and time simulation software that lets you time travel software into the future or past for temporal testing all date and time sensitive functionality and code such as end of year/month, daylight savings, leap year, billing, rates, policies, etc. Perform time travel testing instantly, without any code changes, manual work, or server isolation
-
product
MIL-STD-1553 USB & LAN Test & Simulation Module
UXI-1553
Avionics Interface Technologies
Dual redundant, single, dual, or quad stream configurationsConcurrent BC, 31 RTs, and BM operations - Physical Bus ReplayFull error injection/detection capabilities - Programmable trigger and capture - Programmable Bus Coupling and Output Voltage Levels - Onboard IRIG-B time code encoder/decoder for Synchronization - Time Synchronization to IEEE 1588 via Ethernet LAN port - 10 Discrete I/O Interfaces (5 Outputs / 5 Inputs) - Operates from a single USB or Ethernet LAN connection - Supports SAE AS4112/4114 protocol testing requirements- Flight Simulyzer™ GUI Analyzer software
-
product
Cyber Crisis Simulator
When responding to a cyber crisis, the C-Suite no longer works in a silo. Executive management continuously collaborates with incident response and SOC teams to make well-informed decisions. But tabletop exercises and conventional crisis simulation platforms do not prepare for this new reality.
-
product
Computer simulators
There are three computer simulators offered by INFRAMET:*SIMTERM - computer simulator of thermal imagers,*VIRTEST - computer simulator of test proces thermal imagers ( MRTD measurement)*NIGHTMET - computer simulator of image intensifier tubes
-
product
Single-Output Software-Defined GNSS Simulator
BroadSim Solo
Designed to address the permanent challenges that engineers face with laboratory capacity and availability, BroadSim Solo was developed to bring advanced GNSS scenario creation to your desk and propel development cycles.
-
product
Central Office Line Simulator
AI-7280
The AI-7280 is a highly flexible central office line simulator. It is designed primarily for the testing and verification of common terminal equipment, including standard telephones, Caller ID devices, SMS (Short Message Service) capable equipment, and any device using an analog Tip/Ring interface circuit. Supplied with the TRsSim software for Windows, it can analyze a telephone''s DTMF characteristics, pulse dialing and flash timing, generate various network tones and ringing patterns. Both Type I (on-hook) and Type II (off-hook) Caller ID is supported using either FSK or DTMF data transmission. As an optional component, the TRsSim software can perform SMS testing to either the ETSI protocol 1 or protocol 2 standards.
-
product
PXI Analog Output/Current Loop Simulator Module - 8 Channel
41-765-003
The 41/43-765-003 is an 8-channel Analog Output Module designed to meet the requirements of industrial control applications utilizing current loops 4 – 20mA. It consists of up to four 16-bit, digital-to-analogue converters (DAC), capable of creating four current outputs each. Output current within 0mA - 4mA and 20mA - 24mA, give the ability to simulate error or extra signaling conditions. The ±24mA mode gives the ability to simulate either sourcing or sinking sensor.
-
product
Modular Solar Array Simulator Mainframe, 1200W
E4360A
The Keysight 1200W, E4360A Modular Solar Array Simulator is a 2U high, 2-slot mainframe that accepts up to 2 E4360 series modules. Modules are ordered separately. It offers LAN, USB, and GPIB interfaces standard.
-
product
Gyro Simulator for Aircraft or Bench Use
TA-256A
This is a transformer isolated gyro simulator that can substitute for the KI256 attitude indicator and thus eliminate the requirement to remove that gyro to a remote stand and route a vacuum or pressure source out to the aircraft.
-
product
PXI/PXIe Battery Simulator Module, 2-Channel, V/I Readback, Simplified Current Sink, 750 V Isolation
43-752A-913
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 2-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
product
WAN Simulator / Emulator
LANforge ICE
LANforge ICE emulates networks that involve limited bandwidth, latency, packet loss, and corruption. LANforge ICE tests the behaviour of devices that sit on either side of an impaired network. Reduces lab and training costs by replacing expensive WAN hardware, such as T1 and FrameRelay devices. Automates testing with various scripting features and libraries.
-
product
EFT/Burst Simulators
Suzhou 3ctest Electronic Co.,Ltd.
High-end test instrument of EFT/Burst for new energy, which fully comply with CE and CCC certification. With a built-in three-phase five-wire automatic coupling /decoupling network EFTN 69100T, it can meet the requirements of new energy test system and high power load test. It is featured with good reliability, stable performance and easy use.
-
product
Modular DC Electronic Load LED Simulator
6310/A
Chroma Systems Solutions, Inc.
Chroma 6310A Programmable Electronic Load integrates microprocessor capabilities into each load module and mainframe to provide simple and accurate parallel operation to optimize the speed and control among multiple load modules. All load modules may be configured to work synchronously, to test multiple outputs simultaneously, thus simulating real life applications.
