Motion Simulation
-
Product
PXI Battery Simulator Modules
-
These PXI battery simulators are designed to simulate the power supplies of portable battery powered equipment and the single cell (model 41-753) is particularly suitable for cell phone testing. These modules can source current to simulate a battery supply or sink current to simulate a battery under charge.
-
Product
Time-domain Field-Device-Circuit coupled simulator
EM-SUPREME®
-
Time-domain Field-Device-Circuit coupled simulator for modeling of passive structures, active components, and complete RF & millimeter-wave modules. EM-Supreme is used for EM modeling of power amplifiers, switches, filters, active antennas, and complete RF modules such as antenna-switch, switch-filter, switch-filter-amplifier, and front-end modules with no approximations.
-
Product
Emulate Test in simulation
STIL-VT
-
Emulate test patterns in simulation environment with DUT simulation model. The simulation allows pre-silicon debug of test patterns. Reads the intermediate STIL format of tester patterns and creates a Verilog /VHDL simulation test bench. (A sub-set of Virtual tester solution)
-
Product
Solar Simulator
-
Excellent reputation for its high degree of throughput, accuracy and stability. Pulsed light is used, ensuring stable measurement.Approximates the spectral distribution of AM 1.5G reference solar radiation. Achieves accurate measurement of various modules.No need to reverse modules, facilitating in-line operation.
-
Product
PMC Module With 2 Or 4 CAN Bus Nodes ARINC825 Compliant For Testing & Simulation Of Avionic CAN Bus Systems
AMC825-x
PMC Module
ARINC825 (CAN bus) Test & Simulation module for PMC with 2 or 4 electrically isolated CAN bus nodes operating concurrently at CAN bus high speed bit rate of up to 1Mbit/s. The AMC825-x PCI Mezzanine Card (PMC) can work either with full functionality as an active CAN node for testing and simulating or in Listening Only mode for monitoring and recording purposes.
-
Product
Solar Array Simulator DC Power Supply
62000H-S
-
Chroma Systems Solutions, Inc.
Solar Array Simulator DC Power Supplies by Chroma provide programmable simulation of Voc (open circuit voltage) up to 1800V and Isc (short circuit current) up to 30A. The 62000S-H series provides an industry leading power density in a small 3U high package. The Solar Array Simulator is highly stable and has a fast transient response design, which are both advantages to MPPT performance evaluation on PV inverter devices.
-
Product
Load Cell Simulators / Testers
-
A load cell simulator is a handy tool during initial setup, particularly of a batching by weight scale. It replaces the load cell(s) in the system allowing the scale technician to simulate various weights that will trigger the outputs setpoints for activating valves, gates, and mixers. These products are a must for anyone involved in scale installations and repairs.
-
Product
Production Caller ID Signal Simulator
AI-80
-
The AI-80 is a fully programmable stand alone Caller ID signal generator designed for production environments. It is capable of generating signals for all FSK and DTMF based Caller ID standards. Includes general telephone signal analysis features and a highly flexible programming language for sophisticated and complex production testing sequences.
-
Product
Single Or Dual Stream MIL-STD-1553A/BTest And Simulation Module For Standard Ethernet
ANET1553-x
-
The ANET1553-x is a member of AIM’s new line of Ethernet based modules for analysing, simulating, monitoring and testing MIL-STD-1553A/B databuses. For wireless applications, an ANET compatible USB Wifi dongle is optionally available. The capability to execute Python scripts in the ANET is a standard feature. For applications with multiple ANET devices AIM offers the ADock ANET Docking Station to host up to 4 ANET modules.
-
Product
Economic 4-Axis Motion Control Universal PCI Express Card
PCIE-1245E
-
Encoder input is 5 MHz for CW/CCW,P/D,AB modePulse output up to 5 MHzMemory buffer (10 K points) for trajectory planningPoint-to-point, line and E-GearHardware emergency input
-
Product
Test & Simulation Interface for PCI Express
PCIe-C1760
-
Avionics Interface Technologies
HS1760/MIL-STD-1760E Test & Simulation Interface for PCI Express
-
Product
PC-Based Motion Control Boards
-
ICP DAS USA has developed PC-based solutions for machine automation applications, including: PCI bus motion control cards and the ISA bus motion control cards series. ICP DAS USA also offers a wide range of quick-connect terminal blocks for a range of servo motors, including Mitsubishi, Panasonic, Yaskawa, Delta, etc., which helps customers quickly implement the installation and reduce the potential for using the incorrect wiring.
-
Product
MIL-STD-1553 A / B Test And Simulation USB Module
USB-1553
-
*Dual redundant*1 or 2 channels*Simultaneous bus controller, 31 remote terminals, bus monitor*Error entry and detection*FPGA based hardware architecture*More programmable triggers and acquisition*10 programmable I / O*Onboard IRIG-B timecode encoder / decoder*Supports stand-alone operation via USB connection, without external power supply*On-board battery for runtime without power supply
-
Product
ARINC 429 Test & Simulation Interface for PCI Express
PCIe-C429
-
Avionics Interface Technologies
4, 8, 16, or 32 Software Programmable Tx/Rx Channels - Programmable High/Low Speed Operation - Concurrent operation of all Tx/Rx Channels at high data rates - Full error injection and detection • Data capture filtering, 100% bus recording, and physical bus replay - Rate-oriented Label Transmission - Label Selective Trigger for Capture/Filtering - IRIG-B time code encoder/decoder with free-wheeling mode - Application Interface supporting C/C++, C# and VB.NET Development - Device driver support: Windows, Linux, LabVIEW Real-Time (others on request) - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
Product
Multi-Parameter Patient Simulator
-
A portable, modular device used to test and calibrate patient monitors.
-
Product
Simulation & Analysis Solution for Automotive Audio Networks
A2B Analyzer System
-
The A2B Analyzer System is designed specifically for development teams servicing automotive OEMs, Tier 1s, and audio connectivity equipment suppliers. The deterministic nature of the A2B technology makes it particularly well-suited for automotive audio devices (active speakers, microphones) and newer applications such as ANC. The A2B Analyzer System consists of a compact hardware device, an accompanying software development kit (SDK), and network configuration and simulation tools.. The hardware device includes a USB 2.0 interface for PC connectivity for audio data and command/control functions. The small form factor device also features a variety of popular audio and connectivity peripherals.
-
Product
Circuit Breaker & Control Cabinet Simulator
SIM-CB6
-
The SIM-CB6 is the circuit breaker simulator that will make you an expert in breaker testing. The SIM-CB6 enables you to simulate any type of circuit breaker (SF6, Air Blast, Oil, etc.) up to 6 contacts (2 contacts per phase), with or without closing/opening resistor contacts and control cabinets. This simulator will allow you to increase your knowledge on circuit breaker analyzer systems to ensure full efficiency once on the field.
-
Product
Acceleration Simulation Mode (ASM) for Single Driven Axle Vehicles
ASM_AF | VP 230045
-
Maschinenbau Haldenwang GmbH & Co. KG.
The ASM-AF roller set is used in test centres and is suitable for vehicles with a single driven axle. It was designed for the exact measurement of the exhaust gas behaviour of vehicles during their transient emission test and permits a driving resistance simulation for the exhaust gas tests ASM-5015 and ASM-2525 (Acceleration Simulation Mode) in accordance with the specifications BAR '97. The ASM-AF is built into the base.
-
Product
Advanced 2-Axis Servo & Stepper Motion Controller
PCI-8102
Motion Controller
PCI-8102 is an advanced stepper/servo motion controller to meet high performance/cost ratio request. Compared with PCI-8132/PCI-8134, PCI-8102 mainly offers three features: Software security check for users' software, card ID setting and circular interpolation control. Besides, PCI-8102 also provides users many additional features with cost-effective way. For details, please refer to the user manual.
-
Product
Acceleration Simulation Mode (ASM)
-
Maschinenbau Haldenwang GmbH & Co. KG.
MAHA Acceleration Simulation Mode (ASM) Products
-
Product
Field Simulation Software
QuickField™
-
QuickField™ is a very efficient Finite Element Analysis package for electromagnetic, thermal, and stress design simulation with coupled multi-field analysis.
-
Product
Motion ASIC
-
Designed by Motion ASIC and offers high-performance and fast control response to meet a wide range of advanced motion control features
-
Product
Patterning Simulation
-
KLA’s patterning simulation systems use advanced models to explore critical-feature designs, manufacturability and process-limited yield of proposed lithography and patterning technologies. Our patterning simulation software allows researchers to evaluate advanced patterning technologies, such as EUV lithography and multiple patterning techniques, without the time and expense of printing hundreds of test wafers using experimental materials and prototype process equipment.
-
Product
Synchro/Resolver Conversion & Simulation PMC boards
-
Versatile, rugged, and time saving Synchro/Resolver conversion and simulation PMC boards featuring multiple high accuracy, independent channels and easy programmability, to provide a highly accurate and convenient method to test and simulate positioning systems in lab and embedded environments. The SB-3642 conversion and SB-3644 simulation boards’ versatility and ruggedness enable them to be used first in the lab, and then be readily designed into embedded applications, just by the switch of a carrier card.
-
Product
Acceleration Simulation Mode (ASM) Roller Set
ASM-P | VP 230046
-
Maschinenbau Haldenwang GmbH & Co. KG.
The ASM-P roller set is used in test centres and is suitable for vehicles with a single driven axle. It was designed for the exact measurement of the exhaust gas behaviour of vehicles during their transient emission test and permits a driving resistance simulation for the exhaust gas tests ASM-5015 and ASM-2525 (Acceleration Simulation Mode) in accordance with the specifications BAR '97. The increased tractive force of its eddy current brake means that the ASM-P is also suitable for power measurements at constant speed and constant tractive force.
-
Product
STANAG3910 Electrica lTest And Simulation Modulefor Standard Ethernet
ANET3910-EN
-
STANAG3910 Electrical Test and Simulation module for Standard Ethernet. The ANET embedded Linux operating system gives the unique capability to run the optional PBA.pro Engine right in the box.Another option is the ANET-ADK onboard software development kit where users create run-time applications to execute right in the box. For wireless applications, an ANET compatible USB Wifi dongle is optionally available. The capability to execute Python scripts in the ANET is a standard feature. For applications with multiple ANET devices AIM offers the ADock ANET Docking Station to host up to 4 ANET modules.
-
Product
Gyro Simulator for Aircraft or Bench Use
TA-256A
-
This is a transformer isolated gyro simulator that can substitute for the KI256 attitude indicator and thus eliminate the requirement to remove that gyro to a remote stand and route a vacuum or pressure source out to the aircraft.
-
Product
Cost-Effective Network Simulator
Emutel Maestro
-
Emutel Maestro brings you the perfect solution for testing your DSL equipment. Connect to your product while still in your own testing lab and perform those final tests in a real environment, enabling you to identify and solve any problems before they occur on site.
-
Product
NIBP Simulator
SC-4 SimCube®
-
The SimCube SC-4 provides all the necessary parameters for testing the basic features of a patient monitor including 3 NIBP simulations, ECG, Heart Rate Sequence, Respiration, Digital Manometer, and Peak Detect Test modes with the option to upgrade to include the OxSim SpO2 simulator and complete accessory kit. Features one-button operation for quick testing of patient monitors.
-
Product
Fibre Channel PXI Express Test & Simulation Instrument
PXIe-FC4
-
Avionics Interface Technologies
3U PXIe form factor will fit into any PXIe or hybrid slot - Supports Point-to-Point, Switched Fabric, and Arbitrated Loop topologies - Two independent Fibre Channel ports - Two SFP sockets accept fiber or copper transceivers - Each port supports 1, 2, and 4 Gbps speeds - Comprehensive decoding of FC-1, FC-2, and Upper Layer Protocol (ULP) frames - Triggering and Filtering - Error Injection on any Header or Payload Parameter - Data Capture to on-board memory or disk file - Live Capture and Current Value Monitoring - IRIG-B Time Code Encoder/Decoder for Data Correlation - In-line Port Configuration for Transparent Analyzer - Supports multiple ULPs including FC-AE-ASM, FC-AE-RDMA, FC-AE-1553, and FC-AV - Supports HS-1760E applications, including AS5653, AS5625, and AS5627fcXplorer Windows-based FC Simulator and Analyzer Test Software
