-
Product
Digital And Mixed Signal Oscilloscope
MSO/DPO70000 Series
-
The MSO/DPO70000 is one of the most advanced oscilloscopes in its class: enabling today’s engineer to see signals better with minimal noise, debug signal anomalies faster, reduce debug time, and utilize measurement and analysis tools for automated compliance testing and other verifications. In addition, the MSO/DPO70000 is perfect for analog/digital design and debug, data communications and high-speed serial communications. See how you can use the MSO/DPO70000 for your next project to find and analyze a wide range of mixed-signal anomalies.
-
Product
SoC Verification
TrekSoC
-
TrekSoC automatically generates self-verifying C test cases to run on the embedded processors in SoCs. This verifies your chips more quickly and more thoroughly than an external testbench, hand-written C tests, or running only production code on the processors. TrekSoC's generated test cases target all aspects of full-SoC verification and work in a variety of different environments.
-
Product
PCI Programmable Resistor Card 4-Channel 2 Ohm To 127 Ohm - SPST
50-294-112
-
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Resistivity Meters
-
Periodic compliance checks of ESD work surfaces are super important. Monitors only verify the ground plane, or path to ground. The surface itself can wear down, become dirty, or if you use low quality mat—just not hold up. A handheld Surface Meter is great for running monthly, or prescriptive compliance verification of your ESD surfaces.
-
Product
PXI Resistor Module 4-Channel 1R to 255R
40-293-013
-
The 40-293 is a Programmable Resistor module with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Frequency Converter
FC5-29M
-
Frequency converter FC5-29M is a measurement instrument which is designed for spectrum conversion of 75 - 170 GHz to 1 MHz ÷ 2,6 GHz range and automatic frequency measurement of sinusoidal signals. When combined with the 1 MHz - 3,0 GHz spectrum analyzer, FC5-29M can be used for examination of the continuous and periodically repeating pulse signals.The instrument is meant to be used for measurement of various signal sources, radio-transmitting instruments, synthesizers, frequency converters, measurement generators and also for adjustment and verification of various radio-transmitting or communication instruments in laboratory and workshop conditions.
-
Product
Wideband Active Load Pull
S94572B
-
The software enables power amplifier distortion measurements under varying load conditions that are controlled across the entire modulation bandwidth. When design verification and robustness evaluation require testing the device away from the optimum loading condition, this application provides powerful insight into device performance and degradation.
-
Product
Verification And Print Quality Inspection Solutions
-
Integrate quality barcode verifiers within your production line using our robust barcode verification technology.
-
Product
Test Solution Offering BER Testing
Eye-BERT Micro LR
-
The Eye-BERT Micro LR is a low cost, easy to use test solution offering BER testing at any rate between 6.312 and 125Mbps on either optical or electrical interfaces. Features include: continuously variable bit rate, user programmable pulse generator, internal CDR with retimer mode, bit rate measurement, and recovered clock output. The Unit is supplied with anti-skid bumpers for bench use, and is small enough to be integrated into larger systems for dedicated link verification.
-
Product
100 High Speed Programmer
Commander Accelerator
-
The Commander High Speed Programmer (HSP) is low overhead system designed to test Flash Memories, PLA's and Micro-controllers. The parallel multi-module architecture provides the flexibility to program and test multiple devices. It's full-featured capabilities support chip erasing and programming, sector erasing and programming, sector protect and unprotect, and data verification functions.
-
Product
Digital Video Generator and Tester
DLT710
-
Artel’s DLT710 Digital Video Generator and Tester is an innovative, DigiLink based solution for simple, automatic link verification of serial digital video formats. Functioning as both a signal generator and test monitor for 3G-SDI, HD-SDI, SD-SDI, DVB-ASI, and ATSC, the DLT710 is ideal for automatic verification of single or multi-format video links.
-
Product
System for the Analysis of 10/25/40/50/100Gbps Ethernet and Gen 6 (32GFC) Fibre Channel
SierraNet T328
-
The SierraNet T328 system provides for analysis of 10/25/40/50/100Gbps Ethernet and Gen 6 (32GFC) Fibre Channel data capture and protocol verification for developers & protocol test engineers in LAN, SAN, NAS and other Ethernet and Fibre Channel applications. Available with eight SFP28 FlexPorts™ for maximum configuration and utility, the SierraNet T328 includes an easy to use, customizable software interface, large capture buffers, and the most advanced T.A.P4 capture, triggering and filtering capabilities in the industry.
-
Product
Network Surveillance System
-
The network backbone contains a wealth of information that can be monitored and collected to support diagnostic, troubleshooting, and fraud prevention activities. Surveillance of network characteristics is becoming more important than ever before. Few important aspects of network surveillance include, Performance Monitoring, Security, Fraud Prevention, Physical Layer monitoring, Billing Verification, Remote Protocol Analysis, Failure Prediction, Traffic Engineering, Call Quality Monitoring and Troubleshooting.
-
Product
Portable Bar Code Verifier
Inspector 5000 Auto Optic
-
The Inspector 5000 Auto Optic provides ISO 15416 and ANSI X3.182 Method. This unique portable bar code verifier can interface with either the patented RJS Auto-Optic scan head or a laser scanner. Store and print capability, multiple scan averaging and subsymbology choices are easily accessed through a simple seven-button user interface with a large color LCD display. The scanners are easily installed by the user, which makes the unit quickly adaptable to practically any verification requirement.
-
Product
PCI Resistor Card 2-Channel 2 Ohm To 16.3k Ohm
50-293-031
-
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Signal Generator
G4-1XXM
-
The G4-1XXM series Signal Generator is general-purpose source for testing and verification of microwave equipment in industrial and laboratory conditions. The instrument provides high accuracy millimeter-wave signal level in wide attenuation range and can be integrated in manual or automatic measurement systems.
-
Product
Regenerative Grid Simulator
61800 series
-
Market demand for Distributed Resource (DR) products such as PV inverters and wind energy systems is steadily growing as the world strives for clean renewable energy sources. This demand has created a need for rigorous regulation testing to standards such IEEE 1547 / IEC 61000-3-15 / IEC 62116 ensuring proper and safe operation of on-grid products. It has become critical to manufacturers to conduct these tests to prove compliance and to relieve product liability concerns. Chroma’s new 61800 family of Grid Simulators has been designed to fulfill these test requirements by providing a full 4 quadrant, fully regenerative, grid simulator with advanced features for compliance, safety and product verification testing.
-
Product
Mode-Conditioned Light Sources
-
Thorlabs' Mode-Conditioned Light Sources are fiber-coupled LED sources that have an output with a flat-top profile in the far field. Common applications include the testing of multimode fused fiber components as well as verification of modal behavior in fiber-based setups. Standard fiber-coupled LED sources can have a range of output profiles that are usually not uniform and vary from source to source. This can be dependent on emitter orientation, alignment with fiber tip, and connector assembly. These mode-conditioned sources have been engineered to distribute light evenly into all transverse modes, resulting in an equilibrium modal distribution at the output. The front panel includes an adjustment knob to control the power and an output port that accepts 2.2 mm wide-key FC/PC connectors. A DS15 15 V power supply with a location-specific plug is included with each device.
-
Product
HBM Verification Tester
HBM-VT
-
High Power Pulse Instruments GmbH
- HBM pulse generator verification tester according ANSI/ESDA/JEDEC JS-001 up to ±10kV- To be used in HBM test and qualification labs for regular pulse generator specification compliance test in order to fulfill lab audit and certification requirements- Fully automatic compliance test and verification of HBM pulse generators regarding ANSI/ESDA/JEDEC JS-001 normative standard at 3 different load conditions: Short Circuit, 500 Ω, and a reference diode at VBR=15 V reverse breakdown voltage, including DC test- Parameter evaluation and verification of the transient HBM current waveforms: Peak Current, Rise Time, Decay Time, Maximum Ringing Current- Optionally available upgrade for all HPPI TLP-3010C, 4010C, 8010A, 8010C, HBM-TS10-A hardware systems in combination with HBM-S1-B (6kV) pulse generators (upgrade on request)- Fully automatic test report generation (PDF)- Electrically floating (no fixed system ground): The HBM loads, current sensor output, USB control interface and the enclosure are electrically floating. There is no limiting system ground which may introduce common-mode interference induced HBM current measurement errors.- Isolated industrial full-speed USB control interface- Isolated power supply derived from USB port- Compact size 126mm x 82.5mm x 44.5mm
-
Product
Cross Sections and Metallography
-
Rocky Mountain Laboratories, Inc.
Cross sections are prepared by mounting samples in epoxy and then grinding and polishing the mount for imaging in the optical microscope or Scanning Electron Microscopy (SEM). Valuable information from cross sectioning can include: film thicknesses, inclusions, corrosion thickness, dimensional verification, and subsurface defects. Metallographic cross sections are typically etched to reveal the microstructure. Microstructural analysis can provide information about heat treatment history, corrosion susceptibility, as well as undesirable microconstituents.
-
Product
Measurement and Analytics Solutions
-
Based on our OTP² system platform, we were able to implement a family of scalable test systems which is based on a common systems architecture, e. g. for products in the area of chemical analytics measurement. We not only implemented a universal, extremely comprehensive test system, but also a series of compact systems for benchtop placement which are fully compatible with the larger, universal system. Our specialized self-test adapters and test software enable fast verification of the test systems as well as partly automated calibration by the customer.Our systems are also used in electrical measurement applications, e. g. for calibrating analog input assemblies for PLC technology. For this purpose, specialized calibrators are integrated into the system; they provide traceable calibration of the relevant stimulus signals.
-
Product
USB Analyzer for USB 3.2, USB4, and Thunderbolt 3 Testing & Verification
Voyager M4x
-
The industry’s most accurate and trusted USB analyzer platform now supports USB 3.2, USB4 and Thunderbolt 3 testing and verification. The legendary Voyager family combines best-in-class probe technology with industry-leading analysis software allowing designers and validation teams to debug problems and verify interoperability for next-generation USB systems.
-
Product
PCI Resistor Card 2-Channel 1.5 Ohm To 8.19k Ohm With SPDT
50-293-124
-
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Databus-to-Network Interfaces
OBB2
-
The OBB2 is highly configurable and includes built-in standard peripherals (Ethernet, serial, and USB), along with four internal Cores that can be populated with a variety of databus protocols and discrete I/O modules. With the newest advanced set of MIL-STD-1553 and ARINC 429 modules, users can verify wave form compatibilities, test functions of bus shorts and opens, and—when combined with our CoPilot® software—perform lab, production and flight test verification and simulation right out of the box.
-
Product
PXI Programmable Resistor Card 2-Channel 2.5 Ohm to 8.19k Ohm - SPST
40-294-124
-
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PCI Programmable Resistor Card 4-Channel 2 Ohm To 127 Ohm
50-294-012
-
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Error Proofing Applications
-
ARC has assisted in Error Proofing critical processes at many companies like yours, to implement visual based process verification, data-centric process flow and, if needed, connected tooling that can be combined to improve your operation. By providing a process verification system that can be connected into your manual and automated processes, you can achieve your error proofing goals.
-
Product
Zero-footprint Timing Analysis For Critical Software
RapiTimeZero
-
*Collect timing metrics from systems that produce branch traces* Identify code to optimize for worst-case behavior*Debug rare timing events*Simplify verification through integration with your CI tool*Analyze timing behavior of libraries without source code
-
Product
PXI Programmable Resistor Card 2-Channel 3 Ohm to 131k Ohm
40-294-034
-
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Calibration Services
-
WTG's calibration package is more than just verification of performance specs. It is a complete package of services including inspection and maintenance. Our services uphold the value of the instrument and extend its lifetime.
