-
product
Test Set With Control Unit
Supreme Instrument Laboratories
Single Phase A.C. High Voltage Test set (BDV Flash Test) suitable for operation on 230 Volts, A.C. 50 Hz., designed for carrying out dielectric test on transformers, electrical switchgears, and installations. It operates on single phase A.C. and provides an output voltage zero to maximum rated voltage.
-
product
Primary Current Injection Sets
Protective devices such as relays, overload Coils, Circuit breakers and CTS etc. must be checked regularly to ensure that they are always ready to operate correctly, Routine current injection testing will quickly detect faulty or incorrectly adjusted protection circuits / devices & will be possible to prevent serious damage to the system. Primary injection kit is designed to operate on single phase 230/240 volts AC 50 HZ to develop smooth & continuous test current as for loading, calibrating, and testing of CTS, Bimetal Relays, Protection Relays etc. The test set gives high current output at low cost and with inherent safety. The primary current injection testing checks all parts of the protection system by injecting current down the cable / bus bars. The application of the primary current injection sets is to ascertain the current carrying capacity of any Conductor, insulator, connector or calibration of CTS / Bi-metallic relays etc.
-
product
Tone Test Set
240 Weathertite
The AINES Model 240 Tone Test Set is a water resistant tone generator equipped with a weathertite 2 conductor modular cord and jack. The set can be connected to the Network Interface Device (NID) with either the two individual clips or the modular cord. This allows the CPE circuit to be viewed in both directions, towards the Central Office and towards the customer premise. In the event the CPE does not have a jack, but instead has a cord, plug the cord into the Model 240s jack and transmit tone!
-
product
Bench Top Test Set
WesTest-3000/BTTS
WesTest Engineering Corporation
*PXI Based*Test Requirement Driven*Core Capability Consistency*Software Standards- ATML, IEEE
-
product
Current And Voltage Transformer Test Set
iCT1
iCT1 - CT/VT Test Set is the NEW and most advanced portable equipment capable to test current, voltage and combined transformers.With the low voltage method, known as "DC method", iCT1 is able to test Current Transformers with a very high saturation voltage, up to 30 kV, in a complete safety mode. Quick and easy to use tool, iCT1 allows to perform tests in one shot without changing the connection to the CT, thanks to the integrated 5-TAP Switchbox.
-
product
BDV Transformer Oil Test Sets
NMC''s Transformer BDV Oil Test Set is a portable unit as per relevant Indian Standard Specification IS :6792 :1992, suitable for operation on 230 / 240 Volts, A.C. 50 Hz. A three core flexible cable is connected to the unit with three pin socket to connect the mains. The H.V. Transformer is a completely dry, resin encapsulated with two H.V. terminals with mounting saddles. The center point of the transformer is earthed, so that the voltage of each terminal to earth is only half the test voltage.
-
product
Reflectance/Transmittance Test Set
RT-500
An Integrating Sphere is a hollow sphere which has its interior coated with a paint that is nearly perfectly diffuse or Lambertian and which has extremely high reflectance. Light energy introduced in an integrating sphere is reflected from the wall and distributed uniformly around the interior. A detector which is placed at a hole or 'Port' in the sphere wall sees an output which is completely independent of the angularproperties of the input light. The independence of the output of a sphere from the angular properties of the input and the uniform internal distribution of light make integrating spheres ideal for many uses.
-
product
Current Injection Sets
Built in c based Time Interval Meter measuring from1 millisec to 9999 sec. Panel with easy and clear legends to read. Continuosly variable outputs. Auto Cut-off & output isolated. Self sensing of contacts i.e. NO or NC Potential free star stop signals Available in Portable / Lab type models with metal cover
-
product
EV-DO Analysis Using NI PXI RF Test Instruments
NI-RFmx EV-DO
Highly optimized RF measurement experiencePerform physical layer analysis on EV-DO cellular signals including MODACC, ACPR, CHP, OBW, and SEMSimple access to advanced measurement parallelism
-
product
In-System Programming (ISP)
Modern assemblies today usually require on-board or in-system programming. The in-system programming (ISP) on the in-circuit test adapter represents the ideal solution for optimizing processes in ongoing electronics production.
-
product
TD Series High Voltage DC Test Set
TD2000A
TD series testing equipment is a High Voltage DC Test Set consisting of control unit and DC high current output unit. And the TD series HVDC primary injection system includes 3 types, which could output 2000Adc/4000Adc/ 8000Adc and 0.1% high accuracy, suitable to be used for different HVDC testing requirements, such as in HVDC Converting station, or railway transportation line, etc.
-
product
Kelvin Probe Set
11059A
Reduce ground-related errors and contact resistance through gold-plated flat tweezers and special gripping surfaces
-
product
PC Based High Current Test Set for Circuit Breakers and Temperature Rise Test Equipment
This equipment comprises of high current source for testing of circuit breakers with additional facility for temperature rise testing (thus incorporating testing for moulded case, vacuum & air circuit breakers as per IEC 60947-2). The system integrates a servo controlled source with closed loop current feedback to maintain the current constant. It has the necessary instrumentation for maintaining current at full load & other conditions arising in testing at high current. The bench has a PC based control system with temperature data logger (24 channel with ch-ch isolation amplifiers). The data logger displays as well as stores a set of temperature values with time.
-
product
Burden Set – Current
BSC-102
The industry has recognized the actual load (burden) on CTs is lower than the standard ANSI burdens allow. So a new IEEE Specification (IEEE C57.13.6) accommodates that fact by introducing two new burdens and two new accuracy classes. This new specification address “High Accuracy”CTs.
-
product
Modbus Diagnostic Program
Modsak
Modsak is a versatile Modbus diagnostic program. It will be of interest to device manufacturers, software developers, system integrators and field service engineers. Modsak can be used to test or simulate almost any device or system that uses the Modbus protocol: slave devices, PLC's, HMI's, MMI's, DCS's, RTU's, SCADA systems, bridges, gateways, device servers, etc.
-
product
Integration of Flash / Controller Programming
Flash or microcontroller programming can be integrated in a wide variety of ways, depending on the type and scope of the application.
-
product
Utility Card: Flash Programming Applications
This new feature enables the Keysight Medalist i3070 ICT to perform higher speed flash programming at the ICT station in the printed circuit board assembly manufacturing line. You can combine programming and testing into a single phase, to save time and money. This in-system programming (ISP) flash solution is tester-based and does not rely on fixtures, thus enabling greater flexibility and ease of debugging.
-
product
Uniload Voltage Transformer Test Set
2J6
The Type 2J6 Knopp Uniload Voltage Transformer Test Set consists of three major parts: When the Knopp Precision Transformer in the 2J6 set is compensated for, and used with, a secondary burden of 15 volt-amperes, for example, the ratio of this precision transformer is well within 0.02% and the phase angle is well within 2 minutes. The transformer, in common with other Knopp Precision Multirange Transformers, is wound so that it has practically the same ratio and phase angle accuracy on all ranges.
-
product
NI Real-Time Test Cell Reference System
778820-35
DIAdem Advanced with DAC Bundle, Perpetual License, Include 1 Year SSP
-
product
The Imperas Instruction Set Simulator
ISS
The Imperas ISS is often the first simulation product used in an embedded software development project. The Imperas ISS allows the development and debug of code for the target architecture on an x86 host PC with the minimum of setup and effort. It simply requires the cross compilation of your application and running the ISS with an argument to specify the name of the application object.
-
product
Rugged Field Test Set
MTS-207
The MTS-207 is a state-of-the-art portable PXI platform for field testing and data acquisition systems. Its proven architecture has been deployed worldwide on multiple programs including the MTS-206 Maverick Missile system flight line tester, the MTS-209 Common Armament Test Set, the AN/TSM-205B Hellfire System test Set, and many more. It combines the capabilities of the versatile and powerful PXI architecture in a compact, ultra-rugged, flightline qualified enclosure. The MTS-207 is ideal for test and data acquisition applications requiring operation under harsh environmental conditions including flightline, back-shop, or airborne applications.
-
product
SAS Protocol Test System
M124A
The SAS Sierra M124A Protocol Test System is Teledyne LeCroy's 7th generation protocol analyzer system that provides 100% accurate protocol capture of both SAS (SAS 3.0) and SATA (SATA 3.0). The industry's most widely used test platform for SAS and SATA features unmatched analysis and debug capabilities to help pinpoint problems at every layer of the protocol.
-
product
Tone Amplifier And Tone Generator Set
AM5/TG5xs
The New Tone & Amp Set are state of the Art Testers offering touch button technology, visual qTrace (quick trace) as well as audio tracer tone technology providing accurate wire location, high output volume and sensitivity, tone tracker functionality, Visual/Audible indication of Digital Traffic, filtered amplification with multiple volume levels and two normal tones and four tonetracker tones with constant and variable interrupt rates, short detection and indication, capacitive output connection, Quick change battery and low battery indication in New custom designed High impact resistance enclosures, fully sealed to IP67.
-
product
Insulating Transformer Oil Test Set
NMC make Insulating BDV Oil Test Set are used to check the di-electric strength of the transformer oil.
-
product
Software Program
Process Engineer 4.0
To benefit from the full potential of industry 4.0, process and asset experts must be empowered with analytics to answer their own day-to-day questions. With use of our self-service advanced analytics solution, process engineers will move from analytics aware to analytics enabled up to analytics expert. The new Process Analytics Engineer will be better equipped to improve overall equipment effectiveness, improve product quality and reduce costs.
-
product
DC Hipot Test Set
KVZG
KV Hipot Power Test Equipment Co.,Ltd
DC Hipot Tester is applied to measure output voltage and leakage current for zinc oxide arresters, magnetic blowing arresters, power cables, generators, transformers, circuit breakers and other equipment.
-
product
Relay Test Set Type SP-I
Supreme Instrument Laboratories
Supreme make relay testing set is designed for site testing of protective relays which simulate in common fault conditions under which a protective relay will be called into positive function. Periodic field testing is the best way of ensuring the integrity of the protective relays. We offer our relay testing set with specific testing capacity to suit different group of protective relays. The testing set operates on single phase 230 V, A.C. 50Hz. Supply.
-
product
Wide Jaw Kelvin Lead Set
6730
Wide Jaw Kelvin Lead Set. True wire four wire lead set with gold plated alligator clips that open to a wide .800? (20.3mm).
-
-
product
20kV 4 Collector Test Set
Polarity designs and manufactures the most reliable Microwave Tube Test Sets in the industry. Polarity understands the delicate structure of microwave tube devices and has built an extensive product line supporting the manufacturing process.
