Chip
Passive or active components test and their interconnected circuitry in silicon or germanium.
See Also: Integrated Circuit, IC
-
product
Automatic Programmers
SuperBOT is an automatic IC programmer with high performance and reasonable price for large-scale electronic product manufacturing. This programmer can automatically pick up, place, program, take out and pack up chips. SuperBOT 3 is capable of supporting most MCU, CPLD, serial and parallel NOR/NAND FLASH.
-
product
Time to Digital Converter-1ns 5ch
FMC TDC
Sundance Multiprocessor Technology Ltd.
An FPGA Mezzanine Card (FMC) with a Time to Digital Converter chip to perform one-shot sub-nanosecond time interval measurements.
-
product
Read-Write Analyzers
Guzik Read/Write Analyzers (RWA) work in conjunction with Spinstands to write data to the disk media and read back the signal for detailed analysis. We have two RWA-4000 series available for For Two Dimensional Magnetic Recording (TDMR) and non-TDMR technologies. The RWA 4000 series offer upto 8Gbit/sec maximum write data rate and 3.5 GHz analog bandwidth for all parametric measurements. Each RWA features a pattern generator with 1psec resolution of bit pre-compensation and supports PRML chip integration. Servo writing and processing is provided for Guzik Spinstand models. Select the pre-amplifier (UP14) as well as a variety of enhancements including programmable filters and PRML chip adapters.
-
product
SMT Rework Station
RW1210
Safely and precisely rework SMD, BGA, or LED chips. This all-in-one solution covers rework needs for even the most complex, densely populated PCBAs. Yet it is easy to use, enabling technicians to quickly master delicate alignment, placement, and heating controls.
-
product
32+2 Channel 12bit 5 GS/s Switched Capacitor Digitizer
V1742
12 bit @ 5 GS/s, 1-unit wide 6U VME64 module, Switched Capacitor technology based on the DRS4 chip (designed at Paul Scherrer Institute) 1024 capacitor cells per channel (acquisition window of ~ 200 ns @ 5 GS/s)
-
product
SparkFun FM Tuner Basic Breakout
Si4703
This breakout for the Silicon Laboratories Si4703 FM tuner chip is a little more stripped down than our FM Tuner Evaluation Board. If your project already has an amp and just needs a full-featured FM tuner, this is the board for you. Beyond being a simple FM radio, the Si4703 is also capable of detecting and processing both Radio Data Service (RDS) and Radio Broadcast Data Service (RBDS) information. The Si4703 even does a very good job of filtering and carrier detection. It also enables data such as the station ID and song name to be displayed to the user.
-
product
Varactor Tuning Diodes
Macom Technology Solutions Holdings Inc.
MACOM’s GaAs and Silicon varactor tuning diodes provide broadband performance ranging from 10 MHz to 70 GHz. They are ideal for high Q filter and VCO electronic tuning circuits and are available in die form, flip chip, plastic and ceramic packaging. These GaAs diodes boast a constant gamma series for higher frequency and high Q applications and silicon abrupt and hyper abrupt series in plastic packaging are suitable for high volume surface mount applications.
-
product
Dry Systems
Chips are made up of many layers stacked on top of one another, and it’s not necessarily the latest and greatest immersion lithography machines that are used to produce these layers. In a given chip, there may be one or two more complicated layers that are made using an EUV lithography machine, but the rest can often be printed using ‘older’ technology such as dry lithography systems. This is certainly more cost-effective for customers, since these older machines are less expensive to purchase and maintain. Read about how dry lithography systems are enabling progress.
-
product
5MP MIPI Camera Module
E-CAM55_CUMI0521_MOD
e-CAM55_CUMI0521_MOD is a small form factor, 5 MP fixed focus camera module based on AR0521 CMOS image sensor from ON Semiconductor® has a dedicated, high-performance Image Signal Processor chip (ISP) on-board that performs all the Auto functions (Auto White Balance, Auto Exposure control) in addition to complete image signal processing pipeline that provides best-in-class images and video. This low light camera module can stream uncompressed VGA (640 x 480) at 75 fps, HD (1280 x 720) at 100 fps, 1280 x 960 at 75 fps, FHD (1920 x 1080) at 65 fps, 2560 x 1440 at 38fps, 2592 x 1944 at 28 fps.
-
product
Material Identification Spectroscopy
ChipCHECK
Gastops specializes in advanced fluid sensing and analysis systems specifically designed and developed for critical equipment condition monitoring applications. ChipCHECK offers the fastest way of making on-site equipment maintenance decisions. It is a field deployable analyzer designed for rapid on-site identification of equipment lube oil. This automated maintenance decision-support tool employs innovative laser spectroscopic technology, which enables on-site analysis of microscopic chip debris. ChipCHECK provides the maintainers with quick, reliable, and conclusive information, including the total number of particles, and the size, shape, and specific alloy classification for each individual particle on the sample.
-
product
RTOS
LynxOS
The embedded market is exploding with the dawn of the “Internet of Things”. The basic idea being that almost everything will ultimately be connected to the internet and these embedded devices are becoming more complex. This means they need to run more full functioned operating systems, with connectivity and popular human interfaces, require more processing power, including multi-core chips, and are likely to be exposed to the same types of cyber attacks that we are facing in our corporate and personal computers.Lynx Software Technologies addresses these needs with our high performance LynxOS operating systems and tools based on open standards. Our new powerful RTOS security features allow embedded developers to design their systems to be more secure before they are connected to the internet.
-
product
PCI Express
PCIe
PCI Express (PCIe) has become the leading interconnect technology to succeed the Peripheral Connect Interface (PCI) architecture. The PCI Express(PCIe) architecture retains the PCI usage model and software interfaces for investment protection and smooth development migration. The technology is aimed at multiple market segments in the computing and communication industries, and supports chip-to-chip, board-to-board and adapter solutions. PCI Express 5.0 currently runs at 16GT/s or 32Gbps per lane in each direction, providing a total bandwidth of 128GBps in a 16-lane configuration which is the largest size in use.
-
product
Big Easy Driver
The Big Easy Driver, designed by Brian Schmalz, is a stepper motor driver board for bi-polar stepper motors up to a max 2A/phase. It is based on the Allegro A4988 stepper driver chip. It's the next version of the popular Easy Driver board.
-
product
8 Channel Sample & Hold and Signal Conditioning Board for Group3
All channels provide for voltage division ahead of transient suppression before going into the S&H ICs. Channels that are sampled and held use a common sample and hold pulse that samples while high and holds while low. Jumpers on each S&H chip allow buffering of analog signals where sample and holds are not required. An advantage to the buffers is that it provides a high input impedance for high impedance voltage dividers.
-
product
Computer-On-Module
CM12001
LinkedHope Intelligent Technologies Co.,Ltd.
CM12001 integrates the complete functionality of vertex86DX,offering a CPU, system BIOS, 16bit DRAM up to 512MB, keyboard controller, real-time clock, and IDE compatible onboard Flash hard disk up to 16GB. The solution includes a highly integrated embedded CPU chip made by DMP. It has x86 Compatible Processor Core.This module is designed for embedded applications. The pin out of its’ Dimm-pc bus connector corresponds in large part to the pin out of a standard ISA bus. It offers peripheral functions such as USB, PS2, LPT, COM interface...
-
product
N2 O2 Analyzer
GNL-IN881 Series
Shanghai ChangAi Electronic Science & Technology Co.,Ltd
GNL-IN881 series analyzer is the online intelligent measurement instrument, which adopting advanced ion current oxygen sensor with single chip technology. N2%=100%-O2%.It has been widely used in the fields of nitrogen separation from air, fertilizer, petrochemicals and biological fermentation. - See more at: http://en.ci-ele.com/8aedb8bf-ef48-4f8c-127a-797c939a6181/78ea4933-855f-c270-f389-d6ac3b6fe432.shtml#sthash.Dk7zX5DN.dpuf
-
product
Microelectro Mechanical Systems And MEMS Sensors
NevadaNano has spent a decade integrating multiple, complementary chemical sensors on a single silicon chip. We call it the Molecular Property Spectrometer™ (MPS™). The MPS Gas Sensor works together to measure a variety of thermodynamic and electrostatic molecular properties of sampled vapors, liquids, and particles. In less than a second, the chip creates a large, rich dataset of chemical information. Then, Custom MPS software identifies the types of molecules present in an unknown sample.
-
product
Digital Step Attenuators
Analog Devices provides a range of broadband IC digital attenuators that come in low cost, leadless surface mount packages. Our digital attenuator family offers excellent attenuation and includes off chip ac ground capacitors for near dc operation, making it ideal for an extensive number of RF and IF applications.
-
product
Module Spectrum
nRF52832 Series
Raytac nRF52832 module spectrum covers MDBT42Q, MDBT42 and MDBT42V series with both Chip Antenna and PCB Antenna option for selection.
-
product
Module Spectrum
nRF52810 Series
Nordic nRF52810 solutioin features an Arm Cortex-M4 processor with 192 KB Flash and 24 KB RAM with 32 GPIO available. Supports SPI, UART, I2C, PWM interfaces with both Chip Antenna and PCB Antenna option for selection.
-
product
Inductor Tester
An impulse can be applied to the coil of a chip power inductor to perform insulation tests (surge tests) within the windings.
-
product
MPI Sorter Series
MPI’s Sorter Series are improving production efficiency and yields for market sectors related to LED chip, package production, discrete device handling, and IC substrate manufacturing. Deploying MPI’s Pick & Place technology, the Sorter Line offers dedicated sorting and defect inspection solutions particularly suited for GaN, GaAs, Vertical LED Chip, Flip Chip, and Laser Diode applications. With a proven heritage of and market-advanced technologies, MPI offers competitive and differentiated solutions that are scalable and cost-effective.
-
product
Flexible Pick & Place Machine W/ 64-feeder Capacity
MC400
The MC400 Pick and Place machine places an enormous range of components, quickly and accurately, from 0201s through 100 x 150 mm SMDs, including BGAs, MBGAs, CSPs, µBGAs, MLFs, flip chips, odd form components and ultra-fine-pitch parts down to 15 mil. The system is easy to program and operate and comes standard with universal CAD conversion and teach-in capability.
-
product
Arduino CAN Shield
IFB-10003-AWP
CAN (Controller Area Network) communication has become ubiquitous in industry. It is used in automotive applications (part of OBD and many other datalinks), on-highway trucks (J1939), industrial machinery and instrumentation, and equipment applications (factory automation). This shield is designed to provide a CAN 2.0 front-end interface for 5V Arduino modules (Uno, Mega, etc). The module uses SPI to communicate to the Arduino, and requires an aditional chip select pin. An optional interrupt line to the MCP2515 and two LEDS are also provided. The chip select and interupt lines are selected via zero ohm resistors and have several configuration options for flexibility stacking additional shields. A set of stackable headers is included with this board, not installed. An optional on-board voltage regulator may be used to supply 7.5V to the Arduino's 'Vin' pin (which is regulated to 5V by the Arduino's on-board LDO). The CAN shield regulator supports a wide input range of 9V to 32V. This makes it possible to cleanly build a stand-alone CAN node (remote sensor) without the need for a separate Arduino power supply!
-
product
Digital Input/Output Card
IOD-144
This is a 144-bit full-size card. A Programmable Peripheral Interface chip, type 8255-5 provides three 8-bit ports (A, B, and C) for each 24-bit group. Each port can be independently programmed for either input or output. Port C can also be configured as two 4-bit ports. These cards fully implement Mode 0 of the 8255 PPI chip. (Consult the factory if you desire to operate in Mode 1.) Type LS245 bi-directional transceivers sink 24 mA (optionally 64 mA) and source 15 mA. These transceiver buffers provide hysteresis correction on inputs and added drive capability on outputs. The direction of the transceivers is set by software.
-
product
Universal Programmer Superpro 6100N
Until now,Support 401 IC manufacturer, 103004 pcs devices and keeps growing.Features:Supports 87454 types of devices from 305 IC manufacturers (by 3/15/2013) and keeps growing.Supports EPROM、Paged EPROM、Parallel and Serial EEPROM、FPGA、PROM、FLASH(NOR & NAND)、BPROM、NVRAM、SPLD、CPLD、EPLD、Firmware HUB、Microcontroller、MCU；Supports devices with Vcc as low as 1.2V. Socket Adaptors available for DIP、SDIP、PLCC、JLCC、PGA、LGA、SOIC、SOJ、SOT、QFP、TQFP、PQFP、VQFP、MQFP、LQFP、TSOP、SOP、TSOPII、PSOP、SSOP、TSSOP、SON、EBGA、FBGA、FTBGA、VFBGA、μBGA、CSP、SCSP、QFN、HVQFN etc.High programming speed.Built with 144 universal pin-drivers. Universal adaptors are available for varies packages up to 144 pins. Quick new device support. Popular NAND FLASH Platform supported including Samsung (XSR1.0/1.6), QualComm, HYNIX（HIFFS）, MTK(Solution V1.1), ICERA (v1.0/2.0), ST （7162、7141等）, AMLOGIC(IF2/0), REALTEK, PICOCHIP, DataLight ( Flash FX Pro), Marvell(310/303/920/935…), BroadCom, ZTE, Intel (CE4100)，UBI, LEADCORE(L1809OG), MSATR etc. Customer-specific NAND solution available.PC hosted mode and stand-alone dual modes. Under PC hosted mode the programmer is controlled by a PC via USB2.0 (high speed) to program a chip. Under stand-alone mode the programmer is controlled via a 6-KEY keypad and a 20 character by 4 line LCD display. A CF card is used to store the project files.User can operate multiple units to construct a concurrent multiprogramming system thank for the stand-alone mode. IC manufacturer approved programming algorithms are used for high reliability.Testing functions for logic devices.Advanced and powerful software functions.Production mode starts chip operation at the moment the chip is inserted in the socket properly.Project function simplifies processes such as device selection, file loading, device configuration setting, program option, and batch file setting into one touch step.Password can be set for project files and production volume controlBatch command combines device operations like program, verify, security into a single command at any sequence.Dynamic buffer makes it possible that each chip is programmed with different data file. Applications including serial number, MAC address etc.Log file is useful for quality tracking.Many safety mechanisms are built including self-diagnosis, wrong chip placement detection, poor-pin-contacting detection, ID checking, over-current and over-voltage protection etc.Windows XP/Vista/Win7/ Win8/Win10 compatibility.
-
product
3.4 MP Custom Lens Low Light Camera Module
e-CAM30_CUMI0330_MOD
e-CAM30_CUMI0330_MOD is a high performance, small form factor, 3.4 MP pluggable Low Light Camera Module with S-Mount lens holder. It is based on AR0330 - a 3.4MP CMOS Image sensor from ON Semiconductor®. It has a dedicated, high-performance Image Signal Processor chip (ISP) on-board that performs the entire Auto functions (Auto White Balance, Auto Exposure control) in addition to complete image signal processing pipeline that provides best-in-class images, videos and the optional MJPEG compressions.
-
product
Isolated Input Card
mPCIe-II-16
The mPCIe-II-16 consists of a type F1 PCI Express Mini Card (mPCIe) interface board that connects to a Mobile-ITX-sized, DB-37M Isolation Module via an included 9” cable. That module is designed to be easily panel-mounted in any application environment. It uses the high speed PCI Express bus to transfer digital data to and from the card. The digital I/O is compatible with 8255 PPI chips making it easy to program.
-
-
product
Low Light USB Camera With Microphone
Conversa
Conversa, camera for conversation (See3CAM_CU38), is a 3.4 MP low light USB 3.1 Gen1 camera with built-in stereo microphone providing 16bit audio @48KHz. This low-light USB camera is the next advanced version of our flagship product See3CAM_CU30, with built-in stereo microphone for crystal clear sound. It is a plug-and-play (UVC and UAC) compliant USB 3.1 Gen1 SuperSpeed camera and is also backward compatible with USB 2.0 host ports. It has S-mount (M12) lens holder which allows customers to choose and use the lens according to their requirement. It has a dedicated, high-performance Image Signal Processor chip (ISP) that performs all the Auto functions (Auto White Balance, Auto Exposure control).
