HV
electric power transmission is > 35,000 volts and for safety AC > 1000 and DC > 1,500.
See Also: High Voltage, High Voltage Switching, High Voltage Meters, High Voltage Detectors, High Voltage Programmable Power Supplies, Glove
-
Product
DC HV tester/ hipot
-
Wuhan Fanke Transformer Manufacture Co., LTD
1) DC HV tester/ hipot tester/portable-type2) Suitable for DC HV. test or leaking current test
-
Product
Low Voltage DC / Battery Powered HV Amplifiers
WMA-02 And WMA-02LF
-
The Falco Systems WMA-02 is a high voltage amplifier that runs from an 24 - 30V DC power supply and can be battery powered if required, e.g. for use in a Faraday cage. Its internal high voltage generator is inductor-free and hence does not spread magnetic interference in sensitive experimental setups. The output noise is impressively low at 4mVrms. For extremely low noise applications where bandwidth is not an issue, a dedicated WMA-02LF version is available that contains an output low pass filter capacitor which reduces the bandwidth to 50Hz, but makes the noise drop to below 0.2mVrms. This bandwidth-limited amplifier is ideal for MEMS or piezo positioning with manual voltage adjustment.
-
Product
9-Pin D-Type Male, Solder Bucket, HV
40-960-009-M-HV
D-Sub Male Connector
9-Pin Male D-Type Connector, High Voltage, Solder Bucket - With Backshell
-
Product
HV High Performance Circuit Breaker Analyzer
CBV-32
-
We conceived the CBV-32 to provide the best range of testing for electrical facilities such as circuit breakers (using gaz, oil, air, vacuum…) or synchronous condensers all the way up to 800kV and more. It combines Timing, Motion Dynamic Resistance Measurements, and Vibration, all in a single test.
-
Product
HV Switch Test Equipment
-
KV Hipot Power Test Equipment Co.,Ltd
High Voltage testing is usually performed to qualify the device to operate safely during rated electrical conditions, a way to check the effectiveness of its insulation. The objective sought during the high voltage testing will determine the type and amount of voltage applied and the acceptable current flow.
-
Product
Cable Assy 9-Pin D-Type, F/F, 2m, HV
40-970-009-2m-FFHV
Cable Assembly
A 9-Pin D-Type Cable Assemby for general use constructed from PTFE Type C insulated wire. The connector assembly can be secured to the product by screwlocks.
-
Product
HV & AC Resonant Equipment
-
Kvtester Electronics Technology Co.,Ltd
This kind of products are small in volume, light in weight, with compact structure and multiple function, general-purpose and easy to use. Applies to the test of frequency or insulating intensity under DC ,HV for all kinds of HV electric equipments, components, insulated material in electric system, industrial and mining enterprises, traffic , post and telecommunications, science institute, etc.
-
Product
Raptor HV High Voltage Tester
-
The Raptor-HV, also called the high voltage slave, is an optional product that extends the Raptor’s applications to tests that require the use of a moderately high AC voltage.
-
Product
Cable Assembly, 50-Pin D-Type, Female to Female, 1m HV
A050DF5-050DF5-HA100
Cable Assembly
50-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24 AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assemblies can be secured to the mating part by a screwlock. The 50-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
Product
Cable Assy 9-Pin D-Type, M/M, 1m, HV
40-970-009-1m-MM-HV
Cable Assembly
9-Pin D-Type Male to Male Cable Assy, High Voltage, 1m Long
-
Product
Cable Assembly, 37-Pin D-Type, Male to Unterminated With Tinned Ends, 2m, HV
A037DM5-T-HA200
Cable Assembly
The 37-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 37-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
Product
Cable Assembly, 50-Pin D-Type, Female To Female, 2m HV, Exit Away From Pin 1
40-970-050-2m-FF-HV
Cable Assembly
50-Pin Female to Female D-Type Cable Assembly, High Voltage, 2m Long, 45º Cable Exit Away From Pin 1.
-
Product
Cable Assembly, 9-Pin D-Type Female To Unterminated With Ferrules, 0.5m, HV
40-972-009-0.5m-FU-HV
Cable Assembly
A range of 9-Pin D-Type High Voltage cable assemblies with unterminated connections on one end, constructed from PTFE Type C insulated wire. The unterminated connections are coded to match the connector pin designation and include crimped on ferrules to ensure the wire strands cannot break when they are terminated.
-
Product
Cable Assembly, 37-Pin D-Type, Female to Unterminated With Cut Ends, 0.5m, HV
A037DF4-C-HA050
Cable Assembly
The 37-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 37-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
Product
Cable Assembly, 50-Pin D-Type, Male to Female, 1m HV, Exit Away From Pin 1
40-970-050-1m-MF-HV
Cable Assembly
50-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24 AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assemblies can be secured to the mating part by a screwlock. The 50-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
Product
Cable Assembly, 50-Pin D-Type, Female To Unterminated With Ferrules, 1m HV, Exit Away From Pin 1
40-972-050-1m-FU-HV
Cable Assembly
50-Pin Female to Unterminated D-Type Cable Assembly, High Voltage, With Ferrules, 1m Long, 45º Cable Exit Away From Pin 1.
-
Product
MPOD HV Module
-
WIENER presents with Mpod a new, universal multi-channel low voltage (LV) and high voltage (HV) computer controlled power supply system. Offering highest channel density the MPOD mainframe can house up to 10 plug-in modules which can be mixed in type and parameters. Up to 480 individually controlled high voltage channels are available in one mainframe
-
Product
Cable Assembly, 37-Pin D-Type, Male to Unterminated With Ferrules, 0.5m, HV
40-972-037-0.5m-FU-HV
Cable Assembly
The 37-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 37-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
Product
Dual Channel HV Amplifier with Phase Inverter
A400DI
-
This unit contains two independent A400 amplifiers that share common ground reference and power supply. Please see A400 page for technical details.It features also a low voltage phase inverter that inverts the signal applied to the input of channel 1. The resulting signal can then be connected to the input of channel 2 by means of a short BNC cable (supplied). As a result the two outputs operate in counter-phase. Connecting a load between the outputs effectively doubles the amplitude range. Please note that the load cannot have any connection to ground.
-
Product
9-Pin D-Type, Right Angled PCB, Female, HV
40-963-009-RF-HV
D-Sub PCB-Mount Connector
9-Pin Female Right Angled D-Type Connector, High Voltage - PCB Mount
-
Product
Cable Assembly, 50-Pin D-Type, Female to Female, 1m HV, Exit Away From Pin 1
40-970-050-1m-FF-HV
Cable Assembly
50-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24 AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assemblies can be secured to the mating part by a screwlock. The 50-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
Product
50-Pin D-Type Male with Backshell, HV
40-960-050-M-HV
D-Sub Male Connector
This connector is designed to allow users to directly terminate cables with soldered connections.
-
Product
CableEye® HV-Rated QuickMount™ Housing for CAMI Connector Boards
CBH2
-
CAMI Research Inc. (Acton, MA) has released a High-Voltage (HV)-rated QuickMount housing (CBH2) for its CableEye® automation-ready, cable and wire harness testing systems. As a free-standing, quick-release board fixture, it allows users to connect CAMI’s test interface boards to the 64-pin headers of any expansion module - even at some distance. The housing may be used with any CableEye model and is rated to 2100 Vdc / 1500 Vac.
-
Product
Cable Assembly, 50-Pin D-Type, Female to Unterminated With Tinned Ends, 0.5m HV, Exit Away From Pin 1
A050DF4-T-HA050
Cable Assembly
50-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24 AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 50-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
Product
Cable Assembly, 37-Pin D-Type, Male to Unterminated With Tinned Ends, 0.5m, HV
A037DM5-T-HA050
Cable Assembly
The 37-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 37-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
Product
Cable Assembly, 50-Pin D-Type, Male to Male, 2m HV, Exit Towards Pin 1
A050DM5-050DM5-HA200
Cable Assembly
50-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24 AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assemblies can be secured to the mating part by a screwlock. The 50-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
Product
Cable Assembly, 50-Pin D-Type, Male to Female, 0.5m HV
A050DM5-050DF5-HA050
Cable Assembly
50-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24 AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assemblies can be secured to the mating part by a screwlock. The 50-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
Product
Cable Assembly, 37-Pin D-Type, Male to Unterminated With Ferrules, 0.5m, HV
40-972-037-0.5m-MU-HV
Cable Assembly
The 37-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 37-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
Product
Cable Assembly, 50-Pin D-Type, Male To Unterminated With Ferrules, 2m HV, 45º Exit Away From Pin 1
40-972-050-2m-MUHV
Cable Assembly
50-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24 AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 50-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
Product
Low Voltage DC / Battery Powered HV Amplifiers
WMA-01 And WMA-01LF
-
The Falco Systems WMA-01 is a high voltage amplifier that runs from an 24 - 30V DC power supply and can be battery powered if required, e.g. for use in a Faraday cage. Its internal high voltage generator is inductor-free and hence does not spread magnetic interference in sensitive experimental setups. The output noise is impressively low at 3mVrms. For extremely low noise applications where bandwidth is not an issue, a dedicated WMA-01LF version is available that contains an output low pass filter capacitor which reduces the bandwidth to 50Hz, but makes the noise drop to below 0.1mVrms. This bandwidth-limited amplifier is ideal for MEMS or piezo positioning with manual voltage adjustment.
