-
Product
Test Sockets & Interposers
Silmat
-
Innovative technology platforms and multiple product families for BGA, LGA, QFN and CSP packages down to 0.3mm pitch. High frequency bandwidth > 40 GHz..
-
Product
Battery Test Systems
-
Was designed to meet the specific demands of our loyal customers. This system is used to test both single cell batteries as well as super-capacitors.
-
Product
Pil Dielectric Test Sets
DTS Series
-
The DTS Series provides repeatable and accurate measurements of the breakdown voltage of insulating oils used in electrical equipment. The DTS-60D & DTS-100D offer 60 kV AC and 100 kV AC output respectively. They include three user-selectable, automatic voltage rates-of-rise, and automatic voltage shutdown with the meter indicating the flashover voltage. Various test cells are available.
-
Product
Pressure Test & Calibration Pumps
-
Pressure Test Pump is a hand operated pressure pump designed to generate pressure from 95% vacuum to 1,500psi (100bar). A high-quality screw press is designed for fine pressure adjustment, with an adjustment resolution up to 10 Pa (0.1 mbar). A specially designed shut-off valve makes the pressure as stable as possible during calibration. A built-in gas-liquid isolator protects the pump from moisture and dirt to reduce the need for maintenance. Two hand-tight quick connectors installed on the pump allow easy connecting and disconnecting to the test pump without the need for PTFE tape or wrenches. The 918 is an ideal comparison test pump for pressure instruments calibration.
-
Product
V2X Test Tools
-
Validate and verify your V2X application with our Mx-Drive Mobility Simulator. Use the Mx-DSRC Compliance tester for USDOT certification.
-
Product
Sensors And MEMS Test
-
Easy docking and undocking of the MEMS modules to the standard test handler whether Gravity, Pick and Place or Test in StripTest in the complete tri-temp range for ambient, hot and cold (automotive certified)Easily convertible to other packagesDownscaled stand-alone engineering set-up availableGlobal support by experienced Cohu Field Service and Applications staff
-
Product
Primary Test Equipment
LET-400-RDC
-
The LET-400-RDC is designed to perform most of the primary tests that are necessary in substations commissioning. It allows to perform with sufficient power, all the primary current injections to test the proper function and wiring of all the elements that compose the protection and measuring section in a substation.
-
Product
Cable Test Box
-
Cables are a critical part of any sensor measurement system and damaged cables cause frequent delays during test setup. PCB has developed a relatively simple device to test cables on a channel by channel basis for BNC, 10-32, and 5-44 coaxial connectors. Simply connect both ends of the cable and faults will be indicated for shield failure, conductor failure, or short circuit shield to conductor. Power is provided by a single, replaceable 9 volt battery.
-
Product
VLSI Test System
3380P
Test System
The 3380D/3380P/3380 test system have 4 wires HD VI source and any-pins-to-any-site high parallel test (multi-sites test) functions (512 I/O pins to test 512 ICs in parallel) that can meet the upcoming higher IC testing demands.
-
Product
Axle Damping Test Bench
C_MSD C 13.0 W220 | VP 215050
-
Maschinenbau Haldenwang GmbH & Co. KG.
The axle damping test bench C_MSD is characterised by a fast and precise mechanical testing of the axle damping. Through the frequency-controlled plate activation via electric motors, the maximum vibration amplitude is calculated and then the axle damping is evaluated according to the Lehr damping principle. The fully automatic test sequence, including the calculation of axle and vehicle weight, saves time and allows a reliable assessment of the axle damping.
-
Product
EMC Test Equipment
TDEMI G series
-
TDEMI stands for a novel generation of EMI measurement systems providing real-time analysis and enabling the user to perform high-quality emission measurements in a fractional amount of time compared to conventional EMI receiver technology. Ultra-fast Analog-to-Digital Conversion as well as real-time signal processing allows to emulate the behavior of instruments like oscilloscopes, receivers and spectrum analyzers. Due to the TDEMI's powerful signal processing hardware platform, corresponding to a computation power of approx. 80 conventional. PCs, such measurements are extremely fast in comparison to state of the art solutions.
-
-
Product
Built-In Relay Self-Test Diagnostic Test Tool
BIRST
-
Verification and diagnosis of complex switching operation in a test system has always been an issue. BIRST (Built-In-Relay-Self-Test) diagnostic test tool provides a quick and simple way of finding relay failures available on some of our LXI and PXI switch matrices.
-
Product
MECHANICAL TEST FIXTURE KITS
TX-MT-SERIES
-
Test-X MT Series mechanical kits are an affordable solution to printed circuit board testing. With multiple configurations and available options, this product is sure to meet your testing needs. The MT Series features a hinged 3/8" FR4 probe plate, tooling holes for accurate drilling, and side handles for easy transportation.
-
Product
High Temperature Test Clip
-
- High temperature HT Parrot Test Clips PCS-HT , can be efficiently used at high temperature up to 160° Celsius. Plastic body is HT poly-amide.- High temperature HT Parrot Test Clips PCS-HT , can be used in ovens being connected with the silicone cables.
-
Product
ARINC-708 Module
M4K708
Test Module
The M4K708 module is an ARINC-708 / 453 2-channel test and simulation module for the Weather Radar Display Databus. The M4K708 supports two ARINC-708 / 453 channels, each selectable as transmit or receive.
-
Product
Emulation & Test Interface
-
Solder down modules to suit any package type provides a cost effective solution for replacement test heads, male or female. The mating top modules can incorporate either a ZIF or standard IC socket and the addition of optional test pins if required from RS Components.
-
Product
Modular Test Platform
MPA®Multi-Protocol Analyzer
-
The MPA® Multi-Protocol Analyzer is an advanced packet optical transport traffic generation and analysis platform specifically designed for the demands of R&D, SVT, and manufacturing testing environments. The MPA provides simultaneous independent multi-port testing from 1G to 400G for Ethernet/IP, OTN & SDH/SONET and Fibre Channel.
-
Product
Board Test
-
The Horizontal/Vertical Signal Integrity Manual Work Station allows for multiple size circuit board configurations.
-
Product
Non-Destructive Test Resonant Inspection Station
RAM-TEST-FIXTURE
-
The NDT Test Station, Model RAM-TEST-FIXTURE Resonant Inspection System is an ideal choice for testing when repeatable manual inspections are required. The innovative Test Station allows precise control of part positioning with an adjustable table ranging up to 6.25 inches (158.75 mm) in height.
-
Product
Motor Test for Stepping Motors
-
*Stable measurement: Since it uses Prony braking, this model provides stable measurement unaffected by moments of inertia and no coupling loss. In addition, the resulting measurements allow data correlation via the traditional double-balance method.*Precision measurement method: This model’s judgment of synchronization loss achieves high stability using algorithms developed by Sugawara Laboratories. Measurement mode can be chosen based on step angle. For pull-in torque, startup can be measured consistently from the holding state. Allows measurement at 1-Hz resolution.*Broad measurement range: This model offers a range of seven available measurement heads, from 0.5 N to 50 N, allowing use for high-precision measurements. Through selection and use of pulleys, this model can also be used to measure small motors of 0.5 mN·m or less or 500 mN·m motors. Pulley diameters and other settings are easily configured using a personal computer running Windows®. Note: Any of the seven available heads may be attached to a single measurement component.*High-visibility measurement data: Motor characteristics are easily ascertained on automatically plotted performance graphs. Measurement data can be overlaid up to four times. In addition, the cursor can be used to read accurate values from measurement points. Hard copies of data displayed on-screen can be printed from a personal computer.*Can be controlled using standard personal computers: Allows control of measurement operations and display and storage of data from a standard personal computer running Windows®. Data is stored in CSV-format files for compatibility with other software applications.
-
Product
Test Stand Engineering
-
m+p international has the expertise, experience and all resources necessary to design and construct custom-made vibration and functional test stands for various industries. You determine the range of services, the time frame and the budget.
-
Product
Test Kit
Metriso B530
-
Wolfgang Warmbier GmbH & Co. KG
Test voltage / Test current: 1 mA < I < 1,3 mAHigh ohmic range: DC 10 volts,100 volts and 500 voltsTest range:low ohmic range: 1 to 10 kOhmhigh ohmic range: 1 kOhm to 199 GOhmOperation: Battery operatedProbes:2x Model 870 (weight: 2,27 kg / ø 63,5 mm) with conductive rubber (grey) and extension,1x hand-held probe Model 45
-
Product
Waterproof Test Chamber
JL-XC
-
JL-XC series waterproof test chamber is mainly used for small electronic and electrical products. Such as lamps, electrical cabinets, electrical components and so one. The products are tested for physical and other related properties under simulated climatic conditions. After the test, it is judged whether the performance of the product meets the requirements by verification, so as to be used in the design, improvement, verification and factory inspection of the product. Comply with IEC60529:2001 《Degrees of protection provided by enclosures (IP Code)》, GB4208-2008 《Shell Protection Grade (IP Code)》 14.2.8 Terms and GB7000.1 《Lamps Part 1: General Requirements and Tests》 9.2.9 Terms.
-
Product
CT/VT Test System
-
Fully pre-wired comprehensive turn test system. *Suitable for CTs up to 6000A & VTs up to 132kV. * Precision to (0.005 class) internal multi-ratio standard CT. * Internal 4KA current source. * State-of-the-art Instrument Transformer Test Set AITTS-98 with computer & printer interfaces. * Electronic potential divider facilitates testing any VT ratio upto 132kV. * Current & potential burdens.
-
-
Product
Fiber Optic Network Test
-
Test and characterize fiber optic cables, assemblies and network with unmatched speed, precision and spatial resolution. Luna’s OBR reflectometers can analyze loss with a spatial resolution and sensitivity unmatched in the industry.
-
Product
Test Voltage Indicators
PRV240FS
-
Verify your test tool works without unnecessary exposure to shock and arc flash. Make the process easy by using the PRV240FS Proving unit. Verifying that your T6 electrical tester is working properly reduces the need for personal protective equipment (PPE) when a known voltage source is not available for verification before tests are performed.
-
Product
Eclipse Test Development Environment
-
The Eclipse Test Development Environment automatically creates tests that are used to bring up new products in the lab. Failures can be quickly debugged using software tools such as the Eclipse Timing Diagram Analyzer and the Schematic Logic Probe.
-
Product
Cogging Test System
CTS
-
Magtrol’s Cogging Test System is a stand-alone test system designed to control and measure Detent Torque, Cogging Torque and Friction Torque. The test System includes a precision geared motor, a TS Series Torque Sensor integrating a 5 000 pulses encoder. CTS 100 to CTS 102 have a built-in security clutches to avoid system overload by mishandling when not in use. The geared motor drives the MUT (Motor Under Test) at a low speed from 1 to 10 rpm (respectively 8 rpm for CTS 103 and CTS 104), while acquiring its cogging torque related to angle position.
