Wire Locators
detect an induced or directly transmitted signal through a cable to trace its location.
-
product
Fault Locator
WEEZAP
WEEZAP is an LV vacuum circuit breaker combined with advanced measurement and protection capability.
-
product
Drawing Die And Wire Measurement
DGMS – Die Geometry Measuring System
Optik Elektronik Gerätetechnik GmbH
Measuring system for diameter, roundness, reduction angle and bearing length of wire drawing dies.
-
product
Bulk Wire and Cable
Teledyne Marine Cable Solutions
With 50 years of dedicated experience in providing cable and interconnect solutions, Teledyne Cable Solutions meets challenges for application-specific, multi-core cables for harsh environments and complex ruggedized cable assemblies and harnesses.
-
product
Tool, Crimp, QuadraPaddle And TriPaddle, Receiver And ITA, Locator Required
910101103
Tool, Crimp, QuadraPaddle and TriPaddle, Receiver and ITA, Locator Required
-
product
Wired Adapter for PXI, for National Instruments PXI-4110
510109469
Wired adapter or pull-thru from a 64 position TriPaddle receiver module to one 6 position Mini-Combicon plug and one 2 position Mini-Combicon plug.
-
product
High Altitude Wiring Clamp
Weshine Electric Manufacturing Co., Ltd
1. The operation is simple, through pushing and pulling the special operation lever can realize the clamp mouth free opening and closing, complete the wiring work.2. Connection clamp between the upper and lower jaws of the use of the principle of moving pulley to save the effort, the use of smaller tension can be obtained larger clamping force.3. There is a steel needle inside the clamp mouth to ensure good contact between the clamp mouth and wiring position
-
product
Visual Fault Locators
MVFL Series
Shanghai Tarluz Telecom Tech Co., LTD
MVFL series Visual Fault Locators is meet the Class IIIA product, which is the easiest way to identify fibers from end to end and locate polished connector endfaces. Its red laser shines through most yellow-jacketed fibers to help you pinpoint breaks, bends, faulty connectors, splices and other causes of signal loss. The 1mW output power enable the MVFL has a reach of up to 5 km. MVFL seires VFL locates faults visually by creating a bright red glow at the exact location of the fault on single mode (SM) or multimode (MM) fibers. Due to its small size, lightweight and simple but proven design, the MVFL can accompany you anywhere In your pocket or belt pouch in harsh environment
-
product
Metal Cover Locator
CS880
The CS880 Metal Cover Locator is a metal detector that will locate lost or hidden metal objects. It is most commonly used for locating manhole covers through tarmac and grass.
-
product
12-600V AC Adjustable Non-Contact Wire Tracer
5220
Peaceful Thriving Enterprise Co Ltd
This non-contact voltage tester, can be used to test the presence of AC voltage from 12V~600V, no need of metallic conduction, easy to read by visual and audio indication. Locates breaks along live, insulated wires and power cords. Adjustable sensitivity allows tracing of wires behind walls, around switches or receptacle.
-
product
Wire Harness/Automotive Probes
As a market leader, Feinmetall offers the largest product portfolio of application-specific contact probes and accessories for test module construction and wire harness testing. With innovative and economical solutions, we meet customer requirements and set trends in wire harness and automotive testing technology.
-
product
Ground Fault Locator
K-800
Kongter Test & Measurement Co., Limited
Kongter’s K-800 Ground Fault Locator is the new model which is developed to fast detect, trace and pinpoint virtual ground faults in LIVE DC systems where electrical cables have breakage with current lost to ground.
-
product
Visual Fault Locator
TM191
TM191 series visual fault locator is used for the measurement in single mode or multi-mode fibers. It features a rugged design, a universal connectorand an accurate measurement
-
product
Tool, Insertion, QuadraPaddle, ITA, Wire Wrap Contact
910113106
Tool, Insertion, QuadraPaddle, ITA, Wire Wrap Contact - this tool is used for insertion of QuadraPaddle ITA Wire Wrap Contacts (P/N 610138122).
-
product
Cable Fault Locators
Every day, GAOTek cable fault locators are used by electricians and technicians to find faults and breaks in underground electrical and communications cables.
-
product
Fault Finder for Electrical Wiring Open / Short Circuit
FF310
42 V Ready: for use in the new generation of vehicles with mixed or single 42 Volt systems. Operates on DC voltages from 6 to 42 volts. Internally protected against power surges and overloads. 8" flexible probe allows reaching wires in congested places. Transmitter and Receiver LEDs show open or short circuit conditions.
-
product
Bench-Top Wire Crimp Pull-Force Tester
PT-1500
PT-1500 Bench-Top Wire Crimp Pull-Force Tester, Manual Lever-operated for 5.84mm 8-30 AWG
-
product
Cable Fault Locator
TX2001
Lowest Cost Full Specification Professional Graphical TDR Rugged Palm Top Design 350g (12oz) 5 Measurement Ranges up to 3000m (10,000ft) 50, 75 & 100 ohm Selectable Impedance Built in Tone Generator for Pair Tracing & Identification Suitable for testing all Communications Cables Water & Dust Proof to IP54 Complete with tool-belt holster & test leads
-
product
ITA, I2 Micro ICon, Wired, QuadraPaddle, 36", Flying Leads
410130409
ITA, i2 Micro iCon, Wired, QuadraPaddle, 36", Flying Leads This i2 Micro iCon comes wired with a flying leads cable assembly containing 168 QuadraPaddle patchcords with 24 AWG PVC.
-
product
Thumpers and Cable Fault Location
Cable testing can be broken down to different steps of the process, starting with a time domain reflectometer test to look for an incident signal on the line or, in some high resistance situations, VLF testing. These tests will identify a fault, allowing you to move on to pre-locating it. In some low resistance faults this will occur alongside the identification via the TDR.
-
product
Receiver, G18, 18 Module For Discrete Wiring
310120101
The lightweight and rugged 18 module Receiver provides a solution that will accommodate larger ATE chassis’ (PXI, VXI, SCXI). It allows immense versatility by affording space for up to an 18 slot PXI chassis.
-
product
Wire Piercing Clips
619
This new clip makes wire piercing much easier. Just slide the wire into the cradle and screw the pin down into the wire. This method is clean and leaves minimal wire damage. If you have to proceed to pierce the wire, do it the right way with 619.
-
product
Trailer Wiring Buddy 7 Pin Flat
222
*Each signal from vehicle emits a unique tone *Electric brake control signal illuminates red LED *Loud beep can be heard over shop noise *Time Saver! Just apply brakes, right/left turn signals, running lights, engage reverse & 12 Volt Charging voltage *Greatly reduces time spent verifying vehicle trailer wiring *Very simple & easy to use - saves time!
-
product
Power Cable Fault Locators
We're professional power cable fault locator manufacturers and producers in China, supplying the best customized service. Feel free to buy high quality power cable fault locator from our factory. All our portable products used in utility locations are with CE certification.
-
product
Wire Abrasion Tester
SG-D03DG
This machine is mainly based on UL1581 / UL83 standard abrasion test wire and cable testing requirements .
-
product
Travelling Wave Fault Location Test Kit
PH Series
PH series travelling waveform fault locating relay/equipment test set is a new device to meet the needs of testing and verification for travelling wave fault location equipment and protection relay with TWFL function.
-
product
Hazardous Location Transmitter
X80 Series
The ECD Hazardous Location Transmitters – Model X80 Series provides the same capabilities and general feature set as the general purpose T80 Universal Transmitter. Various configurations are available as single or dual channel for the continuous measurement of pH, ORP, pION, Dissolved Oxygen, Turbidity, Conductivity or Resistivity. The Model X80 transmitter digitally communicates with any ECD Model S88 and/or S80 Intelligent Sensor, automatically configuring the transmitter’s menus and display screens to the measured parameter. The X80 is designed with a durable stainless steel enclosure for explosion proof/exd hazardous applications.
-
product
Benchtop/Portable Cable/Harness Wiring Test System
CKT1175-10
Designed for wiring testing requirements requiring up to 2,000 test points, the CKT1175-10 is ideal as a benchtop or portable test system. The system is packaged in an enclosure specifically designed to be used in rugged environments. The basic 500 test point system is 20.5 in. (521 mm) wide X 12.0 in. (305 mm) high X 16.05 in. (408 mm) deep; the 500 test point expansion units are 20.5 in. (521 mm) wide X 6.00 in. (153 mm) high X 16.05 in. (408 mm) deep.
-
-
product
Visual Fault Locators
Visual fault locators are used to identify problems with your fiber. GAOTek visual fault locators typically are applied for fiber tracing, fiber routine, and continuity checking. Imagine being able to easily identify when and where a fiber is breaking, bending, or when there’s a threat to the fiber layer.
-
product
Wiring Analyzers for Cables, Wire Harnesses, Backplanes
CableEye M2Z, M3Z, M4
With our cable testers and harness testers, find defective or miswired cables instantly before they damage equipment or waste valuable technician time. CableEye® all-in-one test and cable management systems have a unique, patented graphic wiring display to visually pinpoint problems when wiring errors are detected, and offer under a second pass/fail testing for production environments. Quickly locate intermittent connections and identify their position in the cable.
