Gold Testers
See Also: Gold Test
-
Product
Serial Bit Error Ratio Testers
-
Developing next-generation technology requires world-class signal integrity and analysis capability. Keysight offers the widest choice of serial bit error ratio test (BERT) products for accurate and efficient characterization, compliance, and manufacturing test for digital interfaces in computer, video, datacom, and telecom applications operating up to 40 Gb/s. Keysight’s breakthrough technology enables you to conquer even the most difficult measurement challenges.
-
Product
High Frequency Spark Tester
HF-15B
-
The HF-15B is a compact, digital 3kHz spark tester with a test voltage range of 500v to 15KV rms.
-
Product
Single-Functional Testers
-
Electrical installation safety testing is a wide subfield of general electrical safety testing and encompasses both troubleshooting and fault-finding in complex industrial installations and simple, often periodic testing of only specific parts of the installation. The former usually requires the use of multifunctional testing devices, while the latter can be more conveniently done by testers with far fewer test and measurement functions.
-
Product
Electronic Ballast Production Line Tester
UI2000-OK
-
• Eight windows for displaying input characteristics, output characteristics, convenient for comparison and analysis. • Frequency response for testing input current up to 1 MHz, suitable for precise testing of various kind of electronic ballast. • High speed testing, finish testing input and output characteristics within 1 minute. • Portable with built-in chip micro-processor, particular suitable for development and spot production. • Parameters, waves and curves of input, output and startup can be printed. • Communicating with PC, special software provided and both Chinese version and English version available. Run in WINDOWS3.2, WINDOW95 or WINDOWS98, nice interface between people and computer, easy to operate.
-
Product
Conventional friction and wear tester
EFM-III
-
The measurement unit of A&D's conventional friction and wear tester has been adjusted to enable the measurement of friction characteristics with higher precision.
-
Product
Avionics Data Bus Tester
Distributed CORVUS
-
Distributed CORVUS works in conjunction with CORVUS-300 to isolate bus anomalies and fault resolution. The Transmit unit, C-9235-TX, sends 1553 like data pattern through a bus stub and coupler to the Receive unit, C-9235-RX, on another stub. This will measure insertion loss, possible bit errors and correct polarity. The Receive unit can also be used to give a digital scope representation of the active data bus showing signal quality and peak to peak amplitude.
-
Product
Login Digital Epstein Tester Model
Model EP400
-
Digital Epstein Tester EP-400 is designed to measure AC magnetic properties of flat rolled magnetic materials at high frequency by using Watt-meter, Ammeter, Voltmeter and Source. Epstein bridge test method is a fundamental method for evaluating the magnetic performance of flat-rolled magnetic materials in either sheared or stress relief annealed condition. This test method is suitable for design, specification acceptance, service evaluation, and research and development.
-
Product
Auto Tensile Tester
ATT-03
-
Jinan Leading Instruments Co., Ltd.
ATT-03 Auto Tensile Tester is applicable inthe test of physical mechanical properties of plastic films, laminated materials, flexible packaging materials, plastic flexible tube, adhesives,adhesive tapes, pressure sensitive tape, adhesive bandage (plaster), releasepaper, protective film, flip off cap, foil, diaphragm, back sheet, non-woven, rubber and paper fiber, etc. It can perform the test items of tensile, peeling,deformation, tearing, heat seal, adhesive, puncture force, open force,low-speed unwinding force and unsnapping force, etc.
-
Product
AFC 45° Automatic Flammability Tester
M233G
-
To determine the burning characteristics of textiles under controlled conditions. Stainless steel test cabinet with glass observation panel provided with automatic timing of flame spread in 0.1 second increments from ignition.
-
Product
Voltage Tester, 12V to 1000V, Light
72-2980
-
Non-Contact Voltage Detector Handy accessory detects presence of AC voltage from 12V ~ 1KV, providing clear audio and visual indication. Five segment bargraph display shows relative voltage level. Built in LED flashlight provides added convenience in poorly lit environments.
-
Product
Digital Insulation Tester
200M
-
Laxtronics Instruments & Controls Pvt. Ltd
Digital insulation tester Model No: DIT200M is designed to carry out electrical insulation measurement in delicate or sensitive electronic sensors, transducers, modules and assemblies with test voltage from 1 to 30 Volts DC, its short circuit current is less than 100uA. The instrument can measure Resistance from 1 Meg Ohm to 1000 Meg Ohms.
-
Product
High Voltage Insulation Tester
505
-
Simpson's Model 505 High Voltage Insulation Tester is capable of measuring insulation resistances from 10 kilohms to 1 teraohm with eight selectable test voltages up to 5000 V. As a safety feature, the insulation tester acts as an AC/DC voltmeter to measure the absence of voltage in networks up to 2000 V.
-
Product
High Frequency Insulation Tester
HFIT 7.0
-
The MEDTEQ high frequency insulation tester is a popular device for evaluating compliance with IEC 60601-2-2 and the characteristics of insulation at high frequency
-
Product
Digital 12V Battery Tester
BT175
-
Schumacher Electric Corporation
DIGITAL TESTER FOR 12V BATTERIES/STARTER SYSTEMS/CHARGING SYSTEMSHand-held tester checks the battery, starting and charging systems with digital accuracyDigital display guides you through the testing process and shows voltage and CCALEDs indicate OK, OK & Recharge, Recharge & Retest, Weak, Bad Battery and Error For 12V SLI and VRLA/AGM/GEL batteriesAccepts rating types CCA, CA, EN, IEC, DIN and SAEOperating range: 100-1200 CCA (SAE)Testing voltage: 7-15VContents: (1) Schumacher BT175 Digital Battery Tester (1) owner's manual
-
Product
Tensile Compression Force Tester
ESM303
-
The ESM303 is a highly configurable single-column force tester for tension and compression measurement applications up to 300 lbF [1.5 kN], with a rugged design suitable for laboratory and production environments. Sample setup and fine positioning are a breeze with available FollowMeTM force-based positioning - using your hand as your guide, push and pull on the force gauge or load cell to move the crosshead at a variable rate of speed.
-
Product
Adhesion Testers
-
Adhesion testing is the best way to determine whether your films and coatings adhere to substrates the way you need them to.
-
Product
Fiber Stiffness Tester
DRK023B
-
Shandong Drick Instruments Co., Ltd.
Used to determine the bending properties of various fibers.
-
Product
6-12V Heavy Duty Circuit Tester
1651
-
Peaceful Thriving Enterprise Co Ltd
Check on 6 and 12V systems. Use on accessories including lights, starters, alternators, cooling and heating components, radios and relays.
-
Product
Dynamic Seam Fatigue Tester
TF152
-
TESTEX Testing Equipment Systems Ltd.
Dynamic Seam Fatigue Tester, to determine the strength of upholstery seam constructions covering a standard foam composite cushion by imposing a cyclic, impact and penetrating load.
-
Product
IEC60065 Socket Torque Balance Tester Torsion Tester
-
Shenzhen Chuangxin Instruments Co., Ltd.
*Plug and Socket Torque Tester/Device is for compliance is checked by engaging the device, as during intended use, with the socket-outlet of a test apparatus. *Plug Torque Tester/Equipment is a device provided with pins intended to be introduced into fixed socket-outlets shall not impose undue strain on these socket-outlets.The balancing arm of the test apparatus pivots about a horizontal axis through the centre lines of the contact tubes of the socket-outlet at a distance of 8 mm behind the engagement face of the socket-outlet.*With the machine not in engagement, the balancing arm is in equilibrium, the engagement face of the socket-outlet being in the vertical position.After the device has been engaged, the torque to be applied to the socket-outlet to maintain its engagement face in the vertical plane is determined by the position o a weight on the balancing arm.
-
-
Product
Thickness Tester
-
Shenzhen UYIGAO Electronic Technology Co., Ltd
The coating thickness gauge is designed for non-destructive, fast and precise coating thickness measurement.
-
Product
Tester For The New Digital Grid
Zeus IEC-61850
-
Zeus is a tester designed to install and maintain the communications in the power industry. It supports legacy and new generation interfaces in order to verify Ethernet / IP, PTP, SyncE, ToD, IRIG-B, T1 / E1, C37.94, RS-232, G703 and protocols such as PRP, GOOSE, SV or MMS, therefore you will get a perfect vision and control of your infrastructures improving protection and data acquisition.
-
Product
Vacuum Bottle Tester
VBT-75P S2
-
The VBT-75P S2 is Vanguard’s second generation microprocessor-based, portable 75 kV dc vacuum bottle tester. This lightweight, portable tester is designed for testing circuit-breaker vacuum bottles in the field and at the shop.
-
Product
Electricity Meters Tester
Caltest 10
-
Calmet Smart Calibration Devices
Single phase portable electricity meters tester class 0.5% powered from tested circuit with load force possibility apart from tested object. There is no need to disconnect the users during measurement
-
Product
Compact Semiconductor Tester
QST4416-FC
-
Qmax Test Technologies Pvt. Ltd.
The Qmax Model QST4416-FC is a compact small foot print, sophisticated automatic semiconductor tester. Its state-of-the-art hardware design which is freely configurable to user's application requirements and software features facilitates it to test linear & mixed signal IC components which covers a wide range of products like linear, Power management, Opto electronics, digital and mixed signal devices etc.
-
-
Product
Auto Contact Resistance Tester
KVHL
-
KV Hipot Power Test Equipment Co.,Ltd
KVHL Auto contact Resistance Tester with advanced large power switch power technology ang electric circuit is a special measurement instrument for testing the contact resistance of high/low switchs, cable wires and welds.
-
Product
Torque Tester
CD-100M/10M
-
Ideal for daily inspection of electric screwdrivers. Use conventional joints. Five channels of pass/fail judgment conditions can be saved, and settings can be made simply by switching channels even if the tightening conditions change. 3 times more durable than the conventional model, even with sudden high torque. disassemble the joint due to excessive unwinding .
-
Product
Universal Cable/Harness Tester
LX-680
-
Shenzhen Lian Xin Technology Co., Ltd.
The system provides Chinese/English free switch operation interface·Starting up conducts self-diagnosis and self-correction·The system can scan and direct automatically.·The system provides advanced instant open-circuit, short-circuit, continuity test, can test the wire break·It can function as unilateral, standard, multi-segment and spot test of wire·The maximum test voltage is AC1000V / DC1500V·The maximum test spot is 256.
