-
product
Bi-Axial or Axial Averaging Extensometers
Model 3560
Jinan Testing Equipment IE Corporation
This extensometer is ideally suited for testing anisotropic materials such as advanced composites as well as for general purpose tests like determining Poisson’s ratio. The Model 3560BIA uses a design unique to Epsilon, where the knife edges remain parallel during the displacement. This approach greatly reduces crosstalk between axes and allows use on round or flat specimens with equal ease. These extensometers are very easy to mount. Integral springs hold the unit on the test sample. The parallel multiple flexure design makes these units very durable.The Model 3560AVG reads axial strain only as a single averaged output. It may also be supplied with two independent outputs, one measurement from each side of the specimen. This set-up is most commonly required when an indication of specimen bending is desired. The second version, the Model 3560BIA, includes both the averaged axial strain and the transverse strain. Again, this may also be configured as dual independent axial readings, which results in a three channel extensometer.The Model 3560 extensometers are strain gaged devices, making them compatible with any electronics designed for strain gaged transducers. Most often they are connected to a test machine controller. The signal conditioning electronics for the extensometer is typically included with the test machine controller or may often be added. In this case the extensometer is shipped with the proper connector and wiring to plug directly into the electronics. For systems lacking the required electronics, Epsilon can provide a variety of solutions, allowing the extensometer output to be connected to data acquisition boards, chart recorders or other equipment.
-
product
Thin Film Based Thermopile Detector: 2 or 1 Channels
DR46
A two-channel or a one-channel compensated thin-film thermopile in a TO-8 package. Each active area is 4mm x 0.6mm. Offers high output with excellent signal-to-noise ratio. An internal aperture minimizes channel-to-channel crosstalk increasing sensitivity.
-
product
Performance Board For LSI Tester
Place inner layer GND plane all over. Impedance control of signal line and crosstalk prevention, etc. contribute to improvement of characteristics in various ways.
-
product
Dual 16 to 1 Terminated 50 600MHz PXI RF Multiplexer
40-765-002
This terminated dual 16 to 1 multiplexer is part of a range of RF multiplexers available in the following configurations: dual, quad and octal 4 to 1, single, dual and quad 8 to 1, single and dual 16 to 1 and single 32 to 1. All multiplexers have the option of automatic terminations which offer advantages at system level by reducing the presence of standing waves in the system which can cause degradation in isolation and crosstalk.
-
product
100 Pin Micro-D Cable, Male To Male, 1m 2-56 UNC Screwlocks, Metal Shell
A100SMR-100SMR-9B100
This 1m long male to male 100-Pin SCSI Style Micro-D Cable Assembly is constructed from 7/36 (28 AWG) Tinned Copper twisted pair wiring with Polyolefin insulation to minimise crosstalk. Screwlocks are provided to secure the connectors to their associated products. This cable assembly is suitable for use with Pickering BRIC modules that use the 100-pin Micro-D connector.
-
product
Cable 100-Pin Micro-D Male to Unterminated, Cut Ends, 0.5m 2-56 UNC Screwlocks, Metal Shell
A100SMR-C-9A050
This 0.5m long male to unterminated 100-Pin SCSI Style Micro-D Cable Assembly is suited for direct connection to various products using the 100-Pin connector. It is constructed from 100-Pin twisted pair cable with varying left and right hand lays to minimise crosstalk. The Cable is colour coded to ensure easy connection. Screwlocks are provided to secure the SCSI connector to its associated product.
-
product
Active Antenna Combiner
M2C
The M2C active antenna combiner is designed as an ideal matching component to Lectrosonics digital transmitters. Up to eight transmitters can feed a single antenna to minimize cabling in multi-channel systems. The inputs are isolated to minimize crosstalk and IM (intermodulation) between RF channels.
-
product
Cable 96-Pin Micro-D Female To Female, 2m
40-970C-096-2m-FF
The 96-Pin SCSI Style Micro-D Cable Assembly is constructed from 7/36 (28AWG) Tinned Copper twisted pair wiring with Polyolefininsulation to minimise crosstalk. Metal Spring Latches are provided to secure the connectors to their associated products.
-
product
Cable, 25 Pin 1.27mm Pitch Micro-D to 25 Pin D-Type, Female to Male, 1.8m, Economy
A025CFR-025DMR-ZA180
This economy 1.8m long female 25-Pin Micro-D to male 25-Pin D-type cable assembly is constructed from 7/36 (28 AWG) copper wiring with PVC insulation and screening to minimise crosstalk. Screwlocks are provided to secure the connectors to their associated products. This cable assembly is suitable for high density applications including connection to Pickering's LXI DIO/Trigger port.
-
product
Octal 4 To 1 Terminated 50Ω 600MHz PXI RF Multiplexer
40-761A-008
The 40-761A-008 terminated octal 4 to 1 multiplexer is part of a range of RF multiplexers available in the following configurations: dual, quad and octal 4 to 1, single, dual and quad 8 to 1, single and dual 16 to 1 and single 32 to 1. All multiplexers have the option of automatic terminations which offer advantages at system level by reducing the presence of standing waves in the system which can cause degradation in isolation and crosstalk.
-
product
Quad 8 to 1 Terminated 50 600MHz PXI RF Multiplexer
40-763-004
This 4 to 1 multiplexer is part of a range of RF multiplexers available in the following configurations: dual, quad and octal 4 to 1, single, dual and quad 8 to 1, single and dual 16 to 1 and single 32 to 1. All multiplexers have the option of automatic terminations which offer advantages at system level by reducing the presence of standing waves in the system which can cause degradation in isolation and crosstalk.
-
product
Thin Film Based Thermopile Detector: 3 Channels
TM34
A three-channel thin-film thermopile in a TO-8 package. Each symmetrically positioned active area is 3.16mm x 0.4mm. Offers low noise output and internal aperture minimizing channel-to-channel crosstalk while increasing sensitivity.
-
product
Cable 96-Pin Micro-D Female to Female, 2m
40-970B-096-2m-FF
The 96-Pin SCSI Style Micro-D Cable Assembly is constructed from 7/36 (28AWG) Tinned Copper twisted pair wiring with Polyolefin insulation to minimise crosstalk. Metal Spring Latches are provided to secure the connectors to their associated products.
-
product
Thin Film Based Thermopile Detector: 4 Channels
2M Quad
A four-channel thin-film thermopile in a TO-8 package. Each active area is 2mm x 2mm. Offers the world's highest 4-channel sensitivity with exceptional signal-to-noise performance in a TO-8 package. Internal aperture minimizes channel-to-channel crosstalk while increasing sensitivity.
-
product
In-circuit Test
i3070
The Keysight i3070 In-Circuit Test (ICT) System embodies proven technology, enhancing test efficiency through time-tested software, hardware, and programmability. Catering to diverse PCBA sizes, it addresses applications such as IoT, 5G, automotive, and energy. Its unique design minimizes undesired effects from parasitic capacitance, enhances immunity to crosstalk, and eliminates stray signal coupling, ensuring consistent and repeatable measurements.
-
product
Cable 100-Pin Micro-D Male to Unterminated, Tinned Ends, 1m 2-56 UNC Screwlocks, Metal Shell
A100SMR-T-9A100
This 1m long male to unterminated 100-Pin SCSI Style Micro-D Cable Assembly is suited for direct connection to various products using the 100-Pin connector. It is constructed from 100-Pin twisted pair cable with varying left and right hand lays to minimise crosstalk. The Cable is colour coded to ensure easy connection. Screwlocks are provided to secure the SCSI connector to its associated product.
-
product
Cable, 25 Pin 1.27mm Pitch Micro-D, Female to Unterminated, Tinned Ends, 1.8m, Economy
A025CFR-C-ZA180
This economy 1.8m long female 25-Pin Micro-D to unterminated (with tinned ends) cable assembly is constructed from 7/36 (28 AWG) copper wiring with PVC insulation and screening to minimise crosstalk. Screwlocks are provided to secure the connector to its associated product.
-
product
Quad 4 to 1 50 600MHz PXI RF Multiplexer
40-760-004
This 4 to 1 multiplexer is part of a range of RF multiplexers available in the following configurations: dual, quad and octal 4 to 1, single, dual and quad 8 to 1, single and dual 16 to 1 and single 32 to 1. All multiplexers have the option of automatic terminations which offer advantages at system level by reducing the presence of standing waves in the system which can cause degradation in isolation and crosstalk.
-
product
WaveMaster Oscilloscope, 13 GHz Bandwidth, 4 Input Channels, 40 GS/s Max Sample Rate
WaveMaster 813Zi-B
Up to 20 GHz bandwidth and 80 GS/s sample rate.The most advanced oscilloscope user interface.The industry’s only true hardware 14.1 Gb/s serial trigger.Low Jitter Measurement Floor and exceptional timebase stability.Comprehensive set of serial data analysis, debug, validation and compliance tools.Integrated 50 Ω and 1 MΩ inputs for true connection and probing flexibility.Integrated standard and custom measurements and math functions for unrivaled analysis capability.Multi-lane serial data eye, jitter and crosstalk analysis.Real-time de-embedding, emulation, and equalization.
-
product
PXI 16 x SPST Reed Relay
40-115-021
Available in normally open (DPST & SPST) configurations. Connections are made via a front panel micro-D 96-pin male connector. For applications requiring improved bandwidth and crosstalk performance please look at our 40-120 and 40-125 range of shielded reed relay cards. General purpose reed relays are suitable for the construction of small switching networks, slaving up to larger switches or operating external devices (e.g. lamps, solenoids etc.). To simplify inter-relay wiring, interconnection points are built onto the circuit board easing the construction of complicated wiring.
-
product
Family of Wavefront Sensors
ShaH
The family of fast, accurate and reliable wavefront sensors. High quality lenslet arrays optimized for reducing the subapereture crosstalk. An interface to a variety of CCD and CMOS sensors allows a wide range of acquisition bands from UV to near IR.
-
product
Cable, 25 Pin 1.27mm Pitch Micro-D, Female to Unterminated, Cut Ends, 1m
A025CFR-C-5A100
This 1m long female 25-Pin Micro-D to unterminated (with cut ends) cable assembly is constructed from 18/0.1 (26 AWG) copper wiring with PVC insulation and screening to minimise crosstalk. Screwlocks are provided to secure the connector to its associated product. This cable assembly is suitable for high density applications including connection to Pickering's LXI DIO/Trigger port.
-
product
Thin Film Based Thermopile Detector: 1 Channel
DR46 Compensated
A one-channel compensated thin-film thermopile in a TO-8 package. The active area and compensating element area are 4mm x 0.6mm each. Offers high output with very good signal-to-noise ratio. Internal aperture minimizes channel-to-channel crosstalk increasing sensitivity.
-
product
Cable 96-Pin Micro-D Female to Unterminated, Cut Ends, 1m
40-972B-096-1m-FU
The 96-Pin SCSI Style Micro-D to Unterminated Cable Assy is constructed from 28 AWG Twisted Pair Tinned Copper wire with Polyolefin insulation. Crosstalk is minimised. Wires are colour coded for easy connection. Metal Spring Latches are provided on the 96-Pin connector.
-
product
Cable 100-Pin Micro-D Male to Unterminated, Tinned Ends, 0.5m M2.5 Screwlocks
A100SMR-T-7A050
The cable assembly is suited for direct connection to various products using the 100-Pin connector. It is constructed from 100-Pin twisted pair cable with varying left and right hand lays to minimise crosstalk. The Cable is colour coded to ensure easy connection. Screwlocks are provided to secure the SCSI connector to its associated product.
-
product
Single 8 To 1 Terminated 50Ω 600MHz PXI RF Multiplexer
40-763A-001
The 40-763A-001 terminated single 8 to 1 multiplexer is part of a range of RF multiplexers available in the following configurations: dual, quad and octal 4 to 1, single, dual and quad 8 to 1, single and dual 16 to 1 and single 32 to 1. All multiplexers have the option of automatic terminations which offer advantages at system level by reducing the presence of standing waves in the system which can cause degradation in isolation and crosstalk.
-
product
Cable 96-Pin Micro-D Female to Unterminated, Tinned Ends, 0.5m
A096SFR-T-5A050
The 96-Pin SCSI Style Micro-D to Unterminated Cable Assy is constructed from 28 AWG Twisted Pair Tinned Copper wire with Polyolefin insulation. Crosstalk is minimised. Wires are colour coded for easy connection. Metal Spring Latches are provided on the 96-Pin connector.
-
product
High Temperature Axial Torsional Extensometers (1200 C or 1600 C)
Model 7650
Jinan Testing Equipment IE Corporation
Model 7650 extensometers are primarily used on round specimens tested in bi-axial test machines capable of simultaneous axial and torsional loading. All models are capable of bi-directional displacement in both axes and may be used for strain-controlled fatigue testing under fully reversed load and strain conditions at frequencies up to 10 Hz.All 7650 models mount rigidly on the load frame and incorporate slide mounting to bring the extensometer into contact with the specimen. The gauge length is set automatically before mounting on the test specimen, which allows for hot mounting after thermal equilibrium has been reached.These units are specifically designed to minimize crosstalk between axes and to provide high accuracy, high resolution measurements. They incorporate capacitive sensors for low operating force and include electronics with programmable filtering and multi-point linearization for improved performance and accuracy. The overall design minimizes, and in many cases virtually eliminates, any influence from common lab environment vibrations.These water-cooled extensometers are equipped with high purity alumina rods with conical rod tips for specimen contact when testing to 1200℃(2200°F). Silicon carbide rods are used for the 1600℃ (2900°F) high temperature option.
-
product
Multi-Axis Sensors
Multi Axis Load Cell are designed and manufactured by Interface to measure a multiple of forces and/or moments simultaneously with a single load cell sensor. These sensors provide multiple bridges that precisely measure the applied force from one direction with little or no cross-talk from the other forces or moments - when installed and used according to specifications.
-
product
Single 32 to 1, 50 600MHz PXI RF Multiplexer
40-766-001
This 4 to 1 multiplexer is part of a range of RF multiplexers available in the following configurations: dual, quad and octal 4 to 1, single, dual and quad 8 to 1, single and dual 16 to 1 and single 32 to 1. All multiplexers have the option of automatic terminations which offer advantages at system level by reducing the presence of standing waves in the system which can cause degradation in isolation and crosstalk.
