Performance Testing
determines degree of ability.
See Also: Conformance, Qualification, Benchmark, Failure Analysis
-
Product
Desktop Meter Qualification Board
2199
-
Providing complete capabilities for evaluating meters and communications performance, TESCO’s Desktop Meter Qualification Board (Catalog No. 2199) can generate any voltage and load conditions the meter may encounter in the field. Apply non-sinusoidal voltages with complex load waveforms. Perform disconnect tests and reconnect tests without having to worry about being able to drive the meter’s switches.
-
Product
Battery Pack Test Equipment For 1-2 Series Battery
TOB-W602
-
Xiamen Tob New Energy Technology Co., Ltd
1-2 Series Battery Pack Test Equipment Used For Mobile Phone Battery Performance Testing 0-10V
-
Product
20 Slot, 6U PXI Chassis
GX7000C
-
The GX7000C Series are high-performance 20-slot PXI chassis that can accommodate up to 19 instruments as well as a PXI controller (an embedded CPU or a PXI bus expander interface such as the MXI series). The 6U form-factor provides the necessary real estate to accommodate high performance and high-density test instrumentation, while offering the flexibility of being able to use 3U PXI and cPCI instruments as well.
-
Product
Chassis Dynamometer Smoke Testers
-
A chassis dynamometer smoke tester (CDST) is used to test diesel emissions when the engine is under load. This is of course a much more realistic test than the commonly used free acceleration test. It is also better for the diesel engine.During a CDST test an automatic test cycle is performed, whereby the emission is measured at different engine loads. The monitor shows checks and actions to perform before the test, shows real-time measuring data and instructions for the driver during the test, and the end results after the test.
-
Product
PXIe Vector Network Analyzer, 10 MHz To 44 GHz
M9837A
-
The M9837A PXI network analyzer (VNA) offers unrivaled performance for testing multiport, multisite, multi-DUT modulated signal measurement from 10 MHz to 44 GHz.
-
Product
PXI 18 Channel Data Comms MUX, 96-pin SCSI
40-735-902
-
The 40-735 data communications multiplexer is designed for switching the data lines of serial interfaces (RS232, USB). Careful attention to the design of the module ensures that the switching system minimizes its impact on the transmission distance of USB1.1 interfaces. The MUX is available in 36:1 or 18:1 formats and enables a single source of serial data to be switched to one of 36 or 18 devices under test. This allows the data source to load information to, or receive information from, the device under test. The 36:1 version can be software configured into two independent 18 way MUXs enabling two separate sources of serial data to be connected to separate banks of 18 devices. The module is ideal for performing bulk testing of any device that relies on a serial data communications port to load software or control the device operation. It can also be used for a variety of other applications where ever a 2-pole low power MUX is required.
-
Product
Patient Simulator
PatSim200
-
Designed to make every patient simulation, quicker. Unlike other Patient Simulators, the PatSim uses a home and recall function to easily move between tests and store your most used sequences, no more clicking and scrolling through ‘tree style’ hierarchy to perform each test. Functions: 12 lead NSR ECG simulation, Over 40 selectable Arrhythmias, Performance waveforms, Respiration simulation on lead I & II, Universal temperature simulation, Two channel IBP simulation and Fetal simulation.
-
Product
MU Cable Tester System
16814
-
The MU Locomotive Trainline/Cable Test System (MU Test System) can perform shorts testing, continuity testing, and ground-leakage testing on each of the 27 pin Multi-Unit Trainlines normally found on Freight Locomotives. The MU Test System is comprised of two identical tester units. Each unit is installed in a rugged, water resistant Pelican case. Each unit contains an MU cable receptacle that mates with a 27 pin MU jumper cable. A snap-on vinyl pouch on the outside cover of each unit provides storage for the battery charger/power adapter and the chassis test lead. The enclosure cover hinges separate from the test unit as the cover is opened; this removes the cover completely to allow free access to the MU cable receptacle and the control panel.
-
Product
AMIDA 5000 Tester
-
AMIDA 5000 is a high-end performance test system, combining analog, mixed-signal and logic with the latest test solutions. High pin count - as many as 512 smart multi-function pinframes and 128 sites. Ability to provide cost-optimized test solutions for a variety of consumer components in power management and mobile device components. This system has a higher number of parallel tests and a higher level of capability. This series of test systems provides a powerful test combination with high-speed hardware and software integration. The 5000 series test system is the best analog, mixed signal, digital IC, PA test system for engineering verification and mass production. It can be easily connected to all well-known wafer probing machines and sorters, and also supports parallel test functions. The 5000 series meets customers' needs for high-precision, high-resolution, high-reliability, user-friendly, and low-cost testing and measurement of test systems.
-
Product
LTE Emulation for End-to-End QOS Validation
IxLoad-Wireless XAir2
-
Keysight Network Applications and Security
Ixia’s XAir2 load module provides LTE user equipment (UE) emulation that enables a powerful IxLoad eNodeB Layer 1 to 7 test solution. With complex UE modeling, it offers realistic and easily-configured traffic models and call patterns. Using IxLoad’s real-world subscriber modeling, testers do not need to be protocol experts to develop test realism. From a single tool, users can perform capacity tests, detail a cell throughput, measure voice and video quality, model a wide variety of mobility scenarios.
-
Product
Rugged Data Acquisition Systems
-
Our team of engineers have decades of experience in performing structural testing in the aerospace, off highway, automotive, construction equipment, pulp & paper, and utility markets. We have used our testing expertise to develop a line of Rugged Data Acquisition (RAC) Systems that perform under harsh testing conditions.
-
Product
VLF test system
BAUR PHG 80 portable
-
Portable, high performance test generator with VLF truesinus technology. The BAUR PHG 70/80 portable VLF test systems are used for cable and cable sheath testing of medium-voltage cables of up to 50 kV and electrical equipment.* 3 voltage shapes in one device: VLF truesinus, VLF square wave and DC voltage* For medium-voltage cables of up to 50 kV operating voltage* Cable testing, fault conditioning, cable sheath testing
-
Product
15V6A Battery Pack Test System
TOB-BTS-15V6A
-
Xiamen Tob New Energy Technology Co., Ltd
8 Channels 15V6A Battery Pack Test System Laptop Battery Performance Testing. TOB-BTS-15V6A Battery tester equipment is an eight-channel battery analyzer to analyze polymer battery and cylindrical batteries from 12 mA to 6000 mA, up to 15V.
-
Product
Circuit Breaker Test System
AutoScan
-
AutoScan Circuit Breaker Test System is used for performing routine tests on circuit breakers and various other types of switchgear. This test system is designed to test vacuum circuit breakers, high voltage circuit breakers, and extra high voltage circuit breakers as per suitable standards.
-
Product
Modulation Distortion Up To 8.5 GHz
S930700B
-
S930700B enables fast and accurate active-device modulation distortion characterization under modulated stimulus condition up to 8.5 GHz. The wide dynamic range and vector error correction of the PNA-X result in an extremely low residual EVM of the test setup, so you can get a complete picture of your device’s performance without test system interference. S930700B can measure EVM, NPR, ACPR, and can decompose nonlinear signals and linear signals with the spectral correlation between input and output spectrum without doing demodulation. Integration with the PNA-X SCCM provides quick modulation distortion measurements while making other VNA measurements.
-
Product
Digital Oscilloscopes
-
Whether you are a hobbyist, an educator, a developer, or are debugging, performing compliance tests, you need proven measurement technology to be successful. From basic measurements to deep-analysis, UNI-T digital oscilloscopes are built on the same, proven UNI-T technology with product range from MSO oscilloscopes to portable form. You are sure to find the right oscilloscope with an unprecedented price.
-
Product
LXI Function Card Carriers
ProDAQ 6100 Series
-
Ethernet-based LXI is changing the way engineers and scientists perform test and measurement and data acquisition. As more and more PCs ship without expansion slots, customers are faced with the problem of replacing their test and measurement and data acquisition equipment. Bustec believes in the power of distributed systems and the use of IEEE standards.
-
Product
Industrial Tester
-
Ensures products, materials, or systems meet quality, safety, and performance standards by performing tests like voltage checks, mechanical stress tests, or functional simulations, using specialized equipment or manual methods to identify defects and ensure reliability in manufacturing, construction, and technology sectors, often for electrical, data, or material integrity.
-
Product
Automatic Compression Testing Machine
CTEN Series
-
Jinan Testing Equipment IE Corporation
This series compression testing machine is mainly designed for compression test of building material items, such as concrete cube, concrete blocks, cement specimen, and bricks etc, also used for compression performance test of rubber pad and top forge test of metal. With new design idea and advanced technology, this series have more advantages in appearance, operation & applications. It is the ideal test equipment for quality control at industry & mineral enterprises, education in high schools, and technology researches at scientific institutes
-
Product
Avionics Communications Test
-
Astronics communications test sets for aircraft keep your radio, wireless, and navigation communications running at peak performance. Write test program sets once and deploy them instantaneously everywhere – whether your test set is in the factory, at the depot, or in facility operation.Deployed globally for nearly 20 years, Astronics communications testers deliver the dependability you require to ensure critical communications safety and security.
-
Product
Combined Temperature and Altitude Environmental Test Chamber
-
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell’s Altitude & Temperature Test Chamber combine Altitude and temperature to test various components and products, especially the aircraft avionics. Automatic controlled vacuum system provide a precise altitude simulated condition up to 30000 meters. Available to connect cable for the electronic performance test.
-
Product
Consulting & Training
-
For the performance of EMC testing laboratories the reliability of test results is a major concern. Therefore the knowledge of uncertainty calculations is an important issue.
-
Product
Motor Winding Ohmmeter
RMO-M Series
-
The motor/generator winding resistance test is used to identify open windings, shorts between two windings, short to grounds, connection mistakes or shorted turns. This non-invasive test of winding resistance helps to pinpoint problems regarding windings in stator or rotor part of an electrical machine. Additionally, motor winding ohmmeter has the capability of performing heat run test which will show a change in windings resistance with an increase of temperature.The RMO-M series is designed as an ideal aid in preventive maintenance of electrical motors and generators. They are powerful (up to 100A of test current), portable (8 kg) and generate DC current which is completely ripple-free. This makes measurement very precise with 0,1% accuracy.Three voltage channels make measurement very easy since it is possible to obtain a value of all three winding resistances in one measurement
-
Product
Functional Testing
-
TestOrigen Software Testing Services Pvt Ltd.
Functional testing is a very important process for amplifying the quality of the software development life cycle. Functional testing mainly shows black box testing, which evaluates a particular IT product with the specific functionalities that indicate its specification. Therefore, to promote competencies and to convey a great product, it is necessary to perform a functional testing process.
-
Product
Communication Protocol Test Harness
-
Simulate Master or Outstation Devices.Monitor Communications.Create Custom Functional Tests with any .NET programming language, Python, or Tcl/Tk scripts.Exercise a device as it will be used on the utility SCADA network.Automatically Perform Conformance Test Procedures.
-
Product
Modulation Distortion Up To 125 GHz
S930712B
-
S930712B enables fast and accurate active device modulation distortion characterization under modulated stimulus conditions up to 125 GHz. The wide dynamic range and vector error correction of the PNA-X results in an extremely low residual EVM of the test setup, delivering you a complete picture of your device’s performance without test system interference. S93072B measures EVM, NPR, ACPR, and decomposes nonlinear signals and linear signals with the spectral correlation between input and output spectrum without doing demodulation. Integration with the PNA-X SCCM provides quick modulation distortion measurements while making other VNA measurements.
-
Product
Flexible Cable Assembly
WCBA-WC0129M.29M1
-
Warison provides wide range of wireless passive coaxial components, includes Adapters, Attenuators, Coaxial Cables Assemblies, DC Blocks, Filters, Isolators & Circulators, Probes & Terminations. With outstanding capability of development and design, Warison is able to custom the spec based on customer��s demand. All Warison��s products pass inspection and electronic performance test before shipping out. It is our principal to deliver the best solution to all our clients.
-
Product
PXIe-2515, 35-Channel, 0.25 A PXI Signal Insertion Switch Module
780587-15
-
PXIe, 35-Channel, 0.25 A PXI Signal Insertion Switch Module—The PXIe‑2515 is a multiplexer switch module that enables connectivity by routing high-speed digital I/O (DIO) signals between a device under test (DUT) and an NI high-speed DIO device or a parametric measurement device. You can use modules such as PXI Source Measure Units (SMUs) and PXI Digital Multimeters (DMMs) with high-speed digital devices. With the PXIe‑2515, you can perform parametric tests on digital pins without external connectivity or impedance mismatch challenges.
-
Product
Memory Tester
RAMCHECK LX DDR3
-
Quickly test DDR3 DIMM and SO-DIMM memory. In just seconds, RAMCHECK LX will perform a thorough test of the module and provide complete identification. Also tests expensive LRDIMM modules.
-
Product
Melt Flow Testers
-
nstron®'s CEAST Melt Flow Testers are specifically designed for easy and accurate measuring of the Melt Flow Rate (MFR) and the Melt Volume Rate (MVR). CEAST Melt Flow Testers range from systems that perform a simple manual test procedure to semi-automated testing systems performing multiple weight tests. Our testers meet ASTM and ISO standards.
