Serial
a bus that can be used with almost any device transmitting a single stream of data.
See Also: Bus, Parallel, I2C, LIN, Can bus, ExpressCard, Fieldbus, FireWire, RS-232, RS-485, PCI Express, Serial ATA, Serial Peripheral Interface, SMBus, Serial Analyzers, Serial Digital Interfaces, Serial Communications, Serial Data
-
Product
Power Supply QP305E 2x30V/5A
-
*On / Off switch output section*4 independent regulated DC output*Independent serial and parallel output*Constant voltage and current*Low ripple and noise*Four digit LED displays three*16 hours at full loadd
-
Product
Mixed Signal Oscilloscope - 200 MHz, 4 Analog Plus 16 Digital Channels
MSOX4024A
Oscilloscope
200 MHz4 analog plus 16 digital channels Easily view signals on the large 12.1-inch capacitive touch screen Isolate signals in seconds with exclusive Zone touch triggering Capture more data with 4 Mpts memory and standard segmented memory See more signal detail with 1,000,000 wfms/s update rate Expand your measurement capabilities with full upgradability: Add bandwidth, dual-ch 20 MHz arbitrary Wave Gen, 3-digit DVM, serial trigger and analysis & mask testing at any time
-
Product
Serial Parallel Interface
Model 2303
-
* 2303 Board provides 40 high-power TTL I/O lines that can sink 23 mA or source 24 mA. * Easily interfaces to TTL or CMOS signals and contact closures. * User can configure the data bytes as inputs or outputs.* Transfer data as bits, bytes as data strings or transparently.* Dual Serial headers support conections with baud rate switch inputs or to a Serial Flat Ribon Cable Assembly. * Optional Relay Driver board drives 24-40 relays. * 114732 Board has the DIN connector on circuit side for use with the X3DVR Relay Driver Board or for piggyback mounting.* All other specifications are the same as listed above for the 2303.
-
Product
2 Channels, MIL-STD-1553, Dual Redundant, Transformer Coupled, Assisted Mode Capable (AMC)
FTB
-
MIL-STD-1553 is a military standard published by the United States Department of Defense that defines the mechanical, electrical, and functional characteristics of a serial data bus. It was originally designed for use with military avionics, but has also become commonly used in spacecraft On-Board-Data-Handling (OBDH) subsystems, both military and civil. It features a dual, redundant, balanced-line, physical layer; a (differential) network interface; time division multiplexing; half-duplex command/response protocol; and up to 31 remote terminals (devices).
-
Product
Universal Programmers
-
Xeltek engineers work around the clock to maintain the largest device library in the industry, so new devices are being added on a daily basis for EPROM, Paged EPROM, Parallel and Serial EEPROM, FPGA Configuration PROM, FLASH memory (NOR), BPROM, NVRAM, SPLD, CPLD, EPLD, Firmware HUB, Microcontroller, and MCUs. The majority of SuperPro universal programmers come equipped with a ZIF socket supporting up to 144 pins for programming a wide range of DIP devices; other chip package supported includes SDIP, PLCC, JLCC, SOIC, QFP, TQFP, PQFP, VQFP, TSOP, SOP, TSOPII, PSOP, TSSOP, SON, EBGA, FBGA, VFBGA, uBGA, CSP, and SCSP.
-
Product
Serial Module
DS-MPE-SER4M
-
The DS-MPE-SER4M is a rugged, low cost 4-port high speed PCIe MiniCard module that is ideal for serial I/O expansion in embedded and OEM applications.
-
Product
cRIO-9036, 1.33 GHz Dual-Core CPU, 1 GB DRAM, 4 GB Storage, Kintex-7 70T FPGA, Extended Temperature, 8-Slot CompactRIO Controller
783849-01
Embedded Controller
1.33 GHz Dual-Core CPU, 1 GB DRAM, 4 GB Storage, Kintex-7 70T FPGA, Extended Temperature, 8-Slot CompactRIO Controller - The cRIO-9036 is a rugged, fanless, embedded controller that you can use for advanced control and monitoring applications. This software-designed controller features an FPGA, a real-time processor running the NI Linux Real-Time OS, and embedded user interface capability. You also can use the Mini DisplayPort to add a local human machine interface (HMI) for application development. The cRIO-9036 features an SDHC slot and a variety of connectivity ports, including two tri-speed RJ-45 Gigabit Ethernet, two USB host, one USB device, and two RS-232 serial. Additionally, the cRIO-9036 supports an extended temperate range. The registered trademark Linux® is used pursuant to a sublicense from LMI, the exclusive licensee of Linus Torvalds, owner of the mark on a worldwide basis.
-
Product
ATCA Rear Transition Module
ART104
-
The ART104 is a Rear Transition Module (RTM) that brings expandability to Vadatech’s ATC104 carrier board. The ART104 is a passive RTM that allows for Management 10/100Mbit Ethernet, Management RS-232 serial interface and PCIe x4 lanes for expansion.
-
Product
ARINC 818 Switch IP Core
-
ARINC 818-2 is a point-to-point, serial protocol, high bandwidth, low latency protocol for the transmission of uncompressed video, audio, and data during blanking period, widely used in AVIONICS application. Since a vast portion of the newer applications of the ARINC 818-2 have several displays with many channels of ARINC 818-2, switching has turned out to be more imperative. ARINC 818-2 switch can support up to 12 channels. Multiple switching modes such as broadcast, unicast, multicast, and mixed are also supported.
-
Product
Universal Safety- & Function Tester
GLP2-BASIC
-
The variety of features, e.g. to create your own test sequences, to enter your own data as serial number, result storage, freely configurable label print out, barcode function and many more leave nothing to be desired.
-
Product
Modbus Transmitter for LPPHOT01 Probe
LPPHOT01S
-
The transmitter LPPHOT01S converts the mV analog signal generated by the illumination probe LPPHOT01 into a digital signal suitable to be transmitted over a serial line RS485 with MODBUS-RTU protocol.
-
Product
Air Core Electric Arc Furnace Reactors
-
Arc Furnace Reactors are serially connected reactors that are installed in the supply systems of arc furnace transformers to stabilize arc and limit the unstable arc furnace current and voltage drop which optimize their melting process. These buffer reactors are connected in series to the primary side of the furnace transformer. Typically these reactors are tapped coils and manufactured as per customer'stap requirements.
-
Product
AXIe Logic Analysis & Protocol Test
-
Keysight's AXIe Modular Logic Analysis and Protocol test modules and powerful analysis software provide essential capabilities for engineers working on fast digital designs and chipsets using high speed parallel and serial buses, such as DDR and PCI Express Gen 3.
-
Product
500 MHz 4 Channels Oscilloscope
DSOX3054A
Oscilloscope
500 MHz4 analog channels Easily view your signals on the 8.5-inch WVGA display Capture more data with up to 4 Mpts memory See more signal detail with 1,000,000 wfms/s update rate Expand your measurement capabilities with full upgradability: Add bandwidth, memory, digital channels, 20 MHz arbitrary waveform generator, 3-digit voltmeter, serial trigger and analysis, segmented memory & mask testing at any time
-
Product
Bit Error Rate Tester
iBERT Series
-
Provide a range of signal conditioning and BER analysis from 1.5 Gb/s to 40 Gb/s on 1-4 channels and deliver the test and measurement industry''s broadest serial communications test portfolio of bit error rate tester products.
-
Product
2-Channel 500 MHz A/D and 2-Channel 800 MHz D/A with Virtex-6 FPGA - XMC
Model 71650
-
- Complete radar and software radio interface solution- Supports Xilinx Virtex-6 LXT and SXT FPGAs- Two 500 MHz 12-bit A/Ds- One digital upconverter- Two 800 MHz 16-bit D/As- Up to 2 GB of DDR3 SDRAM or 32 MB of QDRII+ SRAM- Sample clock synchronization to an external system reference- Front panel clock/sync bus for multimodule synchronization- PCI Express (Gen. 1 & 2) interface up to x8 wide- VITA 42.0 XMC compatible with switched fabric interfaces- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
Current Transformer Testers
-
Vanguard Instruments Company, Inc.
Performs CT excitation, current-ratio, polarity, and phase angle testsMeasures insulation resistance and winding resistance of the CT seconday windingsMeasures the CT's secondary burdenTest record header information including company, substation name, circuit ID, manufacturer, CT serial number, operator name, and test record-commentsBuilt-in 4.5-inch wide thermal printerPlot Multiple Saturation CurvesStores up to 128 CT test plans and 140 test records internallyUSB, Bluetooth, and USB Flash drive interface
-
Product
TTL to RS232 Adapter
SKU-012-XX
-
The TTL to RS-232 adapter connects the Serial UART to the standard RS-232 port for testing and monitoring functionality. The Adapter facilitates ease of use and helps to reduce board space and cost.
-
Product
8-Port RS232 Async Serial Communications Adapter PMC
2229
-
The Technobox 8-Port Async Communication adapter provides eight 16550-based UARTs using RS232 signaling levels. Each port provides the full set of data and modem control lines configured for DTE
-
Product
High-Speed 4-TAP USB 2.0 JTAG Controller
USB-1149.1/4E
Controller
The USB-1149.1/4E is a high-performance plug-and-play IEEE-1149.1 Boundary-Scan (JTAG) controller for the Universal Serial Bus (USB 2.0). The USB-1149.1/4E is a high-speed device compliant with Revision 2.0 of the USB Bus Specification.
-
Product
LinkExpert Software
-
LinkExpert enables complete control and management of Teledyne LeCroy's family of Protocol Analyzer and Exerciser hardware. LinkExpert provides a convenient interface to run Compliance, Conformance and Validation tests on PCI Express (PCIe) and SAS (Serial Attached SCSI) links. The LinkExpert software interface is provided free of charge and includes as standard, several validation tests for PCIe Hosts (Root Complexes) and Devices (End Points).
-
Product
Carousel Autosamplers
-
The carousel platform is designed to be sturdy, reliable, and easy to use. The rotating sample tray minimizes space requirements, making it easy to fit into an existing housing. It holds up to 96 samples when fully loaded and contains a microprocessor that allows sequential or random sampling. The autosampler is typically interfaced to and controlled by the host instrument computer using a serial, USB, or IEEE-488 parallel communications cable.
-
Product
NRZ Analysis for Signal Integrity Studio, WavePulser 40iX High-Speed Interconnect Analyzer
WAVEPULSER-SI-STUDIO-NRZ
-
Signal Integrity (SI) Studio uses SDA Expert (SDAX) serial data analysis software options to simplify NRZ or PAM serial data jitter, eye diagram, noise and crosstalk measurement and analysis setup.
-
Product
Serial to Relay Interface Boards
Model 2364 OEM
-
* 114521-11 Board provides 16 low-level form A contacts (SPST).* Provides 8 isolated inputs for CMOS, TTL and 32 Vdc signals.* Multiple relay programming modes switch individual relays or san with single or multi-pole contacts.* Fully IEEE-488.2 and SCPI compliant.* Serial interface header includes RS-232 and RS-485 signals. * GPIB interface header includes GPIB address switch input signals.* Includes 50-pin mating relay connector and serial header connector.* Optional 115750 Terminal Board for easy connections without soldering.* Operates on 12 to 24 Vdc power.* Use an ICS GPIB Connector/Address Switch Assembly to mount a GPIB connector and Address Switch on the rear panel.
-
Product
PCI-8432, 4-Port, PCI, Isolated, RS232 Serial Interface Device
779145-01
Interface
The PCI‑8432/4 is a high-performance interface for high-speed, port‑to‑port isolated communication with RS232 devices. The PCI‑8432/4 features high-performance DMA transfers, multithreading, and multiprocessor support. NI … serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
Product
MACC Protocol Converters
-
Introducing the ultimate solution for effortless communication between different protocols - our state-of-the-art MACC II protocol converter.This powerful device allows you to easily translate messages between MIL-STD-1553, ARINC-429, Ethernet, Serial and more, ensuring compatibility and reliability in your aerospace and defense systems.With its advanced features and user-friendly interface, our protocol converter is the perfect solution for aircraft manufacturers, avionics designers, and military system integrators. It offers accurate and efficient data transfer, making it ideal for use in a wide range of applications such as aircrafts, ground vehicles, and naval vessels.Our protocol converters, both rugged, to withstand harsh environments, and standard, for the lab, are fully customizable to meet your specific needs. Its compact and lightweight design makes it easy to install and integrate with other systems.Don't let communication protocol limitations hold you back - Upgrade your systems today and experience the difference!
-
Product
14-slot PICMG 1.3 Bus Passive Backplane
FAB101
-
The FAB101 features one CPU card slot and thirteen 32bit/33MHz PCI slots, and built in a 24-pin ATX power connector and 8-pin connector for thermal detected board. Furthermore, the FAB101 delivers outstanding system performance through high-bandwidth interfaces such as Serial ATA and USB 2.0 high speed peripheral (optional function). It is designed for all of PICMG 1.3 single board computers, and is a perfect fit for AXIOMTEK's SHB100 & SHB110, which are built around the PICMG 1.3 form factor. We also have various 4U-high enclosures, AX6156E, AX6156LE, AX6156LLE, AX6156LLES, AX61400, AX61491, and AX6145, to house the FAB101 and any customer's industrial integrations flexibly.
-
Product
SparkFun Breakout
FT231X
-
Introducing the SparkFun FT231X Breakout board, complete with the full UART hardware handshake feature! The pin-out of this board matches the FTDI cable to work with official Arduino and cloned Arduino boards. It can also be used for general serial applications.
-
Product
LAN⇔RS-422/RS-485 Conversion
SI-65A
-
SI-65A is an interface converter to connect factory automation equipment and analyzers, which only have the serial communication ports for RS-422/485, to LAN.
-
Product
High Speed Links
HSL
-
ADLINK's Intelligent Remote Data Acquisition & Control Modules (NuDAM) are designed for data acquisition systems based on PCs and other processor based equipment with standard serial I/O ports (RS-232 or RS-485 with auto direction control).
