TRMS Digital Multimeters
Read accurately in almost any situation and over a wider frequency range.
-
Product
Low Thermal Input Cable
34102A
-
Use this 1.2-m shielded, 4-conductor connector only with the 34420A Micro Ohm Meter; terminated in copper spade lugs.
-
Product
PXI 32 Channel Switch Simulation Module
40-480-221
-
The 40-480 is designed to simulate the operation of automotive switches where dirty contacts or leaking current can be expected from switch contamination. It allows automotive I/O devices to be tested for correct operation under adverse conditions. The design includes protection circuits that ensure module damage cannot be caused by wiring faults or UUT failures. Each module can support up to 32 channels and is suitable for both 12V and 24V automotive applications.
-
Product
PCIe RazorPlus Express 16-Bit Digitizer
-
The GaGe RazorPlus Express CompuScope is a dual-channel 16-bit digitizer supporting A/D sampling rates up to 500 MS/s with up to 250 MHz input bandwidth.
-
Product
PXI/PXIe High Density Digital Input Module, 128-Channel, 50V
40-414-101
-
The 40-414-101 (PXI) and 42-414-101 (PXIe) are 128-channel digital input modules with 50 V inputs and provide a convenient way of determining the status of input lines by comparing the input voltage with two threshold voltages - quickly establishing if the input is low, high or in an intermediate logic state.
-
Product
PCIe Digital Waveform Acquisition with Programmable Threshold - 720 MBit/s Internal Sampling Rate Timing, 700 MBit/s External State Clock
M4I.7730-X8
-
The M4i.77xx-x8 series digital waveform acquisition (logic-analyzer) cards include versions with 32 synchronous channels, either single-ended with programmable threshold levels or differential. The large onboard memory can be segmented to record different waveform sequences. While the M4i.77xx cards have been designed using the latest technology they are still software compatible with the drivers from earlier Spectrum digital acquisition cards. Therefore existing customers can use the same software they developed for a 10 year old 60 MS/s digital input card also for an M4i.77xx series 720 MS/s logic analyzer.
-
Product
PXIe-6548, 200 MHz, 32-Channel PXI Digital Waveform Instrument
781012-03
-
PXIe, 200 MHz, 32-Channel PXI Digital Waveform Instrument—The PXIe‑6548 is a digital waveform generator and analyzer for interfacing and basic characterization test with 32 single-ended digital pins. The device is capable of sampling digital waveforms at up to 200 MHz and interfacing with user-programmable voltage levels that have a 100 mV resolution. The PXI‑6548 also features advanced synchronization capabilities for building integrated mixed-signal test systems, hardware comparison for bit-error test, and per-bank digital timing features.
-
Product
EMX-75XX
-
The EMX-75XX Series adds to AMETEK VTI Instruments' growing PXI Express (PXIe) Core Automated Test Equipment (ATE)TM family as a high-current, high-density digital input/output line of modules. Unlike many static I/O PXIe modules on the market today, the EMX-75XX Series can sink or source up to 300 mA on each channel. Delivering beyond just 2 V and 5 V, engineers can program the cards to support a wide range of voltages and more—on every channel, for both input and output.
-
Product
PXIe-6570, 100 MVector/s, PXI Digital Pattern Instrument
785283-01
-
100 MVector/s, PXI Digital Pattern Instrument—The PXIe‑6570 is designed for semiconductor characterization and production test. It includes the Digital Pattern Editor for configuring pin maps, specifications, levels, timing, and patterns. The PXIe‑6570 also includes debugging tools like Shmoo, digital scope, and viewers for history RAM, pin states, and system status.
-
Product
PXI IF Digitizer
-
PXI IF Digitizers offer onboard signal processing (OSP), which enables features such as quadrature digital downconversion (DDC), real digital downconversion, and anti-alias filtering. Models include a high dynamic range front end and a highthroughput PXI Express interface, which allows them to stream IF data to disk for hours at the full sample rate. You can also choose a PXI IF Digitizer that can convert IF signals to I/Q data, so you can use this model as a standalone IF digitizer or as part of a Vector Signal Analyzer.
-
Product
Ethernet/LXI digitizerNETBOX 16 Bit Multi-purpose Digitizer - 125 MS/s on 16 Channels, 80 MS/s on 32 Channels, 32 Single-Ended Inputs, 16 True Differential Inputs
DN6.596-32
-
The digitizerNETBOX DN6.59x series allows recording of up to 48 synchronous channels with sampling rates of 20 MS/s up to 125 MS/s. These products offer outstanding A/D features both in resolution and speed as a remote instrument. The powerful A/D amplifier section offers 6 different input ranges, programmable offset and a software switching from single-ended (full number of input channels) to true differential (half number of input channels).
-
Product
32-Ch Isolated Digital I/O USB Module
USB-4750
-
Compatible with USB 1.1/2.0Bus-powered16 isolated DI and 16 isolated DO channelsHigh voltage isolation on all channels (2500 VDC)High sink current on isolated output channels (200 mA/Channels)Supports 5 ~ 60 VDC isolated input channelsInterrupt handling capabilityTimer/Counter capabilitySuitable for DIN-rail mountingOne lockable USB cable for secure connection included
-
Product
PXI-6514, 64-Channel, ±30 VDC, 32 Sink/Source Inputs, 32 Source Outputs, Bank-Isolated PXI Digital I/O Module
778965-01
-
64-Channel, ±30 VDC, 32 Sink/Source Inputs, 32 Source Outputs, Bank-Isolated PXI Digital I/O Module—The PXI‑6514 is an industrial digital I/O interface with eight banks of isolated channels. With programmable power-up states, you can configure the initial output states in software to ensure safe operation when connected to industrial actuators. If a computer or application fault occurs, the PXI‑6514 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions. Programmable input filters eliminate glitches/spikes and provide debouncing for digital switches/relays through a software-selectable digital filter.
-
Product
PXI I/O Board
MZ-TrigIO
-
The MZ Trigger I/O Board (MZTIO) is a break-out board for the Pixie-16 PXI chassis backplane providing real-time access to Pixie-16 logic signals.
-
Product
PCI-6518, 32-Channel, ±30 V, 16 Sink/Source Inputs, 16 Source Outputs, Bank-Isolated Digital I/O Device
779084-01
-
The PCI-6518 is an industrial digital I/O interface, with two banks optically isolated channels. The device is ideal for industrial control and manufacturing test applications. The PCI-6518 module is an industrial digital I/O interface, with eight banks of isolated channels. You can wire each input bank in a source or sink configuration. With programmable power-up states, you can configure the initial output states in software, to ensure safe operation when connected to industrial actuators. If a computer or application fault occurs, the PCI-6518 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions.
-
Product
USB-6525, 16-Channel, 60 V, 8 Solid-State Relays, 8 Inputs, Ch-to-Ch Isolated Digital I/O Device
779640-01
-
The USB-6525 is an industrial, bus-powered USB I/O device that can automate even the most demanding applications. The solid-state relay outputs are ideal for controlling pumps, valves, motors, and various other industrial actuators. The USB-6525 features channel-to-channel isolated digital inputs that you can use to read from industrial digital sensors, and eight solid-state relay outputs featuring 60 VDC/30 Vrms switching voltage and 500 mA per channel maximum switching current. Using programmable power-up states, you can configure the initial output states in software to ensure glitch-free, safe operations when connected to industrial actuators.
-
Product
PXI 64-Channel Digital Output Module
40-412A-021
-
The 40-412A-021 (PXI) and 42-412A-021 (PXIe) are 64-Channel Digital Output modules with high output voltage and current capability. The outputs can be used for high or low drive and each channel is capable of sourcing 0.5A from the high side or 0.5A sink on the low side. Accidental operation of both high and low side driver on the same channel is prevented by the supplied driver. Outputs are fully protected against over-voltage, over-current and thermal overload, ensuring robust and reliable operation in the toughest test environments. For high side driving, the voltage source is supplied externally, allowing the module to drive high capacity loads separate from the chassis power supply. For low side driving, the external source is not used and the module’s output operates an open collector or open drain driver.
-
Product
PXIe-6548, 200 MHz, 32-Channel PXI Digital Waveform Instrument
781012-02
-
PXIe, 200 MHz, 32-Channel PXI Digital Waveform Instrument—The PXIe‑6548 is a digital waveform generator and analyzer for interfacing and basic characterization test with 32 single-ended digital pins. The device is capable of sampling digital waveforms at up to 200 MHz and interfacing with user-programmable voltage levels that have a 100 mV resolution. The PXI‑6548 also features advanced synchronization capabilities for building integrated mixed-signal test systems, hardware comparison for bit-error test, and per-bank digital timing features.
-
Product
NI-5752B, 50 MS/s, 12-Bit, 32-Channel, Kintex-7 FPGA Support, Digitizer Adapter Module for FlexRIO
784062-01
-
The NI‑5752B is a digitizer adapter module that, when combined with a PXI FPGA Module for FlexRIO, creates a high-speed digitizer that simultaneously samples 32 channels at 50 MS/s. You can use the NI‑5752 to do real-time processing and streaming of analog data with high-performance A/D converters. The Digitizer Adapter Module for FlexRIO is ideal for applications that require in-line data processing, high data streaming rates, and deployed high-performance solutions. The NI‑5752B is compatible only with PXI FPGA Modules for FlexRIO that have Kintex‑7 FPGAs.
-
Product
Dynamic Digital I/O with Per Channel Programmable Logic Levels and PMU PXI Card
GX5295
-
The GX5295 offers outstanding digital test capabilities and channel density in a compact 3U PXI form factor. Offering both performance digital and analog test capabilities, the GX5295 provides a cost-effective, tester per pin architecture - making this card the ideal choice for high throughput, mixed-signal component test applications. Each digital channel can be individually programmed for a drive hi, drive lo, sense hi, sense lo, and load value (with commutation voltage level). In addition, each channel offers a parametric measurement unit (PMU) providing users with the capability to perform parallel DC measurements on the DUT (device under test).
-
Product
PXIe Digitizer: 100 MSa/s, 14 bit, 100 MHz
M3100A
-
The M3100A PXIe digitizer is ideal for general purpose digitizer automated test requirements. It offers high channel density with an advanced data acquisition systems (DAQ). The optional real-time sequencing, inter-module synchronization, and graphical FPGA programming software tools expand its capability to enable a number of solutions including angle of arrival (AoA), baseband electronics designs, wireless device manufacturing and multi-channel coherent signal acquisition.
-
Product
16-Ch Isolated Digital Input And 16-Ch Isolated Digital Output EtherCAT Remote I/O Module
AMAX-4830
-
Suitable for EtherCAT networks16-ch digital input and 16-ch digital output with 2,500 VDC isolationWide input voltage range (10 ~ 30 VDC)Wide output voltage range (5 ~ 40 VDC) and high output current (350 mA/ch)Quick removable European type connectorLED indicators for I/O statusSupports EtherCAT Distributed Clock (DC) mode and SyncManager modeTwo Rotary switches for up to 256 slave IDs
-
Product
Ethernet/LXI digitizerNETBOX 16-Bit Multi-purpose Digitizer - 5 MS/s on 24 Channels
DN6.591-24
-
The digitizerNETBOX DN6.59x series allows recording of up to 48 synchronous channels with sampling rates of 20 MS/s up to 125 MS/s. These products offer outstanding A/D features both in resolution and speed as a remote instrument. The powerful A/D amplifier section offers 6 different input ranges, programmable offset and a software switching from single-ended (full number of input channels) to true differential (half number of input channels).
-
Product
Multi-Channel 10-Bit Digitizer
ADQ8-8C
-
With compact modular form factors, 8 channels per board, and high-precision multi-board synchronization capabilities, ADQ8-8C is ideal for massive multi-channel implementations.
-
Product
NI-6585, 200 MHz, 32 LVDS-Channel Digital I/O Adapter Module for FlexRIO
781071-01
-
200 MHz, 32 LVDS-Channel Digital I/O Adapter Module for FlexRIO—The NI-6585 is a digital I/O adapter module that, when combined with a PXI FPGA Module for FlexRIO, creates a digital instrument for interfacing with 32 low-voltage differential signaling (LVDS) digital pins. A digital I/O adapter module for FlexRIO can be used to do real-time interfacing of standard protocols and implement customized protocols. The NI-6585 can operate at up to 200 MHz clock rates and includes support for common LVDS voltages.
-
Product
PXI Digital I/O Module With Power Distribution - With DC-DC Converter
40-228-001
-
The 40-228 provides 32 channels of digital input and 32channels of digital output, together with switched +12V,+5V, +3.3V and -12V supply outputs derived from the PXI backplane. The module is available fitted with a DC-DC converter (40-228-001) which provides an additional -5Vsupply output. Alternatively the module can be supplied with an industry standard footprint for a DC-DC converter(40-228-002) allowing the user to fit one of their own specification if required. The 40-228 includes a breadboard area that allows users to add their own circuitry to the module.
-
Product
64-Channel Boundary Scan Digital I/O Scan Module
JT 2111/MPV DIOS DIN
-
The JT 2111/MPV is a 64 channel boundary-scan digital I/O scan module enclosed in an impact resistant housing. The module is designed to test and control edge connectors, on-board connectors and logic clusters in boundary-scan applications. Multiple modules can be connected serially to increase the number of I/Os. Available with 96-pin DIN 41612 connectors and 20-pin 0.1″ pitch IDC connectors.This JT2111/MPV DIOS module is also available through our webshop.
-
Product
Ethernet/LXI digitizerNETBOX 16-Bit Multi-purpose Digitizer - 5 MS/s on 48 Channels
DN6.591-48
-
The digitizerNETBOX DN6.59x series allows recording of up to 48 synchronous channels with sampling rates of 20 MS/s up to 125 MS/s. These products offer outstanding A/D features both in resolution and speed as a remote instrument. The powerful A/D amplifier section offers 6 different input ranges, programmable offset and a software switching from single-ended (full number of input channels) to true differential (half number of input channels).
-
Product
Phi6 Drivers
-
Phi6 is the software environment to manage, control and program 6TL modules and systems.
-
Product
Ethernet/LXI digitzerNETBOX 14 Bit High Speed Digitizer - 400 MS/s on 20 Channels, 20 Single-Ended Inputs
DN6.448-20
-
The digitizerNETBOX DN6.44x series allows recording of up to 24 synchronous channels with sampling rates of 130 MS/s up to 500 MS/s. These products offer outstanding A/D features in resolution, bandwidth and speed as a remote instrument. The powerful A/D amplifier section offers six different input ranges, two input paths, AC/DC coupling and noise reduction filters.
-
Product
PXIe-5763 , 16-Bit, 500 MS/s, 4-Channel PXI FlexRIO Digitizer
785160-01
-
The PXIe-5763 is a PXI FlexRIO Digitizer that simultaneously samples four channels at 500 MS/s with 16 bits of resolution and features 225 MHz of analog input bandwidth. With over 73 dB of SNR, the PXIe-5763 is ideal for applications that require a wide dynamic range with a wideband digitizer. The FlexRIO driver includes support for finite and continuous streaming modes, and you can implement custom algorithms and real-time signal processing on the LabVIEW-programmable Xilinx Kintex UltraScale FPGA. Available in AC and DC coupled variants, the PXIe-5763 is ideal for both time and frequency domain applications, including radar prototyping, LIDAR, communications, microscopy, OCT, event detection, and particle physics.
