Stator Test
See Also: Stator
-
Product
6TL08 Benchtop Test Platform
H710008
Test Platform
The 6TL-08 base platform was designed to cover the most common testing and in-system programming (ISP) needs with a reduced initial budget. The system includes a robust manual linear push mechanism allowing a low-cost fixture strategy thanks to the exchangeable cassettesThe platform enclosure features an 8-Slot fixture receiver, compatible with VPC 90 Series Mass Interconnect Module, as well as 6TL intelligent YAVModules (YAV90MMU &YAV90059), with room for fast ISP devices, optional PXI chassis and various power supplies. A removable back panel allows easy placement of custom connectors or test auxiliary circuitry.
-
Product
Mixed Signal Battery Test System
Test System
The Mixed-Signal Battery-Test System is an automated test platform designed to meet today’s advanced battery test requirements. The platform is ideal for testing a range of battery cells and packs, and can be used in applications such as research and design, quality control, and end-of-line manufacturing. Its distributed architecture provides a scalable solution with configurable system components to accommodate specific applications.
-
Product
Component Test Fixture For N1413 With B2980 Series
N1428A
Test Fixture
The N1428A is designed to operate specifically with the B2985B / 87B electrometer / high resistance meter. It is provided with two component modules, which are used to hold SMD, lead, and various types of devices. Electrical noise effects are reduced by the employment of a shielded case. A built-in interlock circuit enables safe high-voltage measurements. The N1413A high resistance meter fixture adapter is also required to connect the N1428A to the B2985B / 87B.
-
Product
Conformance Test System
TS8980
Test System
The R&S®TS8980 is the most compact full range conformance testing solution on the market for testing in line with requirements from GCF, PTCRB and regulatory bodies. It supports the entire device certification process for RF and RRM, covering the widest range of technologies including 5G NR based on 3GPP and carrier acceptance specifications. The test system is available in various configurations to cover the required scope of testing.
-
Product
Test Platforms
Test Platform
Leverage 20+ Years of Test Industry Experience with Built-In IP for Maximum Reuse
-
Product
VITA 62, 3U Test Fixture
TF-3U-7B041-1
Test Fixture
This Power Supply test fixture is being proposed as a tool for checking Injector / Ejector operation, proper alignment of the VITA 62 connector and proper alignment of both keys on a Single slot, 3U, VITA 62/SOSA power supply.
-
Product
Active Alignment Assembly & Test Platform
Test Platform
Quickly deliver flawless camera & LiDAR modules, MEMS devices, die based sensors, LED and laser-based headlights and other high-end products with a supremely accurate standardized platform.
-
Product
JTAG Functional Test
JFT
Functional Test
JFT comprises a series of software modules that support boundary-scan test and programming activities under Python, National Instruments LabVIEW and Microsoft .NET framework. Using JFT users can create JTAG/boundary-scan test application scripts, VIs or programs for PCB assemblies and systems that control individual driver/sensor pins, groups of pins declared as variables or register bits. These applications are typically used to test logic devices or mixed signal clusters and can also be transformed into re-usable test 'modules'. Pairing JFT with JTAG CoreCommander emulative test modules gives an effective, low-cost system for performing tests through embedded device peripherals (ADCs, Memory Controllers etc..)
-
Product
Test System Optimized for High Volume Production Testing of Integrated Circuits
ETS-364 / ETS-600
Test System
The ETS-364 is a general-purpose precision analog and mixed-signal test platform designed for high volume production testing of integrated circuits; optimized for high throughput applications with a fully integrated multisite software and hardware architecture. The test system offers separate floating resources for each site, improving site isolation and measurement accuracy coupled with digital instrumentation enabling the most efficient, high-volume testing available. The system supports up to 240 analog pin channels, and offers 133 MVPS digital vector rate with up to 128 digital pin channels. Eagle's scalability includes the ability to double the capacity of an ETS-364, providing more than 480 analog pin channels and up to 256 digital I/O pin channels with the ETS-600.
-
Product
Parallel Electrode SMD Test Fixture, DC To 3 GHz
16196B
Test Fixture
The 16196B surface mount devices (SMD) test fixture offers excellent repeatability and usability, with accurate correlation up to 3 GHz. 16196 series fixtures are custom designed to fit specific SMD sizes (see table below), and provide repeatable DUT positioning with reliable contacts to enable stable measurement results, reducing the possibility of operator-induced error. Traditionally, SMD inductor evaluation up to 3 GHz has been difficult to implement. Now with the 16196 series, it’s easy to perform accurate and repeatable measurements.
-
Product
Display Driver Test System
T6391
Test System
High-resolution flat-panel displays (LCDs / OLEDs) are becoming increasingly integrated. It is common for today's display driver ICs (DDIs) to contain a multitude of logic/analog circuits to manage advanced operations including touch-sensor functions. At the same time, the rapidly growing applications of LCDs / OLEDs in mobile electronics are driving demand for DDI's with smaller sizes and greater capabilities. These factors present serious IC-testing challenges. ADVANTEST's T6391 system is designed to address these needs along with DDIs' increasing number of pins and faster interfaces.
-
Product
Scienlab Combined Battery Test Solution
SL1133A
test
Solution for testing battery cells with an output power up to ±3 kW and a voltage range up to 6 V.
-
Product
Automated Test Systems
Test System
WinSoft designs, develops and integrates automated functional test systems for use in aerospace, military, high tech and commercial applications
-
Product
200 Vdc External Voltage Bias Fixture
16065A
Test Fixture
Measure a DUT with up to +/-200 V DC bias and also measure axial/radial lead components
-
Product
4-Module ICT System, I307x Series 6
E9903G
In-Circuit Test System
Test efficiency, test system stability, and seamless equipment integration. Keysight’s i3070 Series 6 family provides those improvements built upon a proven technology foundation. With time-tested software, hardware, and programmability, the Series 6 are fully backward compatible with previous systems, and they make highly repeatable measurements.
-
Product
Wafer-Level Parametric Test
test
Wafer-level reliability engineers need to reduce test time without sacrificing measurement quality and accuracy.
-
Product
Noise Figure Analysis Using NI PXI RF Test Instruments
NI-RFmx Noise Figure
Test Instrument
Measure noise figure, gain, Y-factor, effective temperatures, hot and cold power, and moreOptimized calibration and measurement routines for multi-DUT test using Y-factor and cold sourceSupports the PXIe-5668R 26.5 GHz VSA, the PXIe-5698 26.5 GHz preamplifier, and VSTsDesigned for use with industry-standard noise sources such as the Noisecom NC346 Series
-
Product
SMD Test Fixture
16034G
Test Fixture
Perform impedance evaluation on a minimum SMD size of 0.6(L) x 0.3(W) [mm]
-
Product
ESS Performance Test System
Test System
The Energy Storage System (ESS) Performance Test System is used to evaluate, test, and certify the performance of energy storage systems up to 2MW. The system is a configurable platform with over 200 channels of simultaneously measured AC and DC voltages and currents, environmental temperatures, airflow, and communications. Intuitive software provides real-time monitoring and analysis of power, energy and efficiency to adhere with industry standards. The test system interfaces hardware such as load banks, and controls the ESS to simulate utility applications such as peak shaving and frequency regulation.
-
Product
Test System Optimized for High Throughput, Low Cost of Test for Single Site, Multi-site and Index Parallel Applications
ETS-88RF
Test System
Targeting the needs of power amplifier (PA) and front-end-module (FEM) semiconductor manufacturers, the ETS-88RF test system is aligned with the test challenges associated with these direct RF radio wave interface components. The precision with which the ETS-88RF can measure high-gain, wideband frequency performance, adjacent channel leakage and power supply efficiency makes this test system the most cost-effective alternative to bench set-ups. Teradyne routinely provides timely updates to a substantial library of RF Standards (such as 802.11xx and 3GPP) targeted for PA and FEM test.
-
Product
128 DIOs JTAG Boundary Scan Resources Unit
YAV9JTAG
Test Fixture
Boundary-scan is a widely practiced test methodology that is reducing costs, speeding development, and improving product quality for electronics manufacturers around the world. By relying on an industry standard, IEEE 1149.1, it is relatively quick, easy, and inexpensive to deploy a highly effective test procedure. In addition, today’s PCBs have little alternative because of limited access to board-level circuitry.
-
Product
ARINC-429 Module
M4K429RTx
Test Module
The M4K429RTx is an ARINC-429 multi-channel test and simulation module to be used on the Excalibur 4000 family of carrier boards. The module supports up to ten ARINC-429 channels in any combination of transmitters and receivers. Each of these channels feature error injection and detection capabilities. The receive channels allow for the storage of all selected Labels with status and time tag information appended to each word.
-
Product
PCI Express 3.0 Test Platform with SMBus Support
Test Platform
The Summit Z3-16 Test Platform with SMBus Support allows the Summit Z3-16 to act as a host emulator, and provides a general purpose test backplane and interposer for testing Gen3, Gen2 or Gen1 hosts and devices. In addition, it supports the Summit Z3-16 with SMBus Support by providing SMBus tapping connectivity.
-
Product
Modular Functional Testing Platform
OTP2
Test Platform
Functional testing is an important part of product development and manufacturing and is used to ensure quality, performance and reliability from launch to end of life. A modern, future-proof functional test system must meet many criteria in order to meet the ever-growing demands of the industry. The OTP 2 open test platform developed by LXinstruments meets the following requirements for a dynamic and highly competitive market.
-
Product
PXI Integration Platform
ATS-3100
Test Platform
The new ATS-3100 enables you to rise above the module level and shift your focus to the sophisticated test solution you’re actually building. Simply add your instruments, software, and customization to create a complete solution. Or, if you're short on time or resources, ask Astronics Test Systems to do the finishing work for you.
-
Product
Automotive Test Solutions
test
The testing and simulation systems from this division are used primarily in the automotive and automotive supplier industry. These are, for example, modular function-testing systems and diagnostic tools for automotive ECUs or bus communication systems for a wide variety of electronic components in automotive production. Electromechanical assemblies and entire car seats are also tested to ensure they function
-
Product
Test Fixture
N1295A
Test Fixture
The Keysight N1295A Device/Component Test Fixture provides a low-cost solution to quickly and easily test packaged devices and components. For more advanced packaged testing needs, the Keysight 16442B Test Fixture provides more capabilities.
-
Product
VLSI Test Systems
Test System
50/100 MHz clock rate50/100 Mbps data rate1024 I/O pins (Max :1280 I/O pins)Up to 1024 sites Parallel testing32/64 M pattern memoryVarious VI sourceFlexible HW-architecture (Interchangeable I/O, VI, ADDA,)Real parallel trim/match functionTime & frequency measurement unit (TFMU)High-speed time measurement unit (HSTMU)AD/DA test optionSCAN test option (max 1G M/chain)ALPG test option for embedded memorySTDF tools supportTest program/pattern converter(J750, D10, V50, E320, SC312, V7, TRI-6020, ITS9K)User friendly windows 7 environmentCRAFT C/C++ programming languageSW (Software) same as 3380P & 3360P
-
Product
VR/AR/MR Calibration Platform
Test Platform
AR, VR and MR device calibration is critical for product performance. Leverage Averna’s standardized alignment platform to efficiently calibrate cameras and Inertial Measurement Unit (IMU) modules with supreme accuracy. Easily customize or upgrade the base platform into the automated quality solution to best fit your manufacturing requirements.
-
Product
Functional Test
cUTS
Functional Test
Get the essentials of measurement automation to power tests of simpler PCBAs and subassemblies. compactUTS (cUTS) is a cost-effective platform for automating manual tests of devices with fewer than fifty cable-accessible test points in manufacturing environments with moderate production volume. DUT-specific electrically keyed cables make changeover quick and easy.
