BGA
Surface mount chip package, which uses solder balls for its connectors.
-
Product
Optical BGA Inspection
-
Imaging hidden solder joints of BGA, IBGA, FlipChip, CSP, CGA and SMD components
-
Product
DDR4 BGA Interposers, DDR4 DRAM X4/x8 Packages
N2114A
Interposer
The N2114A DDR4 BGA interposers provide signal access to the clock, strobe, data, address and command signals to the DDR4 BGA package for making electrical and timing measurements with an Infiniium oscilloscope. With the DDR4 JEDEC specification defined at the DRAM ballout, the BGA probe adapter provides direct signal access to BGA package for true compliance testing.
-
Product
BGA Socket And BGA Adapter Systems
-
Mill-Max's BGA Socket/Adapter Systems are used for both socketing BGA devices and interconnecting circuit boards. Systems are available to fit 1mm, .050" and .8mm grid footprints.
-
Product
DDR4 X16, 2-Wing, Small KOV, BGA Interposer For Logic Analyzers
W4636A
Interposer
The W4636A DDR4 x16 – 2 wing BGA interposer for 96 ball DDR4 DRAM is designed for data rates up to and including 2.4 Gb/s. The W4636A probes all ADD/CMD/CNTRL and partial DQ/DQS, and it is designed for minimal KOV for space limited systems under test. The W4636A is the least expensive DDR4 BGA interposer for a logic analyzer.
-
Product
DDR5 X4/x8 78-ball BGA Interposer For Use With U4164A Logic Analyzers
W5643A
Interposer
The W5643A DDR5 2-wing BGA interposer for DDR5 x4/x8 BGA DRAM probing takes full advantage of the quad sample state mode on the U4164A. The W5643A is the smallest BGA interposers for DDR5 x4/x8 DRAM capable of capturing simultaneous read and write traffic at data rates exceeding up to 5GT/s for protocol analysis and up to 4Gb/s for DQ capture. U4208A and U4209A probe/cables connect any W5643A DDR5 BGA interposer directly into the U4164A logic analyzer module using 61-pin high density zero insertion force (ZIF) connectors that attach to the W5643A BGA interposer wings.
-
Product
Test Sockets & Interposers
Silmat
-
Innovative technology platforms and multiple product families for BGA, LGA, QFN and CSP packages down to 0.3mm pitch. High frequency bandwidth > 40 GHz..
-
Product
PMC Module
PMC-CycloneII-64LVTTL
PMC Module
User Programmable Altera Cyclone II FPGA 672 BGA, EP2C35, EP2C50, EP2C70, Stand alone possibility, Single wide PMC Module, 64 LVTL, Optional User clock oscillator
-
Product
Advanced Diagnostics for ScanExpress™ JET JTAG Embedded Test Solutions
ScanExpress JET Advanced Solutions
-
ScanExpress JET advanced diagnostics add additional diagnostic resolution with fully automated analysis translating functional test results to down to the net and pin level, even with BGA packages.The seamless integration with ScanExpress JET and ScanExpress Runner as well as the ability to output ScanExpress Viewer fault reports for PCB visualization make ScanExpress JET Advanced Diagnostics a must-have tool for any JTAG test system.
-
Product
LPDDR3 178-ball BGA Interposer For Logic Analyzers
W3301A
Interposer
The W3301A LPDDR3 rigid BGA interposer for LPDDR3 178-ball DRAM enables capture of simultaneous read and write traffic at data rates in excess of 1866 Mb/s. E5406A Soft Touch probes and U4201A cables connect the W3301A LPDDR3 BGA interposer into the U4164A logic analyzer module. The W3301A LPDDR3 178-ball rigid BGA interposer allows signal access to the LPDDR3 signals critical to your debug and validation effort through a U4164A logic analyzer. The probe works in existing designs and eliminates the need for up-front planning or redesign. The probe connects directly to the balls of the DRAM using a LPDDR3 178-ball riser (included) or an optional 3rd party socket (not provided), enabling operation and acquisition of LPDDR3 signals.
-
Product
Low-power, High-performance FPGA
iCE40 LP/HX
-
*Available in three series with LUTs ranging from 384 to 7680: Low power (LP) and high performance (HX)*Integrated hard I2C and SPI cores that enable flexible device configuration through SPI*Match your preferred display to your application processor with interfaces such as RGB, 7:1 LVDS and MIPI DPI/DBI*Multi-source your image sensors by implementing flexible bridges supporting common interfaces such as HiSPi, subLVDS, LVDS and Parallel LVCMOS*Up to 128 kbits sysMEM™ Embedded Block RAM*Industry’s broadest range of 0.35 mm - 0.40 mm pitch BGAs fit in space-constrained applications
-
Product
µHELIX® Test Probes
Series S200, S300, S400, and S500
-
Test Probes for fine-pitch applications: CSP, BGA, SiP, SoC, flex-circuits, micro pcb, sub-mm center-to-center spacing, half mm, quarter mm spacing. Excellent for use in sockets, fixtures, and contactors for semiconductor testing and in coaxial installations.
-
Product
High-Throughput Film Frame Handler
MCT FH-1200
-
FH-1200™ film frame test handler is designed to handle leadless devices mounted on film frame, such as QFN, DFN, WLCSP, BGA, µBGA and eWLB packages. The FH-1200 enables high parallelism testing of post-saw IC devices at ambient temperature. It can accommodate 200 mm and 300 mm wafer rings and custom shapes onto which multiple strips can be mounted. No change kits are required regardless of package size (if same frame is used).
-
Product
Digital In-Circuit tester
MTS180/300
-
Analog in-circuit inspection and function inspection are realized on this inspection equipment. IC pin float function is standard equipment. The MTS180 is a press type jig, and the MTS300 is a vacuum type jig. In the board mounting process at the production site, electrical inspection is performed on the mounted board after component mounting, and non-defective or defective products are automatically judged. The main inspection contents are short / open inspection, analog inspection of resistors, capacitors, coils, diodes, etc., lead floating voltage measurement of QFP and BGA, Digital IC inspection, frequency measurement.
-
Product
BGA Interposer, LPDDR4 200-ball, 2-wing For Logic Analyzer, Connects To 61-pin ZIF
W6601A
Interposer
The W6601A LPDDR4 2-wing BGA interposer for LPDDR4 200-ball BGA DRAM probing takes full advantage of the quad sample state mode on the U4164A logic analyzer module it is compatible with. The W6601A is the smallest BGA interposer for LPDDR4 200-ball DRAM capable of capturing simultaneous read and write traffic at data rates in excess of 3.2 Gb/s. U4208A and U4209A probe/cables connect W6601A LPDDR4 BGA interposer directly into the U4164A logic analyzer module from 61-pin high density zero insertion force (ZIF) connectors that attach to the W6601A BGA interposer wings. Refer to the W6601A data sheet for complete list of LPDDR4 signals probed with the W6601A.
-
Product
Intel Core I Platforms
-
Embedded Mini-ITX motherboards with Intel LGA115x Socket, Mobile BGA and ULT Core™ I / Pentium/ Celeron Series Processor, Up to 65W TDPs.
-
Product
Thermal Test Vehicles
TTV
-
Thermal Engineering Associates, Inc.
Using the TTC-1002 Thermal Test Chip as a basis, TEA offers TTVs in flip-chip, bare die, BGA packages for a variety of thermal simulation, reliability, qualification, heat sink characterization, and TIM characterization activities. Selective unused balls are sequentially connected together for daisy-chain applications.
-
Product
Semiconductor Package Inspection System
-
NIDEC-READ GATS (Grid Array Testing System) series carry out open/leak circuit tests on semiconductor package (MCM/CSP/BGA).
-
Product
Buffered Analog Crosspoint Switches
-
Analog Devices buffered video crosspoint switches offer multiple configurations from 8x8 up to 32x32 channels with gain of 1 or 2 and are offered in LQFP, LFCSP, and BGA packages. These crosspoint switches can be programmed either in serial or parallel modes and are used primarily for routing high speed signals, including composite video (NTSC, PAL, SECAM) and component video (YUV, RGB) in applications such as studios, video on demand, in-flight entertainment, surveillance, and video teleconferencing.
-
Product
Silver Ball Matrix Sockets
-
SM Contact is a unique contact that has precise silver balls held together by a proprietary conductive formulation. These conductive columns (diameter optimized for 50 ohm impedance) are suspended in a non-conductive flexible elastomer substrate with a patented solid core for enhanced durability and reliable performance over time, temperature and cycles. This flexible substrate is very compliant and resilient and enables the conductive columns to revert back to original shape when the force is removed. Solutions are available for 0.25mm to 1.27mm LGA, BGA, QFN, CSP, POP, WLP and other packages. The silver ball matrix contact technology is also available with a protective plunger matrix (a gold plated copper cylinder) that sits on top of the conductive columns. This plunger matrix protects the conductive column from contamination from various solder ball interfaces. A quickly replaceable plunger matrix enables minimal downtime during final production test. The product family code for this line of sockets is SMP.
-
Product
Digital Demultiplexers
-
Advanced Science and Novel Technology, Co., Inc.
24:48 digital demultiplexer (DMUX) with SSTL1.5 input and output interfaces.Supports data rates from 1.0Mbps to 2.0Gbps.User-controllable independent internal delays for data and clock signals.1.5V I2C control interface with a user-defined 3-bit chip address.Preset function for synchronization of multiple parallel devices.Full-rate output copy of external high-speed clock input signal.Two pairs of clock divided-by-2 and synchronous clock enable outputs for supporting the tree-type demultiplexation structure.Additional synchronous clock divided-by-4 output.Dual power supply of +3.0V and +1.5V.Industrial temperature range.Low power consumption of 2.1W at 2.0Gbps.Available in custom 256-pin BGA package (13mm x 13mm x 2.5mm).
-
Product
Get Flexible, Get FlexiFLASH
LatticeXP2
-
*Up to 885 Kbits sysMEM™ embedded block RAM and up to 83 Kbits distributed RAM*sysCLOCK™ PLLs up to four analog PLLs per device that enable clock multiply, divide and phase shifting*Three to eight sysDSP blocks for high performance multiply and accumulate.*Pre-engineered source synchronous IOs for DDR/DDR2 up to 200 MHz and 7:1 LVDS interface support up to 600 Mbps*Available in csBGA, TQFP, PQFP and BGA packaging
-
Product
Test Socket Based Elastomeric Matrix Connectors
-
Z-Axis offers a wide range of high performance test sockets, which are based on our elastomeric matrix connectors, for wide range of IC packages (BGA sockets, LGA sockets, etc.), coaxical, and wafer level; and for testing high speed, digital, analog, and RF signals etc.
-
Product
X-ray Inspection System
RTX-113™
-
Glenbrook’s RTX-113 is designed for heavy production environments where X-ray is used to inspect PCBs and assembled PCBs containing advanced components such as BGA, micro BGA, QFN and other devices.
-
Product
Automatic Test System
Star-Rec
-
Test entire HDI panel at once, or step & repeat in the "feed" direction. Fastest BGA Strip test system available. Star-Rec comes standard with: * loader * board cleaner * CCD Camera Alignment * electrical test section * fail and pass re-stackers * Board Marker
-
Product
Futureproof Your Control PLD And Bridging Designs
MachXO3
-
*Up to 9400 LUTs with up to 384 I/O pins*Instant-on 1 ms boot-up with background upgrade, Hitless I/O reconfigure and dual-boot error recovery*Available with 3.3/2.5 V core or low power 1.2 V core – including additional options on 9400 LUT devices*MachXO3LF includes programmable Flash and User Flash Memory (UFM)*Available in amazingly small (2.50 x 2.50 mm, 0.4 mm pitch) WLCSP packages and BGA packages with 0.50 mm and 0.80 mm pitch
-
Product
Single Site Test Handler
3210
Test Handler
Chroma Single Site Test Handler 3210 supports various package types such as BGA series, QFP series, QFN, TSOP, and more. The handler is primarily designed for early device design and engineering validation.
-
Product
Industrial IP69K Stainless Steel Panel PCs With 11th Gen Intel® Core™ Processor
Titan2
Panel PC
- 11th Gen Intel® Core™ i5/i3 BGA type processor- 15.6”/21.5”/23.8” FHD with projected capacitive touchscreen- Full IP69K rating for dust and water ingress- Corrosion-resistant 304 stainless steel enclosure (316 for Option)- All M12 type connectors suite for harsh environments- Optional for optical bonding and high brightness (1000 nits)- Standard VESA, Yoke/Pipe mount (optional)
-
Product
11th Gen Intel® Core™ I5-Based Fanless Embedded Computer
EMP-510 Series
Box PC
- 11th Gen Intel® Core™ i5 BGA SoC processor- DDR4 SODIMM up to 64GB- FHD/4K/8K up to 4x independent displays- 2x GbE, 1x COM, 4x USB ports- M.2 2280 SSD- Wi-Fi 6/LTE compatibility
-
Product
Labelling Systems
8000BL
-
The Model 8000BL is a high volume labelling system for tray-borne devices. Equipped with tray stackers and a Zebra 90XiII label printer, the 8000BL can apply labels safely, accurately and quickly to BGAs, QFPs, TSOPs, PGAs, etc.
-
Product
HDMI/DVI Receivers
-
HDMI® receivers and DVI receivers remain in high demand for professional, consumer, and automotive video applications, with HDMI nodes constantly increasing. Analog Devices offers a range of HDMI/DVI receivers that enable high quality conversion of digital video data to formats such as HDMI, MIPI, and TTL. Applications include video distribution, gaming, and HDMI/DVI consumer device connectivity for automotive infotainment systems. Our portfolio of HDMI receivers and DVI receivers offers competitive advantages such as automotive qualification, superior HDMI/DVI equalizer performance, comprehensive audio extraction, and small packages (6 mm × 6 mm, 0.5 mm pitch BGA).
