Serial Digital Interfaces
A family of digital video interfaces standardized by SMPTE.
-
Product
Digital I/O Board
3512
-
The 3512 is an eight channel non-isolated digital I/O board with +5V tolerant 74LCX14 inputs with hysteresis and +3.3V CMOS 74LVTH125 driven outputs. Each I/O line features a series 10 ohm damping and protection resistor and a 4.7K pull up resistor to +3.3V. On power up the outputs are tri-stated, and can then be enabled on a bit by bit basis. Output high drive is 32mA @ 2.0V minimum. Output low drive is 32mA @ 0.8V maximum.
-
Product
NI-9860, 2-Port, C Series Vehicle Multiprotocol Interface Module
783703-01
-
2-Port, C Series Vehicle Multiprotocol Interface Module—The NI‑9860 is a hardware-selectable HS/FD controller area network (CAN) and/or local interconnect network (LIN) interface for developing CAN and/or LIN applications. As part of the NI‑XNET platform, the NI‑9860 works well for applications requiring high-speed manipulation of hundreds of frames and signals while taking other data acquisition measurements in the same CompactDAQ hardware platform or while performing low-level FPGA control and embedded monitoring in the same CompactRIO chassis.
-
Product
Industry Pack Carriers and Digital I/O
CPCI-IPC
-
The CPCI-IPC module provides a 3U high performance flexible I/O scheme, that supports industry standard Industry Packs™. For application requiring low cost, high density I/O or unique combinations, the CPCI-IPC is the perfect solution. The Local DSP can be used to simply move data to and from the CPCI bus or provide pre processing functions such as local PID controls, FFT’s, digital filtering, etc. Custom application software can be downloaded to the DSP via the CompactPCI bus. A very low cost, non-intelligent version is also available, CPCI-SIP.
-
Product
32-Ch Isolated Digital I/O USB Module
USB-4750
-
Compatible with USB 1.1/2.0Bus-powered16 isolated DI and 16 isolated DO channelsHigh voltage isolation on all channels (2500 VDC)High sink current on isolated output channels (200 mA/Channels)Supports 5 ~ 60 VDC isolated input channelsInterrupt handling capabilityTimer/Counter capabilitySuitable for DIN-rail mountingOne lockable USB cable for secure connection included
-
Product
Digitizer Adapter Module For FlexRIO
-
Digitizer Adapter Modules for FlexRIO can be used with a PXI FPGA Module for FlexRIO or the Controller for FlexRIO to create a high‐performance instrument with customizable firmware. With sampling rates from 40 MS/s to 3 GS/s and up to 32 channels, these modules cover a wide range of requirements for both time- and frequency‐domain applications. Digitizer adapter modules also provide digital I/O capability for interfacing with external hardware.
-
Product
100 MHz 32-CH High-Speed Digital I/O Card
PCIe-7360
-
ADLINK's PCIe-7360 is a high-speed digital I/O board with 32-CH bi-directional parallel I/O lines. Data rate up to 400 MB/s is available through the x4 PCI Express® interface. Clock rate can support up to 100 MHz internal clock or 200 MHz external clock, ideally suiting applications of high-speed and large-scale digital data acquisition or exchange, such as digital image capture, video playback and IC testing.
-
Product
Handheld Digital Multimeter, 4 digit, with IP 67
U1242C
-
The strong and solid U1240C Series handheld digital multimeters(DMMs) are the tools technicians or industrial test engineers use to perform their work confidently and efficiently. Designed for handheld users working in various environments, the U1240C series is certified to IP 67 and capable to withstand up to 3-meter (10 feet) drop to suit harsh working environments. The U1240C handheld DMM scan even work longer for you with up to 400 hours of battery life. With the built-in LED flashlight, the U1240Chandheld DMM sallow users to single-handedly illuminate test area.
-
Product
Ethernet/LXI hybridNETBOX 16 Bit Digitizer and AWG - 180 MS/s Digitizer on 2 Channels, 1.25 GS/s AWG on 2 Channels
DN2.827-02
-
The hybridNETBOX DN2.82x series internally consists of a Digitizer and an AWG that can run together or independently. That allows simultaneous data generation and data acquisition for stimulus-response tests, ATE applications, MIMO applications or closed-loop applications. Used independently, the digitizer can acquire test data in the field and the AWG can replay this test data in lab. The hybridNETBOX offers 14/16 bit resolution and is available with digitizer sampling rates of up to 500 MS/s and AWG sampling rates of up to 1.25 GS/s. The hybridNETBOX can be installed anywhere in the company LAN and can be remotely controlled from a host PC.
-
Product
PXIe 8 Bit High Speed Digitizer - 5 GS/s on 1 Channel, 2.5 GS/s on 2 Channels, 1.5 GHz Bandwidth
M4X.2233-X4
-
The 9 models of the M4x.22xx-x4 Express series are designed for the high speed data acquisition. Each of the input channels has its own A/D converter and its own programmable input amplifier. This allows the recording of signals simultaneously on all channels without any phase delay between them. The extremely large on-board memory allows long time recording even with the highest sampling rates.
-
Product
PXIe-6569, PXI FlexRIO Digital I/O Module (32-in/32-out LVDS, 8 SE, KU035)
787280-01
-
1.25 Gbit/s, Kintex Ultrascale FPGA, 64 LVDS Channel FlexRIO Digital I/O Module - The PXIe-6569 provides a digital I/O interface along with a user-programmable FPGA for flexibility to fit a variety of interfacing and application needs. This module can interface with up to 64 … single-direction low-voltage differential signal (LVDS) channels and eight bidirectional single-ended channels. You can use the PXIe-6569 for real-time interfacing of standard protocols or implementing customized protocols.
-
Product
Digital Multimeter
HMC8012
-
True RMS measurement, AC, AC + DC Simultaneous display of three measurement functions, e.g. DC + AC + statistics Measurement functions: DCV, DCI, ACV, ACI, frequency, resistance (2- and 4-wire), temperature, capacitance, diode and continuity test Mathematic functions: limit testing, minimum, maximum, average, offset, DC power, calculation of dB and dBm Data logging to internal memory or USB stick
-
Product
GPIB User Installable Interface Module
EL34GPBU
-
EL34GPBU GPIB user-installable interface (SCPI-1999, IEEE 488.2) module adds a GPIB interface to your EL30000 Series bench electronic load.
-
Product
NI-9375 , 30 V, 32-Channel (Sinking Input, Sourcing Output), 7 µs (Input)/500 µs (Output) C Series Digital Module
781030-01
-
30 V, 32-Channel (Sinking Input, Sourcing Output), 7 µs (Input)/500 µs (Output) C Series Digital Module - The NI‑9375 is a digital I/O interface that works with industrial logic levels and signals for direct connection to a wide array of industrial switches, transducers, and other devices. Each digital input line is compatible with 24 V logic levels, and all the output lines are compatible with 6 V to 30 V signals, based on the external power supply. The NI‑9375 offers isolation between the input and output banks from channel‑to‑earth ground.
-
Product
USB Modular Digital Multimeter, 5 digit
U2741A
-
The Keysight U2741A USB Modular Digital Multimeter provides a broad range of measurement functions, including temperature and frequency. The U2741A is a 5.5-digit resolution digital multimeter that is able to capture up to 100 readings/sec. It uses the common non-proprietary standard high-speed USB 2.0 interface that provides ease of connectivity allowing users to set up and configure their tests swiftly with its plug and play feature.
-
Product
78-Pin Connector To Screw Terminal Interface
GT96078
-
78-Pin Connector to Screw Terminal InterfaceTerminal board interface. Interfaces to 78 pin connector.
-
Product
Digital/Pattern/PE Card
PA32S
-
The PA32S represents a new level of performance and capabilities for PXI-based digital instrumentation. Based on the proven architecture of the PE32, the PA32S offers high performance pin electronics and an enhanced timing generator in a compact, 3U PXI form factor. Each card can function as a stand-alone digital subsystem or if required, multiple cards can be interconnected, supporting up to 512 bi-directional pins (16 boards). The PA32S also supports deep pattern memory by offering= 32 M of on-board vector memory with dynamic per pin direction control and with test rates up to 33 MHz. With new 32M capture/log memory, PA32S can capture 32 channels fail log.
-
Product
Ethernet Module
M4K-ETH
-
The M4K-ETH is an intelligent Gigabit Ethernet interface module for the multiprotocol Excalibur 4000 family of carrier boards. The module supports 10Mhz, 100Mhz and 1Ghz Full Duplex UDP/IP Ethernet.
-
-
Product
96 Sink/Source
YAV90096
-
Selectable voltage and current, comparation and measurement Drive sink or source up to 32 mA per channel Maximum voltage in output selectable from 9 to 24 VDC Possibility to use I7Os in parallel Pin voltage comparator with logic readout at fix +4VDC 10-bit resolution pin voltage measurement with CAN bus value readout Build-in editable test steps sequence (test script) Size: form G
-
Product
1.6 GSPS, 14-bit RF Digitizer
ADQ1600RF
-
The ADQ1600RF (formerly named ADQ1600) is a world-leading 14 bit digitizer. With its unique 1600 MSPS capture rate, enabled by SP Devices’ ADC interleaving technology ADX, the ADQ1600RF opens for demanding measurements such as RF/IF sampling, high resolution ultra sound imaging and high-speed data recording.
-
Product
Connector Interface, Connector Type FC - Narrow Key Way
81000NI
-
81000NI - FC/APC connector interface, good for >10000 reconnection cycles, 2.03mm (0.08") key way. (for R-keying only, narrow key way)
-
Product
sbRIO-9853, Non-Enclosed, 2-Port, High-Speed C Series CAN Interface Module
780923-01
-
Non-Enclosed, 2-Port, High-Speed C Series CAN Interface Module—The sbRIO‑9853 is a high-speed Controller Area Network (CAN) interface for developing FPGA‑based applications with the NI‑RIO driver on CompactRIO. These modules are ideal for low-level FPGA‑based control and triggering applications that are programmed using the NI LabVIEW FPGA Module. These modules also are ideal for byte-level manipulation of CAN frames in the NI LabVIEW FPGA Module. The sbRIO‑9853 is only compatible with CompactRIO systems. Non-enclosed modules are designed for OEM applications.
-
Product
NI-6581, 100 MHz, 54 Single-Ended-Channel Digital I/O Adapter Module
780565-01
-
100 MHz, 54 Single-Ended-Channel Digital I/O Adapter Module for FlexRIO—The NI-6581 is a digital I/O adapter module that, when combined with a PXI FPGA Module for FlexRIO, creates a digital instrument for interfacing with 54 single-ended digital pins. You can use the NI-6581 to do real-time interfacing of standard protocols and implement customized protocols. The NI-6581 can operate sample digital waveforms at up to 100 MHz. It includes support for common transistor-to-transistor logic (TTL) voltage levels, or other voltage references can be sourced externally using a front panel connector.
-
Product
1553 to Ethernet Converter
eNet-1553
-
eNet is a small, rugged 1553 to Ethernet appliance/converter (~200 grams and about the size of a 4 stub coupler) and offers the same advanced BC, mRT and BM functions as our cards. In addition, eNet can provide an additional independent BM mode to auto bridge (transmit) 1553 messages on user defined IP/UDP packet header. The appliance can also auto-load setup images for fast auto start-up, which would be ideal for simple RT applications that wouldn’t even need an API interface (just a standard UDP interface – usually through simple socket programming).
-
Product
COM Express Type 7 10GbE SFP+ Network Adapter Card
CEI-4x10G SFP+
-
- Support up to four 10GbE SFP+ interfaces- COM.0 R3.1 Type 7 compliant- Dedicated for Express-ID7
-
Product
Digital Synchro and Digital to Resolver
DSN-DRN
-
Computer Conversions Corporation
The DSN - DRN Series are highly reliable, miniature, narrow profile and low cost, continuously updating Digital Synchro and Digital to Resolver (AC Sine / Cosine) Converters designed for military and industrial control applications.
-
Product
Interface
R15-LPCIE
-
Abaco Systems Embedded Systems’ R15-LPCIE is the latest generation of performance and flexibility for MIL-STD-1553A/B Notice II on a low profile PCI Express module. Available in -40 to +70 temperatures (with relays) and -40 to +85 temperatures (without relays) with one or two dual-redundant channels. The R15-LPCIE includes advanced API (Application Programming Interface) software that reduces application development time.
-
Product
PXI/PXIe High Density Digital Input Module, 128-Channel, 50V
42-414-101
-
The 40-414-101 (PXI) and 42-414-101 (PXIe) are 128-channel digital input modules with 50 V inputs and provide a convenientway of determining the status of input lines by comparing the input voltage with two threshold voltages - quicklyestablishing if the input is low, high or in an intermediate logic state.
-
Product
Ethernet/LXI digitizerNETBOX 14 Bit High Speed Digitizer - 400 MS/s on 8 Channels, 8 Single-Ended Inputs
DN2.448-08
-
The digitizerNETBOX DN2.44x series allows recording of one, two, four or eight synchronous channels with sampling rates of 130 MS/s up to 500 MS/s. These products offer outstanding A/D features in resolution, bandwidth and speed as a remote instrument. The powerful A/D amplifier section offers six different input ranges, two input paths, AC/DC coupling and noise reduction filters.
-
Product
Ethernet/LXI digitizerNETBOX 16 Bit High Speed Digitizer - 180 MS/s on 8 Channels, 8 Single-Ended Inputs
DN2.447-08
-
The digitizerNETBOX DN2.44x series allows recording of one, two, four or eight synchronous channels with sampling rates of 130 MS/s up to 500 MS/s. These products offer outstanding A/D features in resolution, bandwidth and speed as a remote instrument. The powerful A/D amplifier section offers six different input ranges, two input paths, AC/DC coupling and noise reduction filters.
