Filter Results By:
Products
Applications
Manufacturers
- Pickering Interfaces Inc.
product
Modular Breakout System 8-Pin Power D-type Plugin Module for 40-193
95-193-001
The 95-193-001 Plugin Breakout Module is designed to be fitted to a PXI 40-193 Fault Insertion Switch as part of the Pickering MBoS. The Modular Breakout System is designed to Simplify HILS (Hardware In the Loop Simulation) Applications.
-
product
PXIe-7822, PXI Express Digital RIO with Kintex-7 325T FPGA
783486-01
Kintex 7 325T FPGA, 128 DIO, 512 MB DRAM, PXI Digital Reconfigurable I/O Module—The PXIe‑7822 is a reconfigurable I/O (RIO) device that features a user-programmable FPGA for onboard processing and flexible I/O operation. With LabVIEW FPGA, you can individually configure the digital lines as inputs, outputs, counter/timers, PWM, encoder inputs, or specialized communication protocols. You can also program custom onboard decision making that executes with hardware-timed speed and reliability. Each line offers software-selectable logic levels. The PXIe‑7822 supports peer‑to‑peer streaming for direct data transfer between PXI Express modules. The PXIe‑7822 is well-suited for a wide variety of applications, such as high-speed waveform generation, sensor simulation, hardware‑in‑the‑loop (HIL) test, bit error rate test, and other applications that require precise timing and control.
-
product
PXIe-8510, 6-Port PXI Vehicle Multiprotocol Interface Module
784122-01
2- or 6-Port PXI Vehicle Multiprotocol Interface Module—The PXIe‑8510 is a hardware-selectable controller area network (CAN) and/or local interconnect network (LIN) interface for developing applications with the NI‑XNET driver. The PXIe-8510 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex models and applications.
-
product
Modular Breakout System 78-Pin D-type Plugin Module for 40-525A
95-525A-001
The 95-525A-001 Plugin Breakout Module is designed to be fitted to a PXI 40-525A Signal Insertion & Monitor Matrix Module as part of the Pickering MBoS. The Modular Breakout System is designed to Simplify HILS (Hardware In the Loop Simulation) Applications.
-
product
Modular Breakout System 8-Pin Power D-type Plugin Module for 40-192
95-192-001
The 95-192-001 Plugin Breakout Module is designed to be fitted to a PXI 40-192 Fault Insertion Switch as part of the Pickering MBoS. The Modular Breakout System is designed to Simplify HILS (Hardware In the Loop Simulation) Applications.
-
product
PXIe-7846, Kintex-7 160T FPGA, 500 kS/s PXI Multifunction Reconfigurable I/O Module
784143-01
Kintex-7 160T FPGA, 500 kS/s PXI Multifunction Reconfigurable I/O Module—The PXIe‑7846 features a user-programmable FPGA for high-performance onboard processing and direct control over I/O signals to ensure complete flexibility of system timing and synchronization. You can customize these devices with the LabVIEW FPGA Module to develop applications requiring precise timing and control such as hardware‑in‑the‑loop testing, custom protocol communication, sensor simulation, and high-speed control. The PXIe‑7846 features a dedicated A/D converter (ADC) per channel for independent timing and triggering. This design offers specialized functionality such as multirate sampling and individual channel triggering, which are outside the capabilities of typical data acquisition hardware. The PXIe‑7846 also includes peer-to-peer streaming for direct data transfer to other PXI Express modules.
-
product
PCI-8513, 2-Port, Software‑Selectable/FD CAN Interface Device
780684-02
2-Port, Software‑Selectable/FD CAN Interface Device—The PCI‑8513 is a controller area network (CAN) flexible data-rate (FD) interface for developing applications with the NI‑XNET driver. NI‑XNET software-selectable CAN interfaces offer the best flexibility for CAN development with onboard transceivers for high-speed/FD, low-speed/fault-tolerant, and single-wire CAN as well as any external transceiver. The PCI‑8513 excels in applications requiring real‑time, high‑speed manipulation of hundreds of CAN frames and signals such as hardware‑in‑the‑loop simulation, rapid control prototyping, automation control, and more. The NI‑XNET device‑driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts.
-
product
USB-7845, Kintex-7 70T FPGA, 500 kS/s Multifunction Reconfigurable I/O Device
783200-02
Kintex-7 70T FPGA, 500 kS/s Multifunction Reconfigurable I/O Device - The USB‑7845 features a user-programmable FPGA for high-performance onboard processing and direct control over I/O signals for complete flexibility of system timing and synchronization. You can customize these devices with the LabVIEW FPGA Module to develop applications requiring precise timing and control such as hardware‑in‑the‑loop testing, custom protocol communication, sensor simulation, and high-speed control. The USB‑7845 features a dedicated A/D converter per channel for independent timing and triggering. This design offers specialized functionality such as multirate sampling and individual channel triggering, which are outside the capabilities of typical DAQ hardware.
-
product
PCI-8516, 2-Port, PCI, LIN Interface Device
781365-01
2-Port, PCI, LIN Interface Device—The PXI‑8516 is a Local Interconnect Network (LIN) interface for developing applications with the NI‑XNET driver. The PXI‑8516 excels in applications requiring real-time, high-speed manipulation of hundreds of LIN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move LIN frames and signals between the interface and the user program without CPU interrupts, minimize message latency, and free host processor time for processing complex models and applications.
-
product
Panel-mounted Power Amplifier(Hardware In The Loop Simulation)
PA30Bi
PA30Bi is the panel-mounted type real time simulation amplifier with three-phase current and four-phase voltage.
-
product
NI-9861, 1-Port, Low-Speed/Fault Tolerant C Series CAN Interface Module
781962-01
1-Port, Low-Speed/Fault Tolerant C Series CAN Interface Module—The NI‑9861 is a fault-tolerant Controller Area Network (CAN) interface for developing applications with the NI‑XNET driver. The NI‑9861 is ideal for applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. You can perform this manipulation while taking other data acquisition measurements in the same NI CompactDAQ hardware platform or while performing low-level FPGA control and embedded monitoring in the same NI CompactRIO chassis.
-
product
PCIe-7851, Virtex-5 LX30 FPGA, 750 kS/s Multifunction Reconfigurable I/O Device
781102-01
Virtex-5 LX30 FPGA, 750 kS/s Multifunction Reconfigurable I/O Device - The PCIe‑7851 features a user-programmable FPGA for high performance onboard processing and direct control over I/O signals for complete flexibility of system timing and synchronization. You can customize these devices with the LabVIEW FPGA Module to develop applications requiring precise timing and control such as hardware‑in‑the‑loop testing, custom protocol communication, sensor simulation, and high-speed control. The PCIe‑7851 features a dedicated A/D converter per channel for independent timing and triggering. This design offers specialized functionality such as multirate sampling and individual channel triggering, which are outside the capabilities of typical DAQ hardware.
-
product
PCI-7811, 1M Gate Virtex-II FPGA, Digital Reconfigurable I/O Device
779363-01
The PCI‑7811 is a reconfigurable I/O (RIO) device that features a user-programmable FPGA for onboard processing and flexible I/O operation. With LabVIEW FPGA, you can individually configure the digital lines as inputs, outputs, counter/timers, PWM, encoder inputs, or specialized communication protocols. You can also program custom onboard decision making that executes with hardware-timed speed and reliability. The PCI‑7811 is well-suited for a wide variety of applications, such as high-speed waveform generation, sensor simulation, hardware‑in‑the‑loop (HIL) test, custom communications protocols, bit error rate test, and other applications that require precise timing and control.
-
product
Modular Breakout System 3-Pin & 20-Pin Plugin Module
95-199-004
The 95-199-004 Plugin Breakout Module is designed to be fitted to a PXI 40-199 Fault Insertion Switch as part of the Pickering MBoS. The Modular Breakout System is designed to Simplify HILS (Hardware In the Loop Simulation) Applications.
-
product
PXIe-7821, Kintex 7 160T FPGA, 128 DIO, 512 MB DRAM, PXI Digital Reconfigurable I/O Module
783485-01
Kintex 7 160T FPGA, 128 DIO, 512 MB DRAM, PXI Digital Reconfigurable I/O Module—The PXIe‑7821 is a reconfigurable I/O (RIO) device that features a user-programmable FPGA for onboard processing and flexible I/O operation. With LabVIEW FPGA, you can individually configure the digital lines as inputs, outputs, counter/timers, PWM, encoder inputs, or specialized communication protocols. You can also program custom onboard decision making that executes with hardware-timed speed and reliability. Each line offers software-selectable logic levels. The PXIe‑7821 supports peer‑to‑peer streaming for direct data transfer between PXI Express modules. The PXIe‑7821 is well-suited for a wide variety of applications, such as high-speed waveform generation, sensor simulation, hardware‑in-‑the‑loop (HIL) test, bit error rate test, and other applications that require precise timing and control.
-
product
PXI-8511, 1‑ or 2-Port, Low-Speed/Fault Tolerant PXI CAN Interface Module
780686-02
1‑ or 2-Port, Low-Speed/Fault Tolerant PXI CAN Interface Module—The PXI‑8511 is a fault-tolerant Controller Area Network (CAN) interface for developing applications with the NI‑XNET driver. The PXI‑8511 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimize message latency and freeing host processor time for processing complex models and applications.
-
product
Modular Breakout System 50-Pin D-type Plugin Module for 40-196
95-196-001
The 95-196-001 Plugin Breakout Module is designed to be fitted to a PXI 40-196 Fault Insertion Switch as part of the Pickering MBoS. The Modular Breakout System is designed to Simplify HILS (Hardware In the Loop Simulation) Applications.
-
product
PXIe-8510, 2-Port PXI Vehicle Multiprotocol Interface Module
784121-01
2- or 6-Port PXI Vehicle Multiprotocol Interface Module—The PXIe‑8510 is a hardware-selectable controller area network (CAN) and/or local interconnect network (LIN) interface for developing applications with the NI‑XNET driver. The PXIe-8510 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex models and applications.
-
product
PCIe-7841, Virtex-5 LX30 FPGA, 200 kS/s Multifunction Reconfigurable I/O Device
781100-01
Virtex-5 LX30 FPGA, 200 kS/s Multifunction Reconfigurable I/O Device - The PCIe‑7841 features a user-programmable FPGA for high-performance onboard processing and direct control over I/O signals for complete flexibility of system timing and synchronization. You can customize these devices with the LabVIEW FPGA Module to develop applications requiring precise timing and control such as hardware‑in‑the‑loop testing, custom protocol communication, sensor simulation, and high-speed control. The PCIe‑7841 features a dedicated A/D converter per channel for independent timing and triggering. This design offers specialized functionality such as multirate sampling and individual channel triggering, which are outside the capabilities of typical DAQ hardware.
-
product
Modular Breakout System 78-Pin D-type Plugin Module
95-200-001
The 95-200-001 Plugin Breakout Module is designed to be fitted to a PXI 40-200 Fault Insertion Switch as part of the Pickering MBoS. The Modular Breakout System is designed to Simplify HILS (Hardware In the Loop Simulation) Applications.
-
product
FADEC/EEC Test Platform
The FADEC/EEC Test Platform provides a hardware in-the-loop (HIL) closed-loop test environment for dynamic and maintenance testing of full-authority digital engine control (FADEC) and electronic engine control (EEC) units of both rotary- and fixed-wing airframes. The system simulates one or more turbofan engines, including its sensors and actuators for use with the most sophisticated FADECs and EECs on the market. The system delivers repeatable, cost-effective testing in a fraction of the time needed with typical in-house simulation test systems.
-
product
Modular Breakout System 50-Pin D-type Plugin Module for 40-198
95-198-001
The 95-198-001 Plugin Breakout Module is designed to be fitted to a PXI 40-198 Fault Insertion Switch as part of the Pickering MBoS. The Modular Breakout System is designed to Simplify HILS (Hardware In the Loop Simulation) Applications.
-
product
USB-7845, Kintex-7 70T FPGA, 500 kS/s Multifunction Reconfigurable I/O Device
783200-01
Kintex-7 70T FPGA, 500 kS/s Multifunction Reconfigurable I/O Device - The USB‑7845 features a user-programmable FPGA for high-performance onboard processing and direct control over I/O signals for complete flexibility of system timing and synchronization. You can customize these devices with the LabVIEW FPGA Module to develop applications requiring precise timing and control such as hardware‑in‑the‑loop testing, custom protocol communication, sensor simulation, and high-speed control. The USB‑7845 features a dedicated A/D converter per channel for independent timing and triggering. This design offers specialized functionality such as multirate sampling and individual channel triggering, which are outside the capabilities of typical DAQ hardware.
-
product
PXI-8513, 1‑Port, Software-Selectable PXI CAN Interface Module
780688-01
1‑Port, Software-Selectable PXI CAN Interface Module—The PXI‑8513 is a software-selectable Controller Area Network (CAN) interface for developing applications with the NI‑XNET driver. NI‑XNET Software‑Selectable CAN Interfaces offer the best flexibility for CAN development with onboard transceivers for High-Speed/Flexible Data‑rate, Low-Speed/Fault Tolerant Single Wire CAN as well as any external transceiver. The PXI‑8513 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts.
-
product
Modular Breakout System 8-Pin Power D-type Plugin Module
95-191-002
The 95-191-002 Plugin Breakout Module is designed to be fitted to a PXI 40-191 Fault Insertion Switch as part of the Pickering MBoS. The Modular Breakout System is designed to Simplify HILS (Hardware In the Loop Simulation) Applications.
-
product
PXI-8513 , 2-Port, Software-Selectable PXI CAN Interface Module
780688-02
2-Port, Software-Selectable PXI CAN Interface Module—The PXI‑8513 is a software-selectable Controller Area Network (CAN) interface for developing applications with the NI‑XNET driver. NI‑XNET Software‑Selectable CAN Interfaces offer the best flexibility for CAN development with onboard transceivers for High-Speed/Flexible Data‑rate, Low-Speed/Fault Tolerant Single Wire CAN as well as any external transceiver. The PXI‑8513 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts.
-
product
Modular Breakout System 160-Pin Plugin Module
95-190B-003
The 95-190B-003 Plugin Breakout Module is designed to be fitted to a PXI 40-190B Fault Insertion Switch as part of the Pickering MBoS. The Modular Breakout System is designed to Simplify HILS (Hardware In the Loop Simulation) Applications.
-
product
Modular Breakout System 8-Pin Power D-type Plugin Module for 40-194
95-194-001
The 95-194-001 Plugin Breakout Module is designed to be fitted to a PXI 40-194 Fault Insertion Switch as part of the Pickering MBoS. The Modular Breakout System is designed to Simplify HILS (Hardware In the Loop Simulation) Applications.
-
product
Modular Breakout System Chassis Mounting Frame
95-901-001
The Modular Breakout System is designed to Simplify HILS (Hardware In the Loop Simulation) Applications. This low-cost system combines a BoB (Breakout Box) feature set with the added flexibility of an FIU (Fault Insertion Unit). By mating the FIU chassis directly to the BoB, cabling is minimized, creating a more compact reliable design and improving signal integrity.
-
product
PXI-7853, Virtex-5 LX85 FPGA, 750 kS/s PXI Multifunction Reconfigurable I/O Module
780341-01
Virtex-5 LX85 FPGA, 750 kS/s PXI Multifunction Reconfigurable I/O Module—The PXI‑7853 features a user-programmable FPGA for high-performance onboard processing and direct control over I/O signals to ensure complete flexibility of system timing and synchronization. You can customize these devices with the LabVIEW FPGA Module to develop applications requiring precise timing and control such as hardware‑in‑the‑loop testing, custom protocol communication, sensor simulation, and high-speed control. The PXI‑7853 features a dedicated A/D converter (ADC) per channel for independent timing and triggering. This design offers specialized functionality such as multirate sampling and individual channel triggering, which are outside the capabilities of typical data acquisition hardware.
