Time Domain Reflectometers
Used to locate and identify faults in all types of metallic paired cable. (tscm.com) Also known as: TDR
See Also: TDR, Time Domain, Cable TDR
-
Product
Time Domain Reflectometer (TDR) Card
PCI-3127
-
The PCI-3127 is a PCMCIA-form factor TDR that can be used to identify and locate failures in installed wiring and cable systems. The instrument can make high resolution TDR measurements on circuits up to 96,000 feet (~30km) from your Windows XP notebook computer or PC using a low-voltage non-destructive test signal.
-
Product
Mini OTDR Fiber Optic Reflectometer with VFL OPM Laser Source
MT-1300 Plus
-
Guangzhou Wanglu Communications Co., Ltd.
- Display: 3.5 inch color TFT-LCD screen- Handheld design, light weight and easy operation- Single mode: 1310/1550 nm- Dynamic range: 24 / 22dB (can test about 60 km)- Automatic measurement mode: 1310/1550 nm dual wavelength can be tested simultaneously- Applicable fiber: SM- <8m extra-short event dead zone- Wavelength: 1550nm- Up to 24dB High Dynamic Range- Distance Range: 4,8,16,32,64,128,256km- Pulse width: 3ns-10us- RJ45 cable TDR test & cable sequence test- Optical power meter, Visual fault locator, Laser source- Event Map, can display the length of the link, the type of event point and the position of break point.- USB interfaces, supporting USB stick and printer and direct cable download to PC via ActiveSync- LED light- Built-in friendly-environment lith ium battery with high capacity for over 12 hours of operating life
-
Product
Power Networks Test
TX8000
-
The TX8000 is a 6 Km range Time Domain Reflectometer housed in a rugged over moulded case being water proof to IP67 and drop resistant, designed for outdoor use, but sufficiently small and light weight for general use and may be operated using one hand. Using a 3.5-inch QVGA colour display information is clearly displayed; an illuminated keypad makes the TX8000 ideal for use in poorly lit areas.
-
Product
TX Ranger
4405200
-
The TX Ranger is a hand-held Time Domain Reflectometer (cable fault locator) with a first range of 2.5 meters combined with a 1.3 Nano second pulse width gives a blind zone of only 5 cm, it makes this the ideal product for fault location on short cable assemblies and harnesses. Small and intermittent faults can be easily identified by using the selectable gain control allowing trace amplification of up to 7 times and when set to scan lock mode the advanced noise reduction software may be selected allowing the user to select between 8,16 and 32-point trace averaging further enhancing the clarity of the trace by reducing electrical and environmental interference.
-
Product
Time Domain Reflectometer
ETDR 10A-3
-
Compact single channel precision portable easy to useTDR for fault location on balanced unloaded cables.
-
Product
Cable Testers
-
The Tester can check UTP and STP Cat 5E,6,6A and Coaxial Cable. It can ldentify and locate the distance of a open or Short Circuit. With the Multifunction Tester you can determine the Continuity and Wiring of the Cable Pattern. Comes with the Low Battery Indicator. It uses TDR ( Time Domain Reflectometer ) to measure the length and distance of the cable. LCD Backlight Display.There are 8 Remote ID available.
-
Product
TDR Concrete Cure Monitoring
-
Material Sensing & Instrumentation
MSI Time-Domain-Reflectometry (TDR) Concrete Cure Monitoring provides a new approach to cure monitoring in concrete and cementitious materials [1-7]. Using an ultrafast pulse and inexpensive capacitance sensor, our TDR system follows rotation of individual chemical states of water participating in the hydration reaction. The system monitors formation of bound-water hydration products, as well as unreacted free-water to form the hydrated state.
-
Product
Optical Fiber Ranger
-
Optical fiber ranger is test equipment that functions similar to an optical time domain reflectometer. It is used in single mode fiber test applications. The fiber optic ranger is much smaller size and lighter weight compared to the fiber optic OTDR, and it is much more cost effective. They are used in optical fiber links troubleshooting, maintenance and test.
-
Product
OTDRs and Multimeters
-
This line of instruments consisting of several models of Multimeters, TDRs and OTDRs, is dedicated to the measurement of the physical parameters of the transmission media including optical fibers and electric cables.
-
Product
OTDR
TMO350 Series
-
TMO350 series Optical Time Domain Reflectometer(OTDR) is the new generation of intelligent meter for the detection of fiber communications systems.
-
Product
Enhanced Time Domain Analysis With TDR
S96011B
-
Use S96011B to perform enhanced time domain analysis for high-speed data applications. Includes all functionality of the S96010B (TDR/TDT mode). In addition, the S96011B enables more detailed measurements and evaluations, such as eye diagram / mask modes, without adding PLTS software. Jitter and emphasis / equalization capabilities enable simulation of real-world signals and environment. The S96011B covers up to 53 GHz bandwidth. Full calibration is available and the automatic deskew ensures easy removal of fixture and probe effects. To get the best accuracy, use mechanical calibration kits or ECal with DC option (i.e. N469xD or N4433D with Option 0DC).
-
Product
8K ip Camera Tester M-IPC-450C with TVI 5.0 Audio, Wrist Design
M-IPC-450C
-
Fuzhou Metricu Technology Co Ltd
8K wrist tester M-IPC-450C supports 8K ip camera, analog camera, 8MP TVI camera, 8MP CVI camera and 8MP AHD camera. (5 in one)It also supports DC12V 3A, 48V PoE 25.5W power output, UTP cable, RJ45 TDR cable, RS485, Audio in, TVI 5.0 audio, wrist design, etc.
-
Product
Mini OTDR
FiberPal OT-8700
-
FiberPal OT-8700 series instruments, with power meter built-in, are new miniature, high performance optical time domain reflectometer which is designed as fiber troubleshooter for locating fiber connector, break and imperfections for access networks. It detects event locations along the optical fiber and displays the results on a 7” color LCD display. FiberPal OT-8700 series are light, reliable and easy to use, hence it is ideal for FTTX testing. The Application Software equipped is used for data analysis, processing and storage. With the USB Interface port, enabling FiberPal OT-8700 series to transfer test data to computer easily.
-
Product
Saluki S2110P Series PON OTDR (up to 45dB)
-
S2110P series optical time domain reflectometer can be used to test single-mode wavelengths of 1310nm, 1550nm, 1625nm and 1650nm as well as customized special wavelengths. It provides multiple optional modules, such as single wavelength, multi-wavelength and online test. S2110P series can test PON networks through even 1:128 high-port-count splitters.
-
Product
Power Networks Test
TX6000
-
The TX6000 is a hand held Time Domain Reflectometer with 11 range scales covering the range 0-6000 meters, with a 7 mater first range scale and a 0.5 meter dead zone near and far end faults are clearly displayed on its 128×64 pixel back light Liquid Crystal Display.
-
Product
Microwave Cavity Characterization
-
Material Sensing & Instrumentation
Microwave cavity characterization complements TDR Dielectric Spectroscopy in low-loss materials, providing high-resolution permittivity and loss data at specific single frequencies. Since measurements do not change significantly with frequency in low-loss materials (Kramer-Kronig relation) cavity measurement at select frequencies provides a full characterization across the RF/microwave range.
-
Product
TDR Structural Health Monitoring
-
Material Sensing & Instrumentation
MSI Time-Domain-Reflectometry (TDR) Structural-Health Monitoring probes the structural health of a composite part by propagating a fast electrical pulse along a distributed linear sensor which has been fabricated directly in the laminate. The sensor is formed from the native graphite fibers already used in composite manufacture, and constitutes zero defect. Fibers are patterned into a microwave waveguide geometry, or transmission line, and interrogated by a rapid pulse as shown below. Structural faults along the line cause distortions in waveguide geometry, producing reflected pulses similar to radar. Cracking, delamination, disbonds, moisture penetration, marcelling, and strain are all detected by propagation delay, for sensor lengths up to several meters.
-
Product
Cable Fault Locator
TX2002
-
Lowest Cost Full Specification Professional Graphical TDR Rugged Palm Top Design 350g (12oz) 5 Measurement Ranges up to 3500m (11,500ft) 50, 75 & 100 ohm Selectable Cable Impedance Built in Tone Generator for Pair Tracing & Identification Suitable for testing all Communications Cables Water & Dust Proof to IP54 Complete with tool-belt holster & test leads
-
Product
CATV Meters & Instruments
-
GAOTek offers high quality, affordable CATV meters and testers to industry engineers. These instruments are used by professionals to automatically or manually test, measure, and maintain a wide collection of systems and channels. Our products are portable and durable to ensure long operational use during everyday field use by CATV technicians. Additionally, we offer QAM analyzers, PCM channel analyzers and TDR cable fault locators.
-
Product
Electrical Circuit / Wire Harness Analyzer
ECAD System 2005
-
The ECAD System 2005 is a suite of test instruments for both lumped and distributed data for analysis of electrical circuits and/or wiring harnesses. ECAD is completely self contained, and has a built-in multimeter, impedance meter, TDR, and megohmeter.
-
Product
Demonstration Board
SAMPULSE20x2
-
The SAMPULSE20x2 is a demonstration board for the Furaxa SiGe3 30GHz sampler/pulser IC. The SIGe3 IC is a dual channel sampler pulser chip, and the SAMPULSE20x2 demonstration board contains two 2.4mm combined TDR input/output connectors, one to each sampler/pulser channel in the IC. The SiGe3 IC's two sampler outputs are then sent to to two SMA jacks, the first outputting the sample taken on the rising edge of the sampler clock, and the second containing the sample taken on the falling edge of the sampler clock. The sampler clock input, which must be a square wave, may be set to any frequency from 5MHz to 1GHz, causing the board take two pairs of samples (one on each clock edge) at rates from 5 million to 1 billion per second. A pulser clock input, which may be set to any frequency from 5MHz to 2GHz, and MUST be a square wave (preferably differential) with rise time under 100pS, causes the board to produce concurrent pulses on both of the SiGe3's I/O pins, which produce near-concurrent pulses at the two 2.4mm sampler/pulser TDR input/output connectors.
-
Product
Handheld Cable Fault Locator
TM800H
-
TM800H Handheld Cable Fault Locator adopts TDR (Time Domain Reflection), new signal process and data collection technology. It can locate the distance of cable break and mix faults accurately. TM800H can be widely used in the communication installation, maintenance and general wiring. It can troubleshoot not only the local Telco-cable, but also Network cable. Its high sampling rate makes the measurement dead zone as narrow as 1 meter. This makes it a straightforward, user-friendly test solution.
-
Product
Saluki S2106X Series OTDR (up to 45dB)
-
S2106X series optical time domain reflectometer is an upgraded version with 7 inch larger display, higher operation speed and more friendly UI. It has rich external interface, which can realize remote control through Ethernet interface or two different USB interface for external USB flash drive, printer and data communication with PC.
-
Product
Multi-function Cable Tester
NCT-100-S
-
*NCT-100-S Multi-Function Cable Tester Kit can help you quickly find network cables with OOK audio during network construction and maintenance. *Use TDR diagnostic technology to quickly and accurately locate fault points and accurately measure wiring diagrams and lines. Cable identification, etc.
-
Product
Time Domain Reflectometer / TDR
-
For testing cables and interconnects, we offer the ideal tool: A time domain reflectometer (TDR). Time domain reflectometry/transmission can be used to test network return loss (S11), propagation loss (S21), and crosstalk.Moreover, it can provide the impedance profile of an electrical channel. MultiLane supplies semi-automated solutions for the testing of direct-attach cables and TIAs.
-
Product
Time Domain Reflectometer
STEP TDRS
-
Cable Measurements: Distance, Fault Types, Distance to Faults, Impedance Readings, and Loop Resistance.
-
Product
OTDRs
-
An Optical Time Domain Reflectometer (OTDR) tests the integrity of a fiber optic cable. Using a fiber OTDR, a technician can verify splice loss, identify length, and very easily locate faults in the cable. Another use is to verify the accurate installation of a fiber optic cable when it’s newly installed. If/when problems arise or if an issue is suspected in the future, a fiber OTDR can then compare the images from the original trace to the present state of the cable.
-
Product
Time Domain Reflectometer
ETDR 10A-1
-
Compact dual channel precision full function portable easy to useTDR for fault location on balanced unloaded cables.
-
Product
Signal Integrity Test Products
RoBAT RCI
-
*TDR & TDT, Measurement Capabilities*Impedance, Skew, Backdrill measurements*Automated Optical Inspection*DC Electrical Test*Now available with 4 heads*24 port (1 port per channel) TDR/TDT unit*Future capabilities – Fully automated VNA test (4 port S-Parameter Measurement)
-
Product
Flying Probe
EnteFP-5060TDR
-
Two head TDR flying probe with rotation, max panel size: 20X24, accuracy +/25um, CCD camera alignment.
