Electrostatic Discharge Simulators
create known values of electrostatic discharge.
-
Product
Partial Discharge Tester
19501-K/19500
-
Chroma 19501-K partial discharge tester combines hipot test and PD (partial discharge) detector functions in one instrument. The device is capable of a maximum 10kV AC output with leakage current measurement range of 0.01uA and a minimum partial discharge detection of 1pC. The tester is specifically developed to test high voltage semiconductor components and high insulation materials.
-
Product
Testing And Simulation
-
Uni- and bidirectional power supplies for testing and simulating batteries, fuel cells, electric drive trains and other components.
-
Product
Modular DC Electronic Load LED Simulator
6310/A
-
Chroma Systems Solutions, Inc.
Chroma 6310A Programmable Electronic Load integrates microprocessor capabilities into each load module and mainframe to provide simple and accurate parallel operation to optimize the speed and control among multiple load modules. All load modules may be configured to work synchronously, to test multiple outputs simultaneously, thus simulating real life applications.
-
Product
Solar Simulator
-
Jiangsu Keyland Laser Technology Co., Ltd.
Features:- Beyond Class AAA performance- Stable continuous working- 8000 data collecting points- Durable flash lamp- Voice prompt- Measuring data export- Customizable for special panels
-
Product
Develop - Simulate - Validate JTAG / IJTAG based IP
NEBULA
-
You, your vendors and your customers being able to use one common interface to control and observe on-chip IP, resources and instruments. The figure below shows an example IC. The new IEEE 1149.1-2013 standard supports an init-data register for configuring the analog paramaters of I/O as well as controlling on-chip PLLs. The standard further extends this by defining in BSDL user test data registers or 'scan chains'. These registers enable the ability of generic software to control and observe mission mode IP and instruments simply by describing the register interface in BSDL.
-
Product
ARINC 429 Test & Simulation Interface for VME
VME-429
-
Avionics Interface Technologies
4, 8, 16, 32, or 64 Software Programmable Tx/Rx Channels - Programmable High/Low Speed Operation - Concurrent operation of all Tx/Rx Channels at high data rates - Full Error Injection & Detection - Rate-oriented Label Transmission - Label Selective Trigger for Capture/Filtering - IRIG-B Time Code Encoder/Decoder for Data Correlation - ANSI Application interface supporting C, C++, C#, and .net development - Device driver support: Windows, Linux, & VxWorks (others on request) - Designed for extended temperature operations - 64-bit VME - Interface (VME master & slave capability) - Front Panel and Rear I/O (P2) Available
-
Product
Class AAA Steady State Solar Simulator
-
King Design Industrial Co., Ltd.
*Lamp average life 25,000 hours (We offer 1 year warranty including lamps)!*Spectrum Mis-match Class A, without filter! *Irradiance almost no decay within 10,000 hours!*Spectrum maintains stable during power adjustment!
-
Product
Modular Breakout System for Hardware-In-Loop Simulation
-
Designed in partnership with OPAL-RT Technologies, this Modular Breakout System combines a BoB feature set with the added flexibility of an FIU. By mating the FIU chassis directly to the BoB using our plug-in modules, cabling is minimized, creating a more compact reliable design and improving signal integrity.
-
Product
USB2.0 Module With 2 CAN Bus Nodes ARINC825 Compliant For Testing & Simulation of Avionic ARINC825/CAN Bus Systems
APU825-2
System
USB2.0 module with 2 CAN bus nodes ARINC825 compliant for testing and simulation of Avionic ARINC825/CAN bus systems.
-
Product
Lightning Surge Simulators
LSS Series
-
A simulator to reproduce “High energy induced lightning noise” which is induced by potential change on the ground, or done to power lines or telephone lines as result of lightning current.This immunity test is required by major standards including IEC61000-4-5 and JEC 210/212 and is widely used in many industries.
-
Product
Satellite Simulators
-
Tampa Microwave''s satellite simulators provide a compact easy to use training and evaluation tool for satellite earth terminals. We provide a variety of models with different combinations of frequency bands, transmit/receive strength, atmospheric effects and form factors. Contact us with your requirements and we will recommend a cost effective solution.
-
Product
PXI/PXIe Battery Simulator Module, 6-Channel, 1 KV Isolation
41-752A-101
Battery Simulator
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 6-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture. The 750 V or 1 kV isolation barrier (version dependent) allows the module to be used as a lower power version of a battery stack, representative of those used for vehicle propulsion.
-
Product
Avionics Test & Simulation Software
-
Ballard CoPilot® is an intuitive, graphical software program that allows you to easily monitor, record, replay, analyze, and simulate avionics bus data. With CoPilot you can interact directly with data on multiple buses using Ballard avionics interface hardware or work with previously recorded data. This advanced program features powerful tools for development, testing, troubleshooting and maintenance of avionics equipment and systems.
-
Product
ARINC 664 Simulator & Analyzer Applications Software
F-SIM-A664
-
Avionics Interface Technologies
Software GUI Application for Operating AIT ARINC 664 Interfaces - Simulate Multiple ARINC 664 End Systems Simultaneously - Full definition of input/output VLs, input/output Sampling and Queuing message ports, & TFTP Clients & Servers - Capture & Analyze Data from Multiple Virtual Links (VLs) - Live display showing all of the detected ARINC 664 VLs and message counts - Live displays showing all of the detected source and destination message (UDP) ports - Record network data to PCAPNG for use with Wireshark - Replay Previously Captured Bus Data - Also Supports MIL-STD-1553, ARINC 429 & Data Load operations
-
Product
Fibre Channel Test & Simulation Interface for PCI
PCI-FC4
-
Avionics Interface Technologies
Supports Point-to-Point, Switched Fabric, and Arbitrated Loop topologies - Two independent Fibre Channel ports - Two SFP sockets accept fiber or copper transceivers - Each port supports 1, 2, and 4 Gbps speeds - Comprehensive decoding of FC-1, FC-2, and Upper Layer Protocol (ULP) frames - Full Error Injection and Detection - IRIG-B Time Code Encoder/Decoder for Data Correlation - In-line Port Configuration for Transparent AnalyzerSupports multiple ULPs including FC-AE-ASM, FC-AE-RDMA, FC-AE-1553, and FC-AV - Compatible with AIT’s fcXplorer GUI Bus Analyzer Software
-
Product
UE Simulator
-
With Simnovus, you get superior value as our software runs on COTS and SDR enabling you to deploy multiple test beds. You do not have to spend millions on expensive Capex.
-
Product
BOSS Simulator
-
Softdel’s BOSS Simulator is a sophisticated BACnet monitoring, debugging and simulation program that runs on any Windows® computer. It has a simple interface that is easy to use for BACnet professionals as well as novices. BOSS Simulator extends the functionality of Softdel’s BOSS Explorer by adding complex simulation and troubleshooting features, including support for A-side and B-side services, device discovery across routers and auto command generation across the entire network.
-
Product
Non-Hydraulic Steering Module Test Simulator
SMTS
-
The Steering Module Test Simulator (SMTS) from MB Dynamics is a non-hydraulic turnkey lab test system, offering accurate, reliable and repeatable in-laboratory simulations of driver, road & vehicle inputs acting on a steering system, and their associated effects on steering system performance and annoying noises. Supports troubleshooting, identification, diagnosis, and resolution of root causes of unwanted noise and other performance issues common to EPS, EPHS, EPAS, MDPS, and HPS steering systems.
-
Product
Battery Cell Simulator
BCS-LABCAR
-
The ETAS Battery Cell Simulator (BCS-LABCAR) is a Hardware-in-the-Loop system which specifically targets the signal-level test, validation, and calibration of battery management systems (BMSs). The BCS-LABCAR is a high-precision Battery Cell Simulator that emulates the behavior of individual battery cells and packs across a wide range of challenging operating conditions, e.g. cell balancing over-charging, deep discharging, or pulse operation. The system is highly modular and thus scalable to emulate battery packs from a single cell all the way up to 200 cells.
-
Product
Multi-Domain Simulation
-
Every product engineering team deals with questions in the virtual prototyping phase, many of these covering multiple engineering domains. ESI's Visual-Environment multi-domain modelling allows these teams to work together in a single user environment, around a single core compute model. This multi-domain simulation environment has the capacity to integrate all virtual prototyping problems across CAE domains. In addition, its user-friendly interface and automation features empower engineering teams to be ever more productive!
-
Product
Partial Discharge Tester
GTPD-4C
-
GTPD-4C partial discharge comprehensive tester is the new generation of digital PD measurement and analysis instrument. The instrument has a strong ability of comprehensive analysis of partial discharge and detection of partial discharge in small signal and strong interference environment. With different accessories, it can measure and locate the partial discharge in any high voltage electrical equipment. It can realize testing the transformer partial discharge by applying the voltage on the three phases simultaneously.
-
Product
Dual Port Simulator Fiber Channel PCI Module
PCI-FC4 Simulyzer
Simulator
The modules are available as a single-function board - for analysis or for simulation / data generation - but also as a full-function board for simultaneous analysis and simulation. By simply upgrading the firmware / software, a single function board can become a full function board without having to purchase new hardware.
-
Product
Single or Dual Stream MIL-STD-1553A/B Test and Simulation Module
APE1553-x-DS
-
A unique feature of AIM’s APE1553-x-DS modules is the option for the MILScope™ capability. Models APE1553-1-DS/APE1553-2-DS integrate an onboard Analogue to Digital Converter (ADC) which samples, measures and stores the MIL-STD-1553 waveform. Automatic waveform validation is performed by the users Application Software or in conjunction with AIM’s PBA.pro Databus Test and Analysis Software and Test Scripts.
-
Product
Three-Dimensional Electromagnetic Simulation Package
QuickWave-3D
-
QuickWave 3D (QW-3D), is a universal user-friendly three-dimensional electromagnetic simulation package (winner of the European Information Technology Prize in 1998) based on the conformal FDTD method and supplemented with a range of unique models for curved boundaries, media interfaces, modal excitation, and parameter extraction. Complete 3D electromagnetic simulation offer a set of various results from wide area of applications. A lot of processing/postprocessings present a complete offer of comprehensive solutions from microwave components (filters, couplers, resonators, etc.) through antennas, TDR applications, optimisation and parameters sweep to simulation of microwave heating process (with Basic Heating Module) with temperature dependent media, static, rotated or moved heated object(s), and heat transfer.
-
Product
WAN Simulator / Emulator
LANforge ICE
-
LANforge ICE emulates networks that involve limited bandwidth, latency, packet loss, and corruption. LANforge ICE tests the behaviour of devices that sit on either side of an impaired network. Reduces lab and training costs by replacing expensive WAN hardware, such as T1 and FrameRelay devices. Automates testing with various scripting features and libraries.
-
Product
Charge / Discharge Battery Testing System
-
Maximize battery lifecycle insights with HAIDA International Equipment's advanced charge/discharge testers. Our energy-efficient systems simulate real-world usage patterns, from fast charging to deep cycling, while achieving ±0.05% measurement accuracy. Supporting lithium-ion, lead-acid, and emerging chemistries, Haida’s multi-channel platforms integrate regenerative discharge technology, cutting energy costs by up to 40%. Trusted by Tier 1 suppliers, Haida delivers UL 1973-certified solutions for R&D innovation and production-line quality control.
-
Product
Engineering Simulation Services
-
Staying at the forefront of product development requires more than ambitious goals. Engineering teams also need the right expertise, resources, and support to solve complex challenges without slowing innovation.
-
Product
Simulation Tools for Analog and Power Electronics
SIMetrix
-
Complete mixed-mode simulation package providing high performance, ease of use and superior analog convergence.
-
Product
Single, Dual or Quad Stream MIL-STD-1553A/B Test and Simulation Module
APE1553-x
-
MIL-STD-1553 Test and Simulation Module for PCI Express with 1, 2 or 4 Dual Redundant channels (APE1553-1, APE1553-2, APE1553-4) plus 8 programmable discrete Input/Output channels. A unique feature of AIM’s APE1553-x module is the option for the MILScope™ capability. Models APE1553-1-DS/APE1553-2-DS integrate an onboard Analogue to Digital Converter (ADC) which samples, measures and stores the MIL-STD-1553 waveform. Automatic waveform validation is performed by the users Application Software or in conjunction with AIM’s PBA.pro Databus Test and Analysis Software and Test Scripts.
-
Product
IP / VoIP Analysis & Simulation
-
GL offers high density Ethernet/IP tester variant which includes mTOP™ 1U/2U rack mount enclosures within which PacketExpert™ portable USB units are stacked to provide high density GigE ports form factor solution for testing GigE switches, routers and network conditions.
