Quadrature Amplitude Modulation
a digital bitstream whose values are represented by adjustments in phase and amplitude of sinusoidal electromagnetic waves.
See Also: QAM, QAM Analyzers
-
Product
QAM And PCM Analyzers
-
GAOTek provides a wide range of high performance and inexpensive QAM/PCM analyzers. Quadrature amplitude modulation (QAM) and pulse code modulation (PCM) analyzers are convenient instruments with top to bottom estimations and adaptable setups. Additionally, these devices have integrated functions of analog signal generators/receivers, BERT, signaling generators/receivers, selective level meters, ring generators/ identifications, dialers, DC loop circuits (ICT, OGT), balanced bridges and reflecting bridges into solitary instruments. These analyzers are ideal for installing and maintaining digital and analog networks.
-
Product
PXI Programmable Resistor Module
-
PXI Programmable Resistor Modules are wellsuited for simulating environmental conditions in hardwareintheloop(HIL) validation. The software included provides a simple user interface that accepts inputs in units of temperature or resistance, and configures the resistance across each channel. Each module uses a 37pin DSUB connector on the front panel, as well as a 2x2 MicroFit connector for easy connection to a PXI Digital Multimeter(DMM).
-
Product
PXI Temperature Input Module
-
PXI Temperature Input Modules offer up to 32 channels of analog temperature measurements. Some models include autozero channels for offset compensation as well as open thermocouple detection to identify disconnected thermocouples, while others support 2-, 3-, or 4-wire resistance temperature detector (RTD) measurements. PXI Temperature Input Modules support both high-speed and high-resolution modes. You can program channel configurations and scale measured data into engineering units.
-
Product
LED Light Bar Module
UTC-100P-L
-
Interface: USB (Cable Length:50cm). OS Support: Windows 10 & Android. Dimensions: 160.0 x 18.5 x 9.0 mm. Operating Temperature: 0 ~ 40° C.
-
Product
IO60-DIO48 Module
IO60-DIO48
-
WINSYSTEMS’ IO60-DIO48 Module adds GPIO to embedded systems with IO60 expansion featuring 48 GPIO (General Purpose Input-Output) tolerant to 30 V DC. The SPI interface is implemented through the MACH XO2 SPI-slave EFB (Embedded Function Block) interface. Each bit of each port is implemented as a bi-directional tristate driver. Each bit of each port can also be configured and enabled to detect rising and/or falling edge events and generate a system interrupt.
-
Product
PXI High Density Multiplexer, 2-Bank, 64-Channel, 1-Pole
40-610A-003
-
The 40-610A-003 is a 2-bank, 64-channel, 1-pole MUX and is part of our range of PXI high density reed-relay based multiplexer modules. The range includes a wide choice of switching configurations which are especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems.
-
Product
PXI/PXIe Microwave Multiplexer, Dual SP4T, 6 GHz, 50 Ω, SMA, Failsafe
42-784B-102
-
The 40-784B-102 (PXI) and 42-784B-102 (PXIe) are dual failsafe SP4T 6 GHz unterminated microwave multiplexers. The 40/42-784B range is available with single, dual or triple, SP6T or SP4T multiplexers with front panel mounted or remotely mounted relays.
-
Product
PXI 2A Multiplexer, 1-Bank, 128-Channel, 1-Pole
40-614C-015
-
This 1-bank, 128-channel, 1 pole version is part of the 40-614C High Density 2A multiplexer module range that is available in 20 configurations (see Also in this Range link above). All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
Product
PXI/PXIe High Voltage Multiplexer, Triple 7-Channel, 1-Pole
40-321-102-HI
-
The 40-321-102-HI (PXI) and 42-321-102-HI (PXIe) are triple 7-channel 1-pole high voltage multiplexers capable of hot or cold switching up to 1000 V peak. They are also available in a range of bank sizes with 1 or 2 poles and channel counts between 4 and 48. High quality reed relays are used throughout.
-
Product
PXI High Density Screened Mux 49 Ch 2 Pole
40-670A-021-S-49/2
-
The 40-670A series of very high density multiplexer modules feature a wide range of switching configurations. Typical applications include signal routing in ATE and data acquisition systems. The 40-670 multiplexer may be operated as a conventional multiplexer with break-before-make action when a new channel is selected.In addition multiple channels may be simultaneously selected (not available in 1 pole mode).
-
Product
LXI Microwave Multiplexer, 50Ω 6-Channel 5-Bank 6GHz SMA
60-801-005
-
The 60-801-005 is a 6-channel, 5-bank RF multiplexer suitable for switching 50Ω signals up to 6GHz. It is part of a range of LXI Microwave Multiplexers which are available with bandwidths between 6GHz and 40GHz and support for between 1 and 16 banks of 4 or 6-channel multiplexers. It is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors.
-
Product
160-Ch 2A-250VAC 24VDC Multiplexer/Matrix
YAV90057
-
The YAV90057 is a High density multiplexer, with 10-bank, 16-channel, 1 pole. It uses high quality electro-mechanical relays allowing each channel to switch current up to 2A and voltage up to 220VDC/250VAC.
-
Product
1x8 Multiplexer Plug-In
1260-138A
-
The Astronics1260-138A is an eight 1x8, two-wire scanner/multiplexer plug-in card for the Adapt-a-Switch® platform. It installs, easily and directly from the front panel, into the Adapt-a-Switch VXI Carrier, 1260-100.
-
Product
PXI Dual 18 Channel MUX, 96-Pin SCSI Connector
40-735-912-S1
-
The 40-735 data communications multiplexer is designed for switching the data lines of serial interfaces (RS232, USB). Careful attention to the design of the module ensures that the switching system minimizes its impact on the transmission distance of USB1.1 interfaces. The MUX is available in 36:1 or 18:1 formats and enables a single source of serial data to be switched to one of 36 or 18 devices under test. This allows the data source to load information to, or receive information from, the device under test. The 36:1 version can be software configured into two independent 18 way MUXs enabling two separate sources of serial data to be connected to separate banks of 18 devices. The module is ideal for performing bulk testing of any device that relies on a serial data communications port to load software or control the device operation. It can also be used for a variety of other applications where ever a 2-pole low power MUX is required.
-
Product
PXI 5A Mux 8-Bank 5-Ch Isolated COM
40-651-014
-
This range of high density power multiplexer modules is suitable for switching inductive/capacitive loads up to 5A at 250VAC. It is available in the following 1-pole multiplexer formats: 1-bank 48-channel. 2-bank 24-channel. 4-bank 11-channel. 8-bank 5-channel.Connections are made via a front panel 50-way male D-type connector. Power multiplexer modules are intended for switching heavy AC or DC loads or for slaving up to large external relays, contactors and solenoids.
-
Product
Signal, Module, Receiver, CASS, 210 Position, J4, Right Angle PCB Mount
510113133
-
Signal, Module, Receiver, CASS, 210 Position, J4, Right Angle PCB Mount.
-
Product
PXI Dual 3-Channel 10A Solid State MUX
40-666-011
-
The 40-666 is a high current multiplexer available in dual 3-channel or single 6-channel configurations occupying two slots of PXI chassis. Each multiplexer switch uses a fully isolated solid state relay which has been designed to offer fast operation under hot switching conditions and high inrush current with no operational life degradation. Each multiplexer channel can support 10A of continuous current and switch up to 200V signals. The switches can sustain inrush currents in excess of 50A. AC or DC signals can be switched since the switch is polarity insensitive. Note: The 40-666-011 supersedes the 40-666-001 which is functionally the same but with some changes in specification. A data sheet for the 40-666-001 can be found in the40-666/667 User Manual.
-
Product
PMC Module
PMC-DA816
-
The PMC-DA816 is a slave Digital to Analog boardthat is managed by the host processor on the PMCbus. The card contains a state machine that performsmost of the work of outputting data, in order tominimize the impact to the HOST system.The PMC-DA816 is supported by ALPHI Technologyunder Windows NT by a Board Support Packagewhich is supplied with the card. Other documentationsupplied with the card will describe this support in fulldetail.
-
Product
Universal Counter/Timer
PXIe-2461
-
The Astronics PXIe-2461 is a high-performance, 2-channel, universal 235 MHz frequency interval counter. Occupying a single PXI Express peripheral slot or hybrid slot, the frequency and time interval/counter (FTIC) offers 12 easy-to-use automatic measurement functions including:
-
Product
PXI 3A Power MUX BRIC, 4-Channel, 12-Pole
40-571-301
-
The 40-571 is a Power Multiplexer designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is possible for most configurations, see switching specifications for restrictions). It is ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. It is available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts.
-
Product
LXI Microwave Multiplexer, SP4T, 11-Bank, 26.5GHz, 50Ω, SMA
60-803-311
-
Our 60-803-311 is a 11 bank terminated SP4T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 26.5GHz. The 60-803 range is capable of supporting up to 14 banks of terminated 4 channel multiplexers it is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
Product
LXI 96-Channel 1GHz Video Multiplexer
60-721A-004
-
The 60-721A High Performance Video MUX is designed for the switching of RF signals in 75 Ohm systems at frequencies up to 1GHz. It is ideal for 75 Ohm monitoring applications that require a multiplexer to select one channel to be routed to measuring equipment.
-
Product
PXI/PXIe Microwave Multiplexer, Dual SP6T, 50GHz, 50Ω, SMA-2.4
40-785C-552-T
-
The 40-785C-552-T (PXI) and 42-785C-552-T (PXIe) are dual SP6T 50GHz microwave multiplexers with automatic termination of unused signals. The 40/42-785C range of multiplexers are available as single or dual, SP6T or SP4T panel mounted multiplexers with relays mounted on the front panel. The single slot version can support up to three supplied remotely mounted multiplexers.
-
Product
PXI Synchronization Module
-
PXI Synchronization Modules use the trigger bus, star trigger, and system reference clock features of PXI to implement advanced multi-device synchronization. By using PXI Synchronization Modules, you can improve measurement accuracy, implement advanced triggering schemes, and synchronize multiple devices to act as one for high-channel-count applications.
-
Product
32-CH EtherCAT I/O Terminal Base For M-Type Modules
ECAT-TB32-M-DIN
-
The ECAT-TB32-M-DIN is a 32-channel EtherCAT I/O Terminal Base designed specifically for ADLINK's M-Type EtherCAT IO Slave Modules. This terminal base unit serves as a foundational component for enabling communication and interaction with various peripheral devices through the EtherCAT protocol.
-
Product
4G DDR4-3200 512X16 1.2V SAM -20~85℃
AQD-SD4U4GN32-SP2
-
SAM Original Chip, Industrial Design for Improved Reliability, PCB: 30μ gold finger. Anti-sulfuration, Semi Wide-temp Support -20~85℃.
-
Product
PXI/PXIe MEMS Optical MUX, 8-Channel, Multi-Mode, 50/125 Fiber
40-852A-318-M50
-
The 40/42-852A-318-M50 is a PXI/PXIe 8-channel multiplexer with MU (mini SC) connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
Product
LXI Microwave Multiplexer, SP4T, 11-Bank, 50GHz, 50Ω, SMA-2.4
60-803-611
-
Our 60-803-611 is a 11 bank SP4T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 50GHz. The 60-803 range is capable of supporting up to 16 banks of 4 channel multiplexers it is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
Product
Micro Coax/Micro Power, Module, Receiver, 90 Series, 120 Positions
510104270
-
Primary mating module 510108263.*Please note: VPC receiver modules must be separated into two pieces in order to extract contacts. For detailed instructions please consult the user manual/procedure sheet for this module before extracting contacts.
-
Product
PXI/PXIe 1000Base-T1 Dual Multiplexer With Fault Insertion, Single Channel
40-204-001
-
The 40-204-001(PXI) and 42-204-001 (PXIe) are single channel differential multiplexers designed to simulate common faults on high-speed two wire communication interfaces such as 1000Base-T1. They are available with support for 1 or 2-channels of two wire serial interfaces. Each channel pair can be looped out to external equipment or the switches can be used simulate a channel open fault. Using the fault bus, switches can simulate a short between both wires or a short to one of two externally applied fault conditions – such as battery supply or ground - via two fault buses.
