Filter Results By:
Products
Applications
Manufacturers
Depth
how far down in.
- Virginia Panel Corporation
product
Enclosure, G12x, Front Mount, Sloped, 15" Depth
410114003
Enclosure, G12x, Front Mount, Sloped, 15" DepthHousing: Material = .06" Aluminum, Finish = Powder Coat BlackCover(s)/Access Panel(s): Material = .12" Aluminum, Finish = Black Anodize
-
product
Enclosure, 25 Module, Large
410112368
The 25 Module Enclosure, Part # 410 112 368 is made of aluminum, painted black and secured to the ITA by eight socket head cap screws (included). It is equivalent in length to the 50 module enclosure with a depth of 6" and handles on each side.
-
product
Field thermal needle system for thermal resistivity / conductivity measurement
FTN01
Hukseflux Thermal Sensors B.V.
The FTN01 Field Thermal Needle System allows performing fast, on-site measurements of the thermal resistivity or conductivity of soils, in particular around the typical depth of burial of high voltage cables. FTN01 is designed with a focus on robustness and saving time, while still offering sufficient accuracy for typical field measurements. The sensor is a Non-Steady-State Probe (NSSP), TP09, which is mounted at the tip of the Lance LN01. The system is operated using a hand-held Control and Readout Unit CRU01.
-
product
G201A 1-3 Sharp Point Tester
G201A1-3
To determine whether accessible sharp points on child-related products are likely to cause injury. If the accessible sharp point penetrates a specified depth into the small rectangular opening of the tester, the LED is illuminated to indicate that the point is unacceptably sharp.
-
product
Microscopic Probes
M12PP
CAPRES M12PP Microscopic Twelve-Point Probes are specialized versions of the CAPRES Micro Multi-Point Probes. By using a dedicated 12-by-4 multiplexer, a total of 495 different pin-configurations can be obtained, each with different probe pitch. This is utilized in e.g. the CIPTech, where 8 or more combinations are used to obtain a “depth profiling” of the measured structures.
-
product
PCI Express A/D Board
AD12-2000 - Dual 12 bit, 2 GS/s, up to 7GB/s DMA
The AD12-2000 series has two 2000 MS/sec 12-bit ADCs, 8GB of on-board memory and the ability to transfer data directly into the host computer's memory at up to 7 GB/sec. Streaming to the host computer can be performed simultaneously with acquisition to on-board memory, increasing the effective acquisition length by using the host computer's memory. Dual channel boards sample concurrently at the input clock frequency, and can also be software selected to run in single channel mode, at twice the effective memory depth and speed (up to 4 GSPS).
-
product
3/4D Image Visualization and Analysis Software
Imaris
Our latest release, Imaris 8.4, introduces a new and innovative approach to tracing neuron structures in 3D images. Torch™, a patent-pending tool which intuitively highlights structures in close proximity to the cursor while darkening the rest of the image, enables users to efficiently and accurately trace individual neurons within dense and thick samples. Improved depth visibility makes tracing in thick samples easier than ever before, allowing for the selection of a dynamic region of interest for tracing. All of this possible with terabyte-sized datasets.
-
product
Next Generation Subsea Attitude and Heading Reference Systems
TOGS
The new TOGS subsea navigation system is built on core TSS fibre optic gyro (FOG) navigation technology with significant improvements in efficiency and functionality. It is available in three standard heading accuracy variants: 0.1° (TOGS1), 0.3° (TOGS3) and 0.5° (TOGS5), all rated for operational depths to 4,000m or 6,000m. Attitude data is delivered via accurate roll/pitch measurement capabilities of 0.01° (TOGS1) and 0.05° (TOGS3 and TOGS5), and a heave performance of 5cm or 5%.
-
product
Enclosure, G18, Hinged Cover, 3 Cable Clamps, 7" Depth
410112664
Enclosure, G18, Hinged Cover, 3 Cable Clamps, 7" DepthIncludes hinged cover, handles and 3 cable clamps- allow a max. cable bundle of 1.59 sq. inches per clamp. ITA strain relief plates. Housing: Material = .06" Aluminum, Finish = Powder Coat BlackCover(s)/Access Panel(s): Material = .12" Aluminum, Finish = Black Anodize
-
product
Wall Scanner
PeakTech Prüf- und Messtechnik GmbH
The new PeakTech 3433 was specially developed for daily use in the craftsmanship, as it can be used to locate wood, metal or live lines to make sure that no damage is caused through the work of chiseling, slitting or drilling into walls. The inverted LCD display shows the distance to the material which has been found and helps the user to assess the internal condition of the wall to avoid damage to pipes or live circuits. The depth of reception of the sensor is between 20mm (wood) and 120mm (ferrous metal) depending on the material sought. In addition, an LED (green, yellow, red) indicates whether a material has been found or whether there is a live line at the current test point. The simple operation, safe application and high-quality workmanship makes this model an indispensable companion for every craftsman, handyman or installer for maintenance and all work in the building sector.
-
product
Steel Ruler Water Level Meter
SG-80
Wuhan Sangao Electrical Test Installations Limit Co.
This Steel Ruler Water Level Meter is the high accuracy instrument to measure water level. It is common used to measure the water level in wells, boreholes and standpipes. The depth is to 900 meter.
-
product
Surface Analysis
A UHV surface analysis system for thin film depth profilingMeasures the surface composition of the first few nanometers and/or micrometers depth of solid samples.
-
product
Enclosure, G20, Hinged Cover, 4" Depth
410112790
Enclosure, G20, Hinged Cover, 4" DepthHousing: Material = .06" Aluminum, Finish = Powder Coat BlackCover(s)/Access Panel(s): Material = .12" Aluminum, Finish = Black Anodize
-
product
PDS Cutter Dredger Monitoring Software
TELEDYNE PDS for Cutter Dredges is designed to the requirements of the dredge operator to carry out their job more efficiently. The operator has a real time overview of the dredger with the top and side views displaying the vessel outline, ladder, and cutter head along with the surveyed depths, design, and dredged depth.
-
product
Seismometers
3T-120 Pothole
120 s to 50 Hz frequency response (option to 100 Hz), 1500 V/ms-1 (2 x 750 V/ms-1) sensitivity, Covers the complete seismic spectrum with a single transfer function, Measured Self noise below the USGS NLNM from 166 s (0.006 Hz), remaining below the high frequency limit of the NLNM at 10 Hz, High linearity: >111 dB (USGS figures), Dynamic range of 167 dB at 1 Hz (Full octave width across 1 Hz), Cross axis rejection over 65 dB; sensor axes orthogonal to within ±0.05°, Remote, automatic electronic mass locking, unlocking and centring, Operating tilt range of ±5° with adjustable feet for off-horizontal installation bases, Low power consumption: 0.75 W from a 10–36 V supply, Stainless steel enclosure, 100 bar / 10 MPa waterproof connector, IP68 - protection against effects of permanent immersion under pressure to 350 m depth
-
product
Micrometers - Depth
Is used to find the distance between two parallel surfaces i.e. depth of holes, slots, shoulders and projections.
-
product
T3DSO2000HD Series Oscilloscopes
T3DSO2000HD Series
The Teledyne Test Tools T3DSO2000HD Oscilloscopes feature four channel bench models with analog bandwidth options of 100 MHz, 200 MHz and 350 MHz all with 12 bits of vertical resolution. The series offers both DSO and MSO configured models with the MSO units having a 16 channel logic probe as standard. Each model offers a maximum sample rate of up to 2 GSa/s sample rate (interleave mode), and a maximum memory depth of 200 Mpts in interleave mode.
-
product
S6 Slide Mount
For maximum versatility and easy access to instrument-side wiring and cable assemblies, VPC offers a selection of slide kits designed to fit most common test racks. Slides are rated to support 180 lbs (81 kg) to accommodate even the largest fixtures. Measure the rack depth between mounting rails and choose the slide kit that fits the rack. A rack extender kit is available for mounting to racks with recessed rails.
-
product
PDS Ploughing Software
Teledyne PDS Plough supports different ways to monitor your leveling operation. Teledyne RESON provides the software as well as the sensors to accompany the system.Teledyne PDS visualizes the plough in top, profile, and 3D views indicating where leveling has taken place. The position and depth of the plough is logged to a digital terrain model (DTM) which is color-coded for depth. It is possible to display a design depth in the profile views, indicating whether the plough has to be lowered or hoisted.
-
product
Aeroflex AIDE
This programming environment for analog and digital in-circuit test and function test allows a high depth in the realization of inspection tasks. We have many years of extensive experience in dealing with AIDE.
-
product
Next Generation Subsea Inertial Navigation Systems
TOGSINS
The new TOGSINS builds on core TSS fibre optic gyro technology by incorporating inertial navigation (INS) capability. As with TOGS, it is available in three standard heading accuracy variants: 0.1° (TOGSINS1), 0.3° (TOGSINS3) and 0.5° (TOGSINS5), all rated for operational depths to 4,000m or 6,000m giving you a range for all your needs.Inertial position data is produced using an INS algorithm, within the firmware framework of TOGS, whilst attitude data is delivered via accurate roll/pitch measurement of 0.01° (TOGSINS1) and 0.05° (TOGSINS3 and TOGSINS5), and a heave performance of 5cm or 5%.
-
product
Enclosure, S6, 2U Height, 4 Cable Clamps, 12" Depth
410112712
Enclosure, S6, 2U Height, 4 Cable Clamps, 12" Depth Includes hinged cover and 4 cable clamps for discrete wiring that provide secure strain relief. With the cable clamps open- stiffener bar can be removed allowing installation or removal of cables without unplugging patchcords from the assembly. Housing: Material = .06" Aluminum, Finish = Powder Coat BlackCover(s)/Access Panel(s): Material = .12" Aluminum, Finish = Black Anodize
-
product
Downhole Minimus
For deployments exceeding 100 metres in depth, we recommend the Downhole Minimus digitiser. Digitizing the data at source ensures that the origin can be definitively traced and not subject to attenuation during the travel to the surface; so signals are stronger and more reliable.
-
product
102-Channel Portable Logic Analyzer
16863A
102 channels, 350 MHz state, 12.5 GHz timing zoom, 2.5 GHz timing, 2 Mb depth standard15-inch (38.1 cm) color, touch-screen display for viewing and quickly navigating large numbers of signals and buses Built-in removable SSD drive, USB 3.0 ports and LAN for fast data transfer and storage of large amounts of data1.4 GHz trigger sequencer to ensure high-speed events are captured
-
product
Multiparameter Water Quality Probe
Model GEO-AQUpro
Up to 11 sensors (9 + temperature and pH ref) from the following list: Temperature, Optical Dissolved Oxygen, Specific Conductance, Salinity, Total Dissolved Solids (TDS), pH, ORP, Depth, Turbidity, Chlorophyll a, Rhodamine, Blue-Green Algae, CDOM / FDOM, Optical Brighteners, Tryptophan, Fluorescein, Refined oil, Crude oil, Ammonium, Nitrate, Chloride, Sodium, Total Dissolved Gas (TDG), up to 5 User Configurable Parameters (calculated e.g. TSS).
-
product
9050 Slide Mount
The 9050 Slide Configuration provides maximum test system versatility. This configuration allows for easy instrument wiring and chassis access which allows for shorter cable lengths and a flush rack mount to save valuable work space.Ordering has been simplified with packages offered that include the 9050 receiver, receiver mounting plate, flanges and instrument bracket. Slide kits are available in depths designed to fit most common racks. To determine the slide kit needed, measure rack depth between mounting rails. Slides are rated to support 180 lbs (81 kg) to accommodate even the largest fixtures.
-
product
Water Monitoring Modules
Unidata offers a wide range of instruments to suit the measurement of conductivity, evaporation, water depth and temperature. In addition to those water instruments, Unidata also offers Starflow QSD ultrasonic Doppler velocity and depth SDI-12 Instrument.
-
product
2MP Stereo Camera for NVIDIA® Jetson Nano™/AGX Xavier™/TX2
STEEReoCAM™
Houses two OmniVision's 1/2.9" OV2311 Monochrome image sensorHigh-speed 2-lane MIPI CSI-2 interface to connect with the Host ProcessorPlugs in to NVIDIA® Jetson Nano™/AGX Xavier™/TX2 developer kit2MP Global Shutter Sensor10-bit Monochrome output formatHouses 6-axis Inertial Measurement Unit (IMU)Baseline distance of 100mmAccurate depth sensing with a flexible range between 0.95m to 8mS-mount lens holder (M12) with pre-calibrated S-mount lens pairSupport Multiple SteereoCam to a Single board
-
product
Digital output version optical fast DO sensor
RINKO II / II D
Rinko II is a digital output version with a fast-response optical DO sensor. The instrument can be easily integrated on platforms, because it works with communications by RS-232C or RS-485 and an external power (12 to 24V DC).Rinko IID has not only a temperature sensor but also a depth sensor. Their models can monitor DO in real time, if you have a personal computer and an external power.
-
product
PCI-E Server Platform
PCI-E 20 Slot 4U
The brand-new PCI-E server platform features 20 fully-fledged PCIe card slots along with a built-in CPU card based on double Intel® Xeon® CPU. This powerful CPU card and x16 PCI-E (Gen3) available to all 20 slots unleash the unprecedented performance in a very compact 19″ form factor with only 4U height and 20” depth. A big selection of commercial off the shelf (COTS) PCIe cards, such as GPU, Flash storage, FPGA, DSP cards, etc. enables a variety of system configurations. The platform is ideally positioned for high performance computing (HPC), deep learning, artificial intelligence (AI), high-end storage, and other applications.
-
product
Scanning Electron Microscopy (SEM Analysis)
Rocky Mountain Laboratories, Inc.
Scanning Electron Microscopy (SEM Analysis) can produce images of almost any sample at magnifications of 15-300,000X. The SEM has tremendous depth of field allowing for imaging that cannot be accomplished using optical microscopy. Conductive and nonconductive samples can be imaged. When operated in the backscatter (BSE) detection mode, differences in material composition can be observed. Elemental analysis can be performed on any feature observed with an integrated Energy Dispersive Spectroscopy (EDS) detector.
