Reference Transmitters
high quality optical transmitters for test and measurement.
See Also: References, Reference Standards, Reference Antennas, Reference Decoders, Reference Jumpers, Reference Sources, Reference Transformers, Acoustical References, Frequency References, Solar Reference Cells, Fiber Optic
-
product
Hotwire Air Speed Transmitters
HD403TS… Series
Range hotwire transmitters with 0-10 V or 4-20 mA output. Directional or omnidirectional probes.
-
product
Bloomy Simulation Reference System
The Bloomy Simulation Reference System provides a hardware in-the-loop (HIL) test environment for dynamic, closed-loop testing of many aerospace and transportation control systems. The reference system integrates the computing, I/O, and software components needed for standalone use or to form the basis of a more complex test system.
-
product
Differential Pressure Transmitter
616W
Positive, negative and differential pressures can be measured within a full span accuracy of ±0.25 with the Series 616W Differential Pressure Transmitter. Units are enclosed in a polycarbonate case, rated NEMA 4X (IP66) and operate by sensing the pressure of air and compatible gases then sending a standard 4-20 mA output signal.
-
product
Magnetostrictive Level Transmitter
DM330
The Drexelbrook DM330 magnetostrictive level transmitter is a two wire loop powered intrinsically safe sensor with a configurable 4 -20 mA span.This level transmitter uses proven machine tool positioning accuracy combined with a process compatible float to offer a liquid level, and interface measurement system for the process industry.It comes in a patented low clearance design with all of the sensor’s electronics integrated in a 5/8” diameter sensing tube eliminating the electronics enclosure at the top of the sensor. Not only does this result in reduced cost it also offers its user greater options for insertion and mounting.The DM330 is available in two models.The rigid 316SS model offers a choice of a mini-connector or an optional housing including terminal connectors with zero and span adjustments.
-
product
Chilled Mirror Transmitter
DewTrak II
The DewTrak II uses the chilled mirror dew point temperature condensation principle to determine the water vapor concentration in gas mixtures, and a platinum resistance thermometer to accurately measure that temperature. Outputs include 4 to 20mA, 0 to 5 Vdc, or 0-10Vdc and an RS232 serial port as well as electrically isolated relay contacts.
-
product
Transmitter System for Low Signal Power Relay Stations
AM3000 Series
Japan Communication Equipment Co., Ltd.
This system is a minimal low signal power transmitter for the relay of ISDB-T Digital Terrestrial Broadcasting. As the need arises, it's possible to have the compensation function built-in for integrate-type basic equipment.
-
product
4-Band SAT-IF Overlay Direct Modulated Optical Transmitter
HDS-55S ( 950~5500MHz )
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HDS-55S series 1550nm wide band micro-wave internal modulation optical transmitter， RF working 950~5450MHz.It cam It can transmit multi( stacker) 4 way SAT-IF signal in one fiber to realize two polarized 4 way SAT-IF signal in one satellite。or 4 way SAT-IF signal in different satellites to convert all of them into one fiber.。Through FTTH，users use ordinary satellite receiver and STB to receive satellite video carrier the integrate TV programs. It can supply high quality of satellite TV service up to 3000 SDTV or 600 HDTV channel.
-
product
Temperature Transmitter
SenseAir CO2
aSENSE is an advanced transmitter for installation in the climate zone. It measures both CO2 concentration and temperature. The data is transmitted to a BMS system or controller and can be configured with UIP Software. Detected values are transformed into two analogue output signals that can be transmitted to a system master or DDC. aSENSE is available both with and without LCD display for FIXED installation in the climate zone as well as in the ventilation duct.
-
product
AC Reference Generators
SR25
Computer Conversions Corporation
The SR Series are miniature, low cost AC reference generators designed to supply 26 or 115 volt excitation to synchros or resolvers in military and industrial control applications. They accept +/-15V DC and provide up to 5VA of transformer isolated output power. These converters are packaged in PC card mounting modules 2.6”x3.1”x1”H.
-
product
Precision SOT-23 FGA™ Voltage References
X60003
The X60003 FGA™ voltage references is a very high precision analog voltage reference fabricated in Renesas' proprietary Floating Gate Analog technology, which achieves superior levels of performance when compared to conventional band gap, buried zener or XFET™ technologies.
-
product
CO2 Concentration Transmitter
H5424
The regulators are designed for online measurement of temperature (C or F), relative humidity and carbon dioxide concentration of air without aggressive ingredients. Measured temperature and relative humidity are recomputed to following humidity expression: dew point temperature, absolute humidity, specific humidity, mixing ratio and specific enthalpy.
-
product
Attitude Heading Reference System
M&M Modules
PNI’s M&M modules will self adapt and learn its system and its environment automatically to provide accurate quaternions, heading, pitch and roll. All while using 100 times less power than traditional AHRS modules.
-
product
5VA Reference Supply, DC input
PS5410C-16
The PS5410C-16 is a 5VA AC Reference Power Supply, available with many transformer isolated output voltages at different frequencies. Input power is either 12 VDC or 15 VDC. The standard 15 pin "D" connector simplifies interconnection to other equipment.
-
product
Solar Radiation Sensors & Transmitters
A70 Series
The Comptus A70 Series solar radiation sensors with transmitters are available in two models. The A70-A PAR Sensor measures photosynthetically active radiation (PAR) in the 400 to 700 nm range. The A70-I Insolation Sensor measures solar radiation in the 280 to 2800 nm range. The signals from the sensors are scaled by the signal conditioner to provide the desired output.
-
product
1-Watt Transmitter
VM-560FF
The VM-560FF Transmitter has one induction frequency; three direct connect and a fault-find frequency. The LED indicators on the transmitter show the frequency selected, output level, and battery status. An audio indicator beeps to advise the quality of the connection. This one-watt transmitter can transmit the locate signal onto the target line three ways. By direct connection, if direct access to the line is available, by induction by simply putting the transmitter in induction mode and placing it over the target line with the induction arrow in line with it or by clamp mode and using the induction clamp to clamp around the target line.
-
product
Level Transmitter (Immersion)
LS
● Outer diameter Φ 28 stainless steel shell, rugged exterior is easy to install● 3 sealing process, rigorous and reliable sealing● High accuracy, high stability, low cost● Signal isolation amplifier, anti-jamming● PTFE breathable cable
-
product
Custom Transmitter Modules
AMC and TX
Transmit systems are designed for either high-power or broadband operation.
-
product
Motion Reference Units And Wave Sensors
MRU And WS
The Motion Reference Unit (MRU) product line was first released in 2004 when Inertial Labs MEMS-based sensor solutions began to compete in performance with traditional FOG units. Easy integration of the MRU product line for the end user means competitive performance at no extra cost.
-
product
Standard Clamp-On Ultrasonic Transmitter
KATflow 100
The KATflow 100 is a compact clamp-on ultrasonic flow transmitter with a robust and practical design for permanent installation and flow measurement on single pipes.
-
product
Pneumatic Pressure Transmitters
Deltapi N Series
Deltapi N series includes a range of pneumatic transmitters suitable for reliable measurements of pressure, differential pressure, flow or level of liquids, steam and gas. Deltapi N transmitters provides a wide selection of measuring elements to match required working pressure ratings and calibrated spans.
-
product
Intelligent Reference
TM-4D
The Intelligent Reference/TM-4D™ breaks new ground for time and frequency references. For the first time, it is possible to generate and distribute both analog and digital signals to multiple instruments and locations with just one product that fits in a single rack space. The TM-4D is three instruments in one: an Intelligent Reference/TM-4™ precise time and frequency reference, a digital signal distribution amplifier and an analog distribution amplifier. And it eliminates the need for multiple boxes.
-
product
HVAC Pressure Transmitter
DP850/851
The DP850/851 transmitters are designed for low pressure measurement in HVAC applications. The DP850 is available in full scale pressure ranges as low as 0.25 inH2O and the DP851 can be ranged to 0.025 inH2O full scale. Both models are available in 4-20 mA or 0 to +5 Vdc signal output options.
-
product
Miniature Telemetry Transmitters
Advanced Telemetrics International
ATi manufactures digital and digital multiplexing telemetry transmitters in a variety of shapes and sizes to fit any application. Custom shapes for special applications or embedded transmitters can also be created.
-
product
950~2600MHz. SAT-IF Direct Modulated Optical Transmitter
HDS-26S
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HDS-26S (original model: HDBS-3000TX) series satellite L-Band optical transmitter, adopts high linearity DFB laser and direct modulated way. It can transmit 950~2600MHz L-Band analog or digital satellite signal (SAT-IF) receiving by satellite aerial radio high frequency head, to realize total transparency, high quality, long distance transmission through optical fiber. It also can sue satellite L-Band up/down link.
-
product
Hazardous Location Transmitter
X80 Series
The ECD Hazardous Location Transmitters – Model X80 Series provides the same capabilities and general feature set as the general purpose T80 Universal Transmitter. Various configurations are available as single or dual channel for the continuous measurement of pH, ORP, pION, Dissolved Oxygen, Turbidity, Conductivity or Resistivity. The Model X80 transmitter digitally communicates with any ECD Model S88 and/or S80 Intelligent Sensor, automatically configuring the transmitter’s menus and display screens to the measured parameter. The X80 is designed with a durable stainless steel enclosure for explosion proof/exd hazardous applications.
-
product
CW Test Transmitters / Signal Generators
The WTX CW test transmitter family is particularly designed for field applications such as Inbuilding site modeling (model calibration), DAS injection / testing, walk-testing as well as outdoor path model tuning- thanks to its broad range of optional power amplifiers.
-
product
Magnetostrictive Level Transmitters
ABB's K-TEK level products' patented sensor technology allows the LMT series transmitters to be used in the most challenging of industrial level applications such as interface measurement, compressor level and separator level applications. In addition, the LMT Series Level Transmitters are the only magnetostrictive level transmitters in the world to be certified for use in SIL2 and SIL3 systems per IEC61508.
-
product
Automated UV Transmittance / SPF Analyzer
Solar Light’s versatile SPF-290AS UV Transmittance / Sunscreen Protection Factor Analyzer is an integrated turnkey desktop system for quick, efficient, and accurate UV Transmittance analysis of sunscreens, liquids, lotions, creams, sprays, gels, powders, emulsions, textiles, and more!
-
product
Barometric Pressure Transmitter
T2114
Barometric pressure transmitter for outdoor and indoor use.Display reading and pressure output is user selectable in these units: hPa, kPa, mbar, mmHg, inHg, inH2O, PSI, oz/in2.
-
product
SMARC 2.1 Reference Carrier Board with M.2 Extension
I-Pi SMARC Plus
The I-Pi SMARC Plus is small (110mm x 110mm) SMARC reference carrier board based on SGeT SMARC (Smart Mobility ARChitecture) 2.1 hardware specification. Together with the SMARC short size module of your choice and off the shelf add-on cards, you can quickly emulate the functionality of your desired end product for software development and hardware verification.
