Filter Results By:
Products
Applications
Manufacturers
- Pickering Interfaces Inc.
product
PCIe to PXI Remote Control Interface Kit
41-924-001-KIT
The kit is supplied with a PCIe card which can plug into any PC PCIe slot, a PXI module for insertion into Slot 1 of a PXI chassis and 3m lead to connect the two parts together. The interface uses a single lane PCIe connection from the PC to provide a software transparent link from the PC PCIe backplane to the PXI backplane. The supplied 3m shielded lead ensures the system has robust operation and an adequate separation distance between the PC and the PXI chassis.
-
product
cPCI and PMC Compatible Adapter Carrier
cPCIBPMC3U64ET
By customer request Dynamic Engineering has developed two extended temperature versions of the popular cPCIBPMC design. The design effort included switching to a new bridge to meet the temperature and timing requirements. The new bridge brings new features including the ability to operate the PMC side at a higher clock rate than the cPCI side. The new bridge also has built in features for local address spaces, using the PMC clock in monarch mode for the secondary side, and operating in transparent or non-transparent modes
-
product
PXI Signal Insertion Switch Module
PXI Signal Insertion Switch Modules, also known as fault insertion units (FIUs), provide a set of feedthrough channels, which make the switch transparent to the system when closed. You can open or short these channels to one of two fault buses, allowing you to simulate open or interrupted connections as well as shorts between pins, shorts to battery voltages, and shorts to ground on a per-channel basis. When controlled with the LabVIEW Real-Time Module, the PXI Signal Insertion Switch Module can validate the integrity of control systems including engine control units (ECUs) and full authority digital engine controls (FADECs). You can also use the FIU models for hardware-in-the-loop (HIL) applications and electronic reliability tests.
-
product
Scanning Probe Microscopes
SpectraView 2500
* Ultra-low noise SPM* Colocalized nanochemical analysis by IR, THz, Raman, AFM* Cantilever probes are completely transparent* Versatile configurations: Kelvin Probe chemical potential, electrical, thermal and photon force
-
product
PMC-to-PCI Express Adapter
4749
Our PMC-to-PCI Express Adapter 1X (64-Bit) (4749) permits the use of a single-wide PMC module in a 1X PCIe slot. The product features a PEX8114 bridge running in transparent mode.
-
product
Ultrasonic Sensors
Leuze electronic GmbH + Co. KG
Ultrasonic sensors are used whenever optical systems reach their limits. Hence, partially and fully transparent or extremely dark objects can be detected just as easily as objects with reflecting surfaces or objects in dusty, vaporous or humid environments.
-
product
Thickness Gauges
Bristol Instruments'' optical thickness gauges are a simple and non-destructive way to precisely measure thickness of a variety of transparent and semi-transparent materials. Thickness information is critical in the development and production of materials such as contact and intraocular lenses, and medical products including balloon catheters, stents, bags, and tubing. Bristol combines high accuracy with straightforward operation and rugged design to make these instruments ideal for both laboratory and manufacturing environments.
-
product
Multi-Functional Optical Profiling system
7505-01
Chroma 7505-01 is the newest multi-function optical inspection system that equips with the capability of measuring 1D, 2D and 3D at the same time. Penetrating reflection measurement is used for 1D film thickness measurement to measure the non-destructive film thickness on transparent and translucent material.
-
product
Professional Geological Compass
COCLA
F. W. Breithaupt & Sohn GmbH & Co.KG
*Measurement and reading of azimuth of dip and angle of dip in one single operation (according to Clar method)*Declination (± 30°) and inclination adjustable*Automatic arresting of needle when not in use*Eddy current damping allows reading after approx. 3 sec.*Transparent circle with diameter 50mm with interval of graduation 1°*Dip measurement range 270° graduated in 5°Reading by estimation 1°*Deep etched tracing edge graduated (60mm)*Circular spirit level (observable also from underneath)
-
product
Sensors
Chromatic Focus Probe
Measurement of highly reflective, absorbent and transparent materialsMeasuring results are independent of the surface propertiesEspecially suitable for fast and precise measurements on reflective surfaces, lenses, prisms and other optical devicesFlexible probe configurations for highly customized applications
-
product
Intelligent Stirrer
Model 901
Intelligent chip design. Ability to set and store the stirring rate. Ability to switch between two kinds of stirring speed after pressing “PRM” button.Options of AC and DC. Applied in the field or in the incubator. MoreIntelligent chip design. Ability to set and store the stirring rate. Ability to switch between two kinds of stirring speed after pressing “PRM” button.Range: 0 to 2300 R/M (no load)Nice appearance, transparent coping designused with AC or DC, and a battery low voltage alarmused in lab, in incubator and brought outdoorsEquipped with strut and electrode holder, it can be used as agitating arc-spark standIP54 dustproof and splash proof.
-
product
Beverage Analysis
Analyze multiple quality control parameters of your beverages in parallel, within 3 to 5 minutes only. See all parameters on a bright, easily customized 10.4’’ touchscreen display. Anton Paar’s modular beverage analysis solutions are quickly adapted to your needs in a Plug and Play fashion. In any case, the sample filling and measurement process is completely transparent and traceable.
-
product
Ambient Light Sensor
VEML7700 (Qwiic)
Looking for a Qwiic sensor that can measure the ambient light level directly in lux? This is it! The VEML7700 is a high accuracy, 16-bit resolution, digital ambient light sensor in a miniature transparent 6.8 mm x 3.0 mm x 2.5 mm package.
-
product
SUC-C Series Microwave Upconverter
SUC-C
SUC-C Series Microwave Upconverter is a broadband frequency converter that is dedicated for satellite communication. It has a high performance, high reliability and an octave covered by RF signal. Its frequency step is precise and accurate to 1Hz with a variety of IF and signal bandwidth choices. SUC-C series is equipped with functions like self-testing and combination alarm which is suitable for long-time uninterrupted use, guaranteed safety and reliability.SUC-C series microwave upconverter is mainly designed for satellite communication system, signal monitoring system, and electronic countermeasure system with an excellent phase noise, clutter suppression, and in-band flatness data. It is able to provide a transparent RF transmission channel to all videos or data communications. All programming commands can be set through a local panel or through network remotely. SUC-C series microwave upconverter has a standard 2U size.Applications: T&M Systems / Satellite Communications / MIMO
-
product
Versatile AFM Optical Coupling
TRIOS
The TRIOS platform is an advanced research instrument that provides the entry path for researchers in materials science, biology, spectroscopy and photonics. TRIOS is the most versatile optical coupling platform providing three ports for optical spectroscopy measurements with top-down, side (oblique) and inverted accesses to the AFM tip and sample.If you work with opaque and/or transparent samples, either in air or in liquid looking at nanoscale structures and near-field optical properties investigation, the TRIOS platform is the right solution for you. It perfectly combines upright optical, inverted optical, and atomic force microscopies, and unleash all the power of both techniques providing instrument adjustment and measurement automation, high resolution and integration flexibility. Such performance is only available from HORIBA.
-
product
Benchtop Sphere (d/8°) Geometry Spectrophotometers
Hunter Associates Laboratory, Inc.
Diffuse d/8° benchtop sphere spectrophotometers are recommended for transmittance color and haze measurements of transparent liquid and solid samples, and color measurements of opaque samples where it is desired to negate the effects of sample gloss and texture, as is necessary in the color formulation process when determining the effect of pigment variations irrespective of surface characteristics.
-
product
Building Monitoring
Crackmeter
The system consists of two plates that overlap for part of their length. One plate is calibrated in millimeters and the overlapping plate is transparent and marked with a hairline cursor. As the crack width opens or closes, one plate moves relative to the other. The relationship of the cursor to the scale represents the amount of movement occurring. These gauges are monitored over time, whilst being kept as far away from human disturbance as possible, to develop an understanding in the width and direction of movement of the crack.
-
product
PXI-8368, MXI-Express Interface with Connector for Fiber Cable, PXI Remote Control Module
783934-01
MXI-Express Interface with Connector for Fiber Cable, PXI Remote Control Module—The PXI‑8368 allows you to control PXI and CompactPCI systems from your PC using a fully transparent MXI‑Express link. It is installed in a PXI chassis and uses a PCI Express‑to‑PCI bridge to interface with an installed PCI‑8366 through a copper, x1 MXI‑Express cable. The fiber-optic cabling of the PXI‑8368 provides electrical isolation between the PC and PXI chassis, as well as cabling up to 200 m per link.
-
product
Sapphire polariscope optic modulator
PKS-250M
The device is designed for determining double refraction in flat blanks and products of transparent and weakly tinted materials, and is used for quantitative assessment of double refraction value by Senarmon method with an error of not greater than 10 nm, for assessment of double refraction distribution in an object by interference tinting, for examining distribution of double refraction in an object with circularly polarized light.
-
product
TEM Antenna
TEM antenna is a partial discharge sensor designed to receive electromagnetic (EM) emissions from a PD occurring in the monitored asset (like MV switchgears or LV and MV induction motors fed by power electronic impulses). It is a broadband antenna with a flat response which makes TEM suitable in a number of different applications. It has been optimized to operate in a frequency range typical for PD activity and it was designed to provide maximum sensitivity and high gain. Its compact and robust design (passive sensor) makes TEM the optimal sensor for direct installation on medium voltage Switchgears and motors. It can be virtually applied in any electrical equipment provided that it has apertures or EM transparent surfaces.
-
product
Shielding Solutions
The highly transparent EMC shielding material Aaronia-Shield® and the high-tech EMC shielding fleece Aaronia X-Dream®, for example, offer very high EMC protection and are especially well equipped for all future high-frequency radiation sources in the high GHz range, which you can easily verify with our EMC Handheld Spectrum Analyzer. For magnetic field shielding, our MagnoShield® series offers unparalleled protection against alternating magnetic fields, such as cables, power distributors, high-voltage lines or transformers and generators.
-
product
Metallic Pendulum Impact Testing Machine
JB-S Series
Jinan Testing Equipment IE Corporation
JB-S series superior metallic pendulum impact testing system is strictly designed according to international standards ISO148, ASTM E23 and EN10045. The pendulum impact testing system is mainly used to determine the anti-impact capability of metal materials under dynamic load and is capable of doing a large number of of impact tests continuously. Adopting the important intelligent programmable logic controller (PLC) system, the pendulum impact testing system can realize the test process control and test data collection based on computer software program or digital display touch screen controller. The test data can be used for further data analysis, storage and printing. An aluminum shield with transparent tempered glass covers the load frame for safe operation. The impact testing machine of metallic pendulum is the essential quality control equipment for metal material manufacturers and QC departments, as well as the necessary instrument of research institutes for new material research.
-
product
Window Thermometer
P0260
The Sol-Mate Window Thermometer® is solar powered, displays temperature, minimum and maximum values, and even shows temperature trends. Its sleek European design features a transparent housing that is held directly onto your window with a strong suction cup.
-
product
Ultrasonic Distance Sensors
Leuze electronic GmbH + Co. KG
Ultrasonic distance sensors can reliably detect partially or fully transparent objects and perform precise distance measurements. In addition, measurements can be performed in dusty, hazy or humid environments. Versions are available either with plastic or metal housing.
-
product
Refractometers
PCE Instruments carries a number of refractometer models including portable or handheld refractometer, digital refractometer and Abbe refractometer products used in food processing, canning, beekeeping, brewing, winemaking, distilling, pharmaceutical, manufacturing, machining, automotive, oil, petrochemical and water quality industries to measure the percent (%) Brix, salt content (salinity), water content, sugar content, Baumé (°Bé), Oechsle (°Oe), alcohol content or specific gravity (sg) of transparent or semitransparent fluids, liquids, formulas, suspensions, mixtures, dispersions, emulsions, concentrations, pastes and substances such as salt water or seawater, brines, fruits, juices, soft drinks, energy drinks, wines, liquors, condensed milk, jams, jellies, honey, industrial lubricants, antifreeze, ethanol, battery acids, propylene glycol, ethylene glycol, electrolyte solutions, paints, lacquers and chemicals.
-
product
UltraScan VIS Spectrophotometer
Hunter Associates Laboratory, Inc.
The UltraScan VIS easily measures both reflected and transmitted color as well as transmission haze and meets CIE, ASTM and USP guidelines for accurate color measurement. UltraScan VIS uses diffuse/8° geometry with automated specular component inclusion/exclusion. For transmission measurement, the use of a robust CIE-conforming sphere instrument (TTRAN Total Transmission mode) effectively negates the effects of minor scattering typically found in transparent samples.
-
product
4X14 Gb/s QSFP/QSFP+ Evaluation Board
EV-QSFP-174
The EV‐QSFP‐174 QSFP/QSFP+ Host Test Board comes complete with Windows based software (Windows XP & above) to enable intuitive memory map programming and testing, controlled via a mini B USB port. It is designed to simulate an ideal environment for QSFP/QSFP+ transceiver module testing, characterization and manufacturing test. Its high speed properties make the host board as electrically transparent as possible, allowing for a more accurate assessment of the module’s performance.
-
product
500 MHz, 1.0 pF Active Differential Probe
ZD500
With the ProBus interface, the ZD500, 1000, and 1500 becomes an integral part of the oscilloscope. All probe gain and offset controls are transparent to the user, making it easier to probe the circuit without concern for which gain setting to choose. When used with a LeCroy digital oscilloscope, no external power supply is required.
-
product
Fibre Channel Test & Simulation Interface for PCI Express
PCIe-FC4
Avionics Interface Technologies
Half-size four lane PCIe board - Supports Point-to-Point, Switched Fabric, and Arbitrated Loop topologies - Two independent Fibre Channel ports - Two SFP sockets accept fiber or copper transceivers - Each port supports 1, 2, and 4 Gbps speedsComprehensive decoding of FC-1, FC-2, and Upper Layer Protocol (ULP) frames - Full Error Injection and Detection - IRIG-B Time Code Encoder/Decoder for Data Correlation - In-line Port Configuration for Transparent Analyzer - Supports multiple ULPs including FC-AE-ASM, FC-AE-RDMA, FC-AE-1553, and FC-AV - Compatible with AIT’s fcXplorer GUI Bus Analyzer Software
-
product
2-in-1 High-Voltage Test Hood
LX-HVE900EC
The test cells are made of stable, highly insulating plastic and are closed by a swiveling, transparent cover. The built-in safety switch is used to lock the hood and release the high-voltage sources. This ensures that no high voltage is active when the door is open. There is a generously dimensioned wiring space in the floor of the test cage. An interchangeable adapter plate in the test cell - optionally with an interchangeable interface or an interchangeable adapter cassette - allows quick adaptation to different types of test items. Prepared openings enable connectors and other common interfaces or cable bushings to be easily attached. The hood is opened and closed almost effortlessly thanks to precisely coordinated gas springs.
