CompactPCI Express
electro-mechano interoperability with PXI Express. Also known as: cPCIe
See Also: Compact PCI, cPCI, PXI Express, PXIe, PXIE
-
Product
12- Port PCI Express
PEX 8632
-
The ExpressLane™ PEX 8632 device offers 32 PCI Express Gen 2 (5.0 GT/s) lanes, capable of configuring up to 12 flexible ports. The switch conforms to the PCI Express Base Specification, rev 2.0. The 32-lane switch enables users to add scalable, high bandwidth, non-blocking interconnection to a wide variety of applications including servers, communications, storage, blade servers, and embedded systems.
-
Product
6U CompactPCI Dual 64-bit PMC Slots Carrier Board
cPCI-8602
Carrier Board
- Supports two single-size 32,64-bit/33,66 MHz PMC sites in 4HP width- PICMG® 2.0 32,64-bit/33,66 MHz cPCI bus- PICMG® 2.1 Hot Swap Specification Compliant- 3.3V or 5V V(I/O) for cPCI bus and PMC sites- PLX® PCI-to PCI bridge PCI6154 for PCI bus- Power and HotSwap LED incidators on front panel
-
Product
Mini PCI Express
MPCIE-A429
Interface Card
Alta Data Technologies’ MPCIE-A429 Mini PCI Express F1 interface module offers a variety of ARINC-429/575/717 channel configurations with software selectable RX/TX channels, baud rates, bit encoding and word configurations (Start/Sync/Stop length, Parity, bits/word, MSB/LSB). Encode or decode almost any ARINC-429 transceiver compatible signal.
-
Product
Stepper Motor Controller for CompactPCI
CPCI322
-
The CPCI322 is a 3U CompactPCI card. The CPCI322 Intelligent Stepper Motor Controller is designed to drive external amplifiers. This is an ideal solution for all applications where stepper motors must be controlled with a maximum of flexibility and a minimum of overhead.
-
-
Product
PCI Express Cable Extender
SKU-016-XX
-
The PCI Express Cable Extender was designed to support the development and debugging of PCI Express boards. The PCI Express Cable Extender allows easy access from both sides of the PCI Express board that are plugged into the Extender. It has overcurrent protection and provides access to the PCI Express bus JTAG signals. By enabling access to the PCI Express bus JTAG signals, the PCI Express Cable Extender becomes a universal device that helps support the programming/loading of FPGA/CPLD during debugging and the verification PCI Express boards.
-
Product
Low Profile PCI Express 2-Port
7202ec
-
The 7202ec low-profile PCI Express serial interface provides two RS-232 serial ports. All modem control signals are implemented for maximum compatibility with a wide range of serial peripherals. Each serial port features an ultra high-speed UART, flexible clock prescalar, and large 256-byte Tx/Rx FIFOs allowing the adapter to support the widest range of standard and non-standard baud rates exceeding 1 Mbps. These features make the 7202ec ideal for data intensive applications that require reliable, ultra-fast throughput rates.
-
Product
PCI Express Cameras with high speed and resolution
CB120MG-CM
-
4K, compact, high speed camera for: Flat panel inspection (FPD), printed circuit board (PCB) examination, solar panel analysis, persistent stadium and border security, wide area surveillance, cinematography, sports and entertainment, 360 panorama, UAV and Autonomous, Unmanned vehicles, aerial or city mapping.
-
Product
COM Express Type 7 Starter Kit
COMe Type 7 Ice Lake-D STKit
-
The Type 7 Starter Kit Plus consists of a COM Express Type 7 module with ATX size Type 7 reference carrier board that offers one PCI Express x16 slot with proprietary pinout for 10GbE adapter card that convert 10GBase-KR to 10GbE Optical Fiber or 10GbE Copper signal, one PCI Express x16 slot, two PCI Express x8 slots, Serial ATA, USB3.0/2.0, Gigabit LAN and Super I/O. in addition, a IPMI BMC (miniBMC) located on carrier board connect to COM Express Type7 module by NC-SI interface to support some of out-of-band management features. All necessary cables are included.
-
Product
PXI Express Interface
EMX-2500
Interface
The EMX-2500 is the industry’s first gigabit Ethernet LXI based PXI Express interface. This combines Ethernet's widespread usage and robust architecture with instrumentation-specific functionality, such as wired trigger bus and IEEE-1588-2008 synchronization, and extends it for use in PXI Express mainframes, making it an ideal solution for data acquisition applications.
-
Product
5 Port PCI Express
PEX 8505
-
The ExpressLane™ PEX 8505 5-lane, 5-port switch product offers PCI Express switching capability conforming to the PCI Express Specification r1.1. This device with an equal number of lanes and ports can be used in a wide variety of applications including control planes in the communications and networking markets, embedded systems, notebook and docking stations, set-top boxes, digital video recorders and multi-function printers.
-
Product
PCI Express Card Slot Interposer
PCIE850
-
The PCIE850 provides a complete test and debug solution for PCI Express Bus. Interposers and probes connect to the PCIE850 providing access to PCI Card, AMX, XMC and VPX systems.
-
Product
CompactPCI PICMG 2.16 Backplanes
-
Comtel Electronics offers a large variety of CompactPCI 2.16 Backplanes, 8 – 14 slots 64 bit 33Mhz,Fully compliancy with PICMG 2.0 Rev 3.0 Specs & 2.16 Spec. Hot Swap compliant per PICMG 2.1 R2.0 Spec.
-
Product
COM Express
-
COM Express defines standardized footprints and pin-outs for Computer-on-Modules. With the Revision 2.0, PICMG added the compact footprint (95x95mm) to the basic footprint (125x95mm) and extended the pin-outs being future-proof. New Digital Display Interfaces (DDI) and super-fast USB 3.0 are available. The new Pin-out Type 10 in COM Express Revision 2.0 supports perfectly modules in the COM Express mini footprint (84x55 mm).
-
Product
XMC-to-PCI Express Adapter
7769
-
Our XMC-to-PCI Express Adapter 1X w/ VITA 61 (XMC 2.0) Style Connectors (7769) permits the use of a single-wide XMC module in a 1X PCIe slot. PCI express lanes on the P15 XMC connector are routed to the male PCI express edge finger connector.
-
Product
3U CompactPCI Multi-Function I/O Board
CPCI-AD32
Multifunction I/O
The CPCI-AD32 is a 3U CompactPCI multi-function I/O board. The CPCI-AD32 offers 32 channels of 16 bit A/D, two 16 bit D/A, 16 digital I/O, counter / timers.There is a local 60 Mhz TMS320C31 DSP processor to supervise all the I/O activity. The DSP can be programmed by the end user to execute application specific code. The CPCI-AD32 is ideally suited for factory automation, automatic test equipment, test & measurement, and control systems.
-
Product
Flexible Mini PCI Express to MiniPCI Adapter
SKU-066-0X
-
Flexible MiniPCI Express to MiniPCI Bus Adapter (Adapter) was designed to convert motherboard MiniPCI Express bus into a standard MiniPCI bus. It allows connection of a standard 124-pin MiniPCI add-in board to a motherboard’s MiniPCI Express connector via full- or half-size MiniPCI Express host board.Adapter includes MiniPCI Adapter board, MiniPCI Express host board and flat PCI Express Cable.
-
Product
12 Port PCI Express
PEX 8615
-
The ExpressLane™ PEX 8615 offers 12 PCI Express Gen 2 (5.0 GT/s) lanes, capable of configuring up to 12 flexible ports and fully conforms to the PCI Express Base Specification, rev 2.0. PEX 8615 architecture supports a high-performance DMA engine with four DMA channels and internal buffer space for internal descriptor support. Up to 256 descriptors are supported internally or alternatively descriptors can also exist in host memory.
-
Product
Full 4-Axis Motion Control Universal PCI Express Card
PCIE-1245
-
Encoder input: 5 MHz for CW/CCW,P/D,AB mode; Pulse output: up to 5 MHzSupports memory buffer (10 K points) for trajectory planningSupports point-to-point, line and E-Gear; Supports hardware emergency inputCircular and helical interpolation (PCIE-1245 only)Position latch up to 10KHz and memory buffer 1K points (PCIE-1245 only)Position compare triggering up to 100 KHz, and memory buffer is up to 100 K points (PCIE-1245 only)1D&2D plane position compensation (PCIE-1245 only)Gantry mode by semi-closed loop pulse train control (PCIE-1245 only)Dynamic PWM output for velocity following (PCIE-1245 only)
-
Product
PCI Express X4, 4-Port USB 3.0 Expansion Card
PCE-USB
Machine Vision Expansion Module
Four USB 3.0 host controllers, Support 1500mA Max. Current per Port. Supports four or eight USB 3.0 ports, 3 Ports with Locking connector compliant with USB3 Vision V1.0 Standard-A. Compliant with USB 3.0 Specification and Intel® xHCI Specification, Revision 1.0, PCI Express x4 interface.
-
Product
PCI Express Multi-Function Boards
PCIe-8620
-
PCI Express, 200 kS/s High-speed, 16-bit 8/16-channel Simultaneously Sampled Analog Input Board with 4/12-channel Isolated DIO
-
Product
PCI Express
PCIe
-
PCI Express (PCIe) has become the leading interconnect technology to succeed the Peripheral Connect Interface (PCI) architecture. The PCI Express(PCIe) architecture retains the PCI usage model and software interfaces for investment protection and smooth development migration. The technology is aimed at multiple market segments in the computing and communication industries, and supports chip-to-chip, board-to-board and adapter solutions. PCI Express 5.0 currently runs at 16GT/s or 32Gbps per lane in each direction, providing a total bandwidth of 128GBps in a 16-lane configuration which is the largest size in use.
-
Product
Squid Carrier Board™ Family PCI Express Carrier Board for 8 MiniPCI Express Modules
SKU-085-01
-
Squid PCI Express Carrier board for MiniPCIe modules is the first product in the Squid PCI Express Carrier Board™ family. PCI Express Carrier board was designed to expand modern motherboards that have PCI Express interface. It allows connection of up to 8 MiniPCI Express half or full-size MiniPCI Express modules to the one motherboard’s PCI Express slot.
-
Product
24-Lane, 10-Port PCI Express
PEX 8725
-
The ExpressLane™ PEX 8725 is a 24-lane, 10-port, PCIe Gen 3 switch device developed on 40nm technology. PEX 8725 offers Multi-Host PCI Express switching capability that enables users to connect multiple hosts to their respective endpoints via scalable, high-bandwidth, non-blocking interconnection to a wide variety of applications including servers, storage, communications, and graphics platforms.
-
Product
ARINC-429 Controller for CompactPCI
CPCI302
-
The CPCI302 provides four ARINC-429 compatible channels (2x receive and 2x transmit) at any rate between 12.5 and 100kbps. Because the CPCI302 is built upon a flexible platform, the user functions can be implemented almost without restriction, making this product flexible and user-friendly.
-
Product
4-CH 16-Bit 80 MS/s PCI Express Digitizer
PCIe-9834
Digitizer
ADLINK's new PCIe-9834 high-speed PCI Express digitizer, featuring four simultaneously sampled 80 MS/s input channels with 16-bit resolution, 40 MHz bandwidth, and up to 1 GB DDR3 onboard memory. Each of the four input channels supports up to 80MS/s sampling, with 16-bit resolution A/D converter. This allows simultaneous recording of signals on all channels with no interchannel phase delay. The extremely large onboard memory enables long recording times even at the highest sampling rates. Each connection pair (lane) can achieve burst connection speeds of 250MB/s. The PCIe-9834, based on x4 lane slot PCI Express technology, provides a clear advantage in that direct connection of each slot allows full transfer bandwidth for each individual card.
-
Product
4U 5-Slot CompactPCI® Chassis with 400 W Power Supply
cPCIS-6400X Series
Chassis
The cPCIS-6400U/6400X Series subsystems are designed for 6U cPCI boards with 80mm RTMs. The chassis is 4U in height and standard 19" rack mount width. The cPCIS-6400U provides 2+1 hot swappable 500W+250W redundant power supplies with universal AC input, while the cPCIS-6400X has a built-in 400W AC-input ATX power supply with cooling fan. Both series have PICMG 2.1 Hot Swap compliant 32/64-bit 5-slot CompactPCI backplanes and a PICMG 2.5 H.110 CT Bus.
-
Product
14-Slot PICMG 2.16 6U CompactPCI Blade Server Backplane
cBP-6614A
Backplane
- PICMG:2.0 R3.0, 2.1 R2.0, 2.9 R1.0, 2.11 R1.0, 2.16 R1.0- Dimension:Dimension 420.6 x 262.05 (mm, WxH)- 2.16 Node Slot:12- 2.16 Fabric Slot:2- cPCI Bus:None
-
Product
12-Lane, 5-Port PCI Express
PEX 8714
-
The ExpressLane™ PEX8714 is a 12-lane, 5-port, PCIe Gen3 switch device developed on 40nm technology. PEX8714 offers PCI Express switching capability that enables users to connect a host to the endpoints via scalable, high-bandwidth, non-blocking interconnection to a wide variety of applications including servers, storage, communications, and graphics platforms.
-
Product
4 Port PCI Express
PEX 8604
-
The ExpressLane™ PEX 8604 device offers 4 PCI Express Gen 2 (5.0 GT/s) lanes, which supports up to four ports. The switch conforms to the PCI Express Base Specification, rev 2.0. The PEX8604 is the industry's smallest 4-lane Gen 2 device and it enables users with the ability to connect multiple PCI Express endpoints which are used in a variety of consumer and embedded applications including Multi-Function Printers, wireless ethernet modules, IO expansion modules, Express Card applications as well as other low power applications.
