PD Test
partial discharge testing.
See Also: Partial Discharge, Partial Discharge Detection, Partial Discharge Monitors, PD, Partial Discharge Test
-
Product
PD Test Systems
-
1. Number of channels: 2/4 electric signal interfaces & 1 EXT interface 2. Sampling frequency: maximum 200MGa/s 3. Sampling precision: 12bit 4. Range: 0.1mV~20V 5. Range switch: 1mV, 2mV, 5mV, 10mV, 20mV, 50mV, 100mV, 200mV, 500mV, 1V, 2V, 5V 6. Frequency band range: 1Hz-60MHz 7. Range non-linear error: 5% 8. Range of capacitance for test object: 6pF~250µF 9. Power source mode: internal lithium cell / AC 220V 10. Display: 6.5 inches TFT LCD 11. Resolution: 640×480 12. PV: 4GB 13. Hard disk: 32G stiff disk used for storing the test data
-
Product
PD Measuring System
TEM
-
Partial discharge test system for laboratory or on-site measurement according to VDE 0434, IEC 60270 and EN50178 consisting of:*Partial discharge meter TMG*High-voltage coupling capacitors for decoupling of the PD pulses*Partial discharge calibrator TPK for determining the correction factor in the PD test circuit
-
Product
High Frequency Current Transformer
HFCT Ø 140mm
-
Techimp Clamp High Frequency Current Transformer model 140 is an inductive sensor for partial discharge measurements. It is suitable for online /off line PD tests on : large diameter cables ; grounding rod bar ; etc. A TNC termination is available to connect the Clamp HFCT 140 to the TechImp PD analyzer : PDCheck , PDBase etc. The arrow indicates the requested input current (Iin) direction to get coherent output voltage (Vout) polarity respect to ground. When the sensor is installed with the arrow directed to ground, the detected voltage signal (Vout) has the same phase of the input current (Iin).
-
Product
PoE PD Test Solutions
-
Explore PoE PD Test solutions from Sifos Technology. What type of testing does your Power-Over-Ethernet Powered Device need?
-
Product
Cable Partial Discharge (PD) Spot Testing And Locating
PrecisePD
-
PrecisePD is an on-line PD Spot Testing and PD location system for Cables and Switchgear with advanced signal processing, used for the detection of PD in high noise environments.
-
Product
PD Conformance Test Suite for 802.3at & 802.3bt
-
Sifos Technologies offers the ultimate simplicity in testing a PD’s conformance to IEEE 802.3 Standards with Pass/ Fail reporting in the PD Conformance Test Suite available for purchase with the PDA-600 Family of Instruments.
-
Product
Partial Discharge Calibrator
TPK-H
-
The high voltage-resistant Partial Discharge calibrator is used to determine the correction factor in the PD test circui.
-
Product
Superior Handheld Partial Discharge Detector
PDStar
-
Power Monitoring and Diagnostic Technology Ltd.
PMDT is proud to present one of our latest innovations, the PDStar. It integrates On-Line Partial Discharge (OLPD) testing and Infrared testing for MV and HV equipment, which combines UHF, AE, Ultrasonic, HFCT, TEV, and Infrared testing technologies. It is applicable for online PD testing, as well as abnormal heating and defect detection on all types of substation equipment. PD amplitude, PRPD, PRPS, and infrared spectrums provide critical data for determining the operational condition of electric power equipment. It connects to the PMDTCloud via Wi-Fi/3G/4G to upload test data, download test tasks, and receive diagnostic results in real time. Another uniquely advanced feature of the PDStar is that it integrates with a 100 MSPS (Mega-Samples per Second) HFCT signal processor, which greatly improves the performance for power cable OLPD testing.
-
Product
ITSM Synchro
-
The Impulsive Test Synchronization Module (ITSM) is a device aimed at generating a digital synchronization signal, to use the PDBaseII system for impulsive voltage PD test. The digital synchronization signal generated by the ITSM, is synchronized with the voltage impulse of the impulsive source (voltage generator). The ITSM must be connected between the DIN channel of PDBaseII and the output of the synchronization sensor (e.g. capacitive coupler). The ITSM provides also a low voltage signal reproducing the impulsive voltage source.
-
Product
Inductive Sensor
HFCT Ø 30-39-50mm
-
Techimp HFCT is an inductive sensor for partial discharge measurements. It is suitable for on/off line PD tests on many electrical systems (cables, transformers, rotating machine, etc..). It has to be applied to the ground connection of the system to be tested.
-
Product
AC Hipots for Factory and Field Testing
HPA Series
-
HPA Series test sets perform AC withstand and PD testing (most models) on higher capacitance loads, offering up to 40 kVA and 300 kV AC
-
Product
USB PD Test System
6050
-
Single Output USB PD USB PD basic version：the single-group test systemarchitecture is as shown in the table, 5302A AC Source, 3302F + 3310F series and9922-R Quick Charge Controller.
-
Product
PD Free Test Transformer
-
Wuhan Fanke Transformer Manufacture Co., LTD
PD Free Test Transformer
-
Product
Powered Device Analyzer for 802.3at
PDA-602B
-
Emulate all Type-1 and Type-2 PSE’s, powering 2-pairs up to 41W at all PD input voltages. Optionally supports 802.3at PD Conformance Test Suite and LLDP emulations.
-
Product
Universal Partial Discharge Measurement and Analysis System
MPD 800
-
Our MPD 800 universal partial discharge (PD) measurement and analysis system represents the next generation of our widely-used and innovative MPD PD testing technology. Enhanced and newly-added hardware and software features ensure highly-sensitive multi-channel PD measurements for reliable, industry-standard PD testing on a variety of electrical equipment and components.
-
Product
Capacitive Divider
-
It can be chosen as PD sensor for Techimp PDCheck, PDScope or PDBaseII systems. It is suitable for on line or off line PD tests onrotating machines, for both spot measurements and monitoring applications. A BNC termination is available to connect the coupler through a coaxial cable.
-
Product
Interactive Benchtop Test
test
Strict time-to-market deadlines make it vital to efficiently debug and validate product designs. Virtual instrumentation provides a unified interface that gives engineers an advantage over traditional box instruments.
-
Product
Test Management Software
ActivATE™
test
Easily create and run robust test programs in semiconductor automated test systems with ActivATE™ test management software. Designed by test engineers for test engineers, ActivATE™ tames automated test complexities with elegant simplicity.
-
Product
NI Automated Test Software Suite
test
The NI Automated Test Software Suite features all three NI IDEs and NI's most popular application software and add-ons specifically for building your automated test system with confidence. This package offers the power of LabVIEW, LabWindows/CVI, and Measurement Studio combined with the TestStand ready-to-run, test executive and the Switch Executive intelligent switch management application
-
Product
Automated Aerospace and Defense Test
test
Obsolescence management, evolving RF requirements, and design for test (DFT) challenges every test organization in the aerospace and defense industry. Organizations are transitioning from rack-and-stack box instruments and closed-architecture automated test equipment (ATE) systems to smarter test systems built on a modular platform that scales to meet current and future needs.
-
Product
Universal Function Test System for Industrial Electronics
Test System
General functional test system based on LXI instrumentation for high mix / low to medium volume manufacturing. DUTs are tested which are mainly used as communication and measurement modules in power plant technology, grid management and electrical drives.The system has a Virginia Panel adapter interface to which various desk adapters can be docked, including automated contacting of the DUTs. A camera for the verification of light emitting diodes on the test object is integrated in the adapter interface.
-
Product
Conformance Test System
TS-RRM
Test System
The R&S®TS-RRM 5G and LTE test system is a test solution for running 5G NR and LTE inter-RAT RRM test cases for certification of wireless devices.It is a fully automated conformance test system for running validated RRM conformance test cases. In addition to the RRM test cases required by GCF/PTCRB, the R&S®TS-RRM also supports carrier acceptance specific RRM tests.
-
Product
Test Handler
M6242
Test Handler
Optimal Test Handler for Mass-Production DRAM, with Double the Throughput.
-
Product
High Speed Test Bench
AT444
Test Platform
AC motor with mechanical multiplying gearbox test benches allow precise programming of all drive parameters required for accurate rotating devices test.The use of special high-speed bearings, mechanical components and parts wear resistant leads to a large life. The supply includes the electronic drive and control as well as the entire oil cooling unit.
-
Product
LTE RRM Test System
T4010S
Test System
The T4020S LTE RRM tester is the Keysight platform for LTE RRM conformance testing of LTE UEs. T4020S belongs to the Keysight LTE product family and, as the other LTE T4000S test platforms, is based on the T2010A LTE Wireless Communications Test Set.
-
Product
At-Speed Non-Intrusive Functional Testing
ScanExpress JET
Functional Test
Functional circuit board testing presents many challenges that are often costly and time consuming. Most functional tests need to be customized for each design, limiting reusability. This results in software engineers vying for time between development code and test code. Even when functional tests become available, the diagnostic details are often inadequate to give clear visibility on a given problem.ScanExpress JET is a tool designed to overcome these challenges by automating the functional test generation process on CPU–based IEEE-1149.1 compliant circuit boards. Coined JTAG Embedded Test, JET is the preferred method for at-speed, non-intrusive functional testing.
-
Product
Flight Control System Test Platform
Test Platform
The Flight Control System Test Platform provides a hardware in-the-loop (HIL) closed-loop test environment for dynamic and maintenance testing of Flight Control Systems (FCS) of both commercial and military aircraft. The system simulates control surface activities from multiple combinations of rudder, flaps, elevator, aileron, and engine controls to the FCS. The system delivers repeatable, cost-effective testing in a fraction of the time needed with typical in-house simulation test systems.
-
Product
Eagle Test Systems
ETS-200T
Test System
The ETS-364 is a general-purpose precision analog and mixed-signal test platform designed for high volume production testing of integrated circuits; optimized for high throughput applications with a fully integrated multisite software and hardware architecture.
-
Product
Standardize Production Test Software For PCBAs And Electronic Devices
test
The vast majority of test project man-hours are spent on software development, so the choices that teams make in software tools and architecture have significant impact on deployment schedules. Standardizing software across a team or organization increases both efficiency and proficiency, lowering the risk of missed deadlines and improving test quality and reliability. Test software must:
-
Product
Standard Test Systems
WaveCore™ Products
Test System
Textron Systems’ WaveCore family offers a variety of standard test systems with a primary application of satellite payload lab testing. Our systems can be deployed affordably for both production and engineering applications, providing industry-leading levels of data correlation with high system mean time between failures and low mean time to repair.
