-
product
Benchtop/TableTop Chamber
HIACC Engineering & Services Pvt. Ltd.
Built with corrosion-resistant stainless steel, the test space can hold specimen up to 100 kg. The refrigeration system uses low GWP refrigerant and meets all statutory standards. The chamber also comes with removable humidity water tank and direct water connection is also available
-
product
Ultra Fast Flexible Implantable Microprobe
IT-23
IT-23 Flexible Implantable Microprobe - For ultra fast measurements and for use on micro-size specimens. Time constant 0.005 seconds. Tissue Implantable with a 23 gauge needle (supplied). Fairly fragile. Sensor wires are twisted TFE Teflon™ insulated. Maximum Temperature 150°C. Isolated. Probe diameter .011", 3 foot lead.
-
product
Hydraulic Servo Control Compression Testing Machine (Four Column)
TYE Series
Jinan Testing Equipment IE Corporation
This series Servo-Hydraulic Compression Testing Machine is mainly designed for compression test of building material items, such as concrete cubes, cement specimen, paver materials and related component, etc. With new design idea and advanced technolog, this series has more advantages in appearance, operation & applications. The compression testing machine is an ideal tester for quality control at industrial & mineral enterprises, teaching in high schools, and technology researching at scientific institutes.
-
product
Vibration Testing
Vibration testing includes kinetic energy transfer to the test specimen, often described as the Device Under Test or simply DUT. Typically specified in terms of displacement, velocity, acceleration or the corresponding power spectral density units as a function of frequency. The form of the vibration may be sinusoidal, random, or a combination.
-
product
Climate Control Test Chamber
ACMAS's Climate Test Chamber is ideally suited for specimen test requiring quick changes of temperature. It covers various applications from JEDEC and IEC test standards. ACMAS Thermal Cyclic Chamber is equipped with advanced technology such as specimen temperature control which allows linear specimen temperature rates of change during rapid thermal cycling or accurate temperature ramp control. This chamber is also known as Climatic Test Chamber and Climate Controlled Test Chamber.
-
product
Heat Seal Tester
HST-01
Jinan Leading Instruments Co., Ltd.
HST-01Heat Seal Tester seals the specimen to determine the seal parameters of basicfilm, laminated films, coating paper and other heat sealing laminated filmsaccording to the requirement of relative standards. The seal parameters includeheat seal temperature, dwell time, and the pressure of heat seal. Heat sealmaterials that have different melting point, heat stability, fluidness, andthickness of could show various heat seal properties, which cause obviouslydifferent seal technique.
-
product
IEC61588 Mandrel Test Device
CX-KD13
Shenzhen Chuangxin Instruments Co., Ltd.
This Mandrel Test Device conforms to IEC60588-1 Fig6 and IEC60065 Fig14--16.The test shall be performed by fixing the specimens of thin sheets on a mandrel made of nickel plated steel or brass with smooth surface finish.
-
product
Walk-In Climatic Test Chamber
WEIBER climatic test chamber is ideally suited for specimen test requiring quick changes of temperature. It covers various applications from JEDEC and IEC test standards. The climatic chamber is equipped with advanced technology such as specimen temperature control which allows linear specimen temperature rates of change during rapid thermal cycling or accurate temperaThe walk in option provides facility to test large sized, heavy weight specimen as well as the facility to test the specimen in bulk. Capacities ranging from 2000 to 10,000 Lt are available. Standard as well as customizable sizes and facilities are provided.
-
product
Mixed Gas Corrosion Test Chamber
Guangdong Test EQ Equipment co., Ltd.
- Precision Gas Dosing: Delivers exact concentrations of corrosive gases (e.g., H₂S, SO₂, Cl₂ with N₂ carrier gas; NO₂ with synthetic air) for repeatable test conditions. Supports simultaneous dosing of up to four gases, enabling multi-pollutant interaction studies.- Acrylic (PMMA) viewing window allows real-time monitoring of specimens without compromising test integrity.- Pressure monitoring system and gas sampling port ensure operator safety and compliance with industrial hygiene standards.- Advanced Environmental Control: Integrated air exchange module maintains consistent gas distribution and replicates dynamic atmospheric conditions.- Standard Compliance: Certified for IEC 60068-2-60, 60068-2-42/43, ISO 21207, and other global protocols, guaranteeing internationally recognized results.
-
product
Brinell Hardness Tester
KB Series
Newage Testing Instruments, Inc.
The Newage KB Series is a popular, manually-controlled Brinell hardness tester that meets ASTM E-110. This lightweight, portable tester is ideal for virtually any size or shape of metal specimen.
-
product
Software Packages
GLUON
The software uses notched specimens (CT specimens) to evaluate the material elasto-plastic fracture toughness value (JIC). The test is conducted at constant loading rate under test-force control or CTOD control and the load is removed to calculate the crack length. The software plots graphs of the crack length increase (Δa) and crack growth resistance (J value) from the acquired data, calculates the JIC value, and evaluates its validity.
-
product
BenchTop Chambers
Nano Series
The Nano series of bench top chambers are designed for testing relatively smaller sizes of specimen. With a small foot print, this chamber is capable of performing low, high temperature and humidity tests.
-
product
Rubber Testing Machine
Dongguan Kejian Instrument Co., Ltd.
This machine is used to do the test of wear-resistant in surface, leather, cloth, paint, paper, flooring, plywood, glass and natural rubber. The method is using the standard knife cutting the specimen, and then using the regulated models of grinding wheel with loading weight to be abrased. Remove the specimen after rotation to reach a centain number, and then observe the condition of the specimen or compare the weight with the previous materials.
-
product
Stereo Microscopes & Macroscopes
Leica Microsystems offers customized stereo microscopes for research, industry and education. Our macroscopes for industry, medicine and research offer exceptional optics and ultra convenient operation. Stereo microscopes and macroscopes from Leica enable you to view, analyze and document your specimens in two and three dimensions for any application.
-
product
Needle Microprobe
MT-23/5HT
Fast-response 23 gauge needle probe, (needle length is 5 cm) for instant readings in tissue, semisolids, liquids. Also for very small specimens, powders and materials. Needle tip is sealed to ensure only stainless steel contacts specimen. Max. temp. 200°C. 5 ft. lead. Smallest microprobes give fastest reading. Short probes are easier to insert and last longer. Type #'s indicate needle gauge and needle length in cm.
-
product
DIN Abrasion Tester
Sataton Instruments Technology CO., Ltd
DIN abrasion tester basing on the rotating cylindrical drum is to determine the volume loss and abrasion resistance index due to the abrasion action of rubbing a specimen over a specified abrasive. It is the recommended testing machine to evaluate for abrasion resistance of rubber, vulcanized or thermoplastic materials. The tester includes a laterally movable specimen holder and a rotatable cylinder with abrasive sheet fixed can provide two testing methods, non-rotatable specimen test and rotating test piece.
-
product
Needle Microprobe
MT-D
Fast-response 29 gauge needle surface probe for locating inflammation, arteries, etc. Also for dental use. 1/4'' right angle needle length, 3/4'' needle distance from lead. 5.5'' long handle for ease of use. Needle tip is sealed to ensure only stainless steel contacts specimen. Max. temp. 200°C. 5 ft. lead. Sensor within .3mm of tip. Smallest microprobes give fastest reading. Short probes are easier to insert and last longer. Type #'s indicate needle gauge and needle length in cm.
-
product
Horizontal Flammability Tester
Sataton Instruments Technology CO., Ltd
Horizontal flame resistance tester is design based on FMVSS 302 to determine the burning behavior of materials as interior in motor vehicles by calculating the burning rate of the specimen after ignition by a small flame. Exposed to a certain flame for specified time, the specimen which is clamped in a U shape holder will be measured for the burned distance and time taken to burn this distance. The tester is particularly important for assessing safety of the materials used in the passenger compartment.
-
product
Meters For Contact Angle And Surface Tension
SURFTENS AUTOMATIC
Optik Elektronik Gerätetechnik GmbH
Automatic measuring instrument for contact angle and free surface energy with motorized pump, automatic drop placement and motorized specimen table (200 x 200) mm.
-
product
Pendulum Impact Testing Machine
Direct indication of impact energy absorbed by specimen on large diameterAvailable with safety guard for the operatorInitial potential energy for Charpy is 300 Joules & for Izod is 170 Joules with a L.C. of 2 Joules (for Analogueodels) & resolution of 0.5 Joules (for Digital Model)Pendulum drop angle for Charpy is 140° & for Izod is 90°ASTM Impact Testing machine is also supplied, which conforms to E-23 ASTM standarAvailable with Gauges, Tongs, Sub-zero bath, Templates, U & V-Notch milling cutter (Optional)
-
product
Plug-in Temperature Conditioners
PITC
The PITC, with a temperature range of -70 C to +177 C, was first introduced in the late 1950s by Bemcos Conrad/Missimer Division. Today, the modernized version of this system is the ideal solution where short run or infrequent tests are required, test specimens are unusual in size or shape, initial capital costs must be held low, or test needs are frequently changed.
-
product
Furnaces
These three zone resistance wire wound furnaces are of split construction to facilitate fast and easy loading of a pre-assembled specimen train. The case is constructed from stainless steel with aluminium and hardened insulation board end plates. The optional front cut-out allows the use of side-entry high-temperature extensometry. Adjustable stainless steel latches keep the furnace halves locked together during use, but are then easily opened once testing is complete. The furnace is available with optional heavy duty brackets or mountings, which attach to a wide range of testing systems. An extensive range of standard controllers is available to suit most test regimes. Custom variants can be specified should the standard range not include a suitable unit.
-
product
Contactless Laser Extensometers
Jinan Testing Equipment IE Corporation
Model LE-05 and LE-15 extensometers measure strain optically, without contacting the specimen, using laser diode technology. The extensometers are self-contained and portable. They may be interfaced with a variety of testing machines and data acquisition systems using the ±10V analog output or bi-directional RS-232 serial port. Operation may be local or remote. A digital display is included. The scanning beam is always perpendicular to the specimen, unlike most laser extensometers. This eliminates errors when viewing through windows in chambers. It also minimizes sensitivity to the distance between the extensometer and the sample. Because the unit measures reflected light, no receiver is required behind the sample.
-
product
Hydrostatic Head Pressure Tester
Sataton Instruments Technology CO., Ltd
Hydrostatic head pressure tester is designed to determine the resistance to water penetration of materials by hydrostatic pressure method. By measuring the opposition to the passage of water through the tested specimen, the tester is to provide standard testing conditions for operator to note the test terminal point. The tester is primarily intended for ducks, tarpaulins, tentings, waterproof materials and other materials which are used for impermeable application, such as chemical protective clothing or medical protective clothing.
-
product
High-end Transmission Electron Microscope
CryoARM
JEOL announces the latest member in its family of high-end transmission electron microscopes, the CryoARM. This highly automated TEM is designed for unattended operation and high throughput imaging of cryo-EM specimens. The CryoARM was initially introduced to a select audience at the 2016 Gordon Research Conference in Hong Kong, M&M 2016 in Columbus, OH and EMC 2016 in Lyon, France. The CryoARM is a dedicated cryo-TEM, based on the highly successful JEOL ARM (Atomic Resolution Microscope) series, an ultrahigh performance, highly stable platform considered to be the "best-in-class" TEMs. The development of the CryoARM was accomplished in collaboration with leading Life Science researchers.
-
product
Metal Wire Torsion Testing Machine
WTT Series
Jinan Testing Equipment IE Corporation
WTT series metal wire torsion tester is mainly used in a metal factory to test the plasticity of metal wires and ropes under torsion condition. Surface flaws of steel wires may be shown during the testing process. The revolution is displayed on a 4- digit LED, with the max. revolution value displayed as 999.9. The revolution value is automatically held at the break of specimens. With computer & software, the Metal Wire Torsion tester can realize automatic control. The Metal Wire Torsion tester conforms to standard ASTM A938, ISO7800. The Metal Wire Torsion tester is an ideal QC tool for Quality Inspection & Control Department related to steel wire application.
-
product
Advanced Hydraulic Wedge Action Grips
2742 and 2743 Series
The Instron advanced hydraulic wedge action grips deliver controlled, constant gripping force using an external hydraulic supply across static and dynamic testing. They support capacities up to 600 kN (static) and 500 kN (dynamic), with interchangeable jaw faces for round or flat specimens. The design ensures jaw face positions remain fixed during gripping (eliminating preload), compensates for changes in specimen thickness, and is ideally suited for use with metals, composites, and plastics.
-
product
Surface Water Absorption Tester
TF167
TESTEX Testing Equipment Systems Ltd.
Specimens are placed at an angle on the base of the apparatus. After water flows down the surface of each specimen, the amount of water retained by each specimen is measured. Six specimens are tested, three on the face of the fabric and three on the back of the fabric. The six observations are averaged to determine the surface water absorption of the fabric.
-
product
Impact Tester - Impact Testing Machine
Impact tests are used to measure the resistance to failure of materials to a suddenly applied force. The test measures the impact energy, or the energy absorbed prior to fracture. ToronTech™ offers advanced Impact testing machines to measure that energy through drop weigh tear test and Charpy impact test. We also offer machines for the preparation of specimens for these tests.
-
product
Walk-in Environmental Chambers
EWS-SERIES
Mono-block/Pre-fabricated design EWS-Series Walk-in Environmental Chambers with custom-built features to meet testing needs of large-sized test specimens
