-
product
20-50,000 Hz Charge Amplifier
203G8
The Trig-Tek™ 203G8 accepts pickupswith sensitivities varying from 1 to 110pC/g. It has three simultaneous outputs:Acceleration with a sensitivity of 100 mVrms/Pk g; Velocity with a sensitivity of 534mVrms/Pk/ips; and Displacement with asensitivity of 100 mV/mil DA.
-
product
Total Stations
Zipp02 Series
With vertical compensation and 2” accuracy the Zipp02 provides you with the precision required for your most demanding jobs at an affordable price without adding complexity. The Zipp02 is the tool of your choice when it comes to checking angles, alignments, grade work and short range leveling.
-
product
Test Line • Devices for measuring electrostatic charges
HAUG offers a wide selection of easy-to-use gauges. These are field charges with which electrical charges, fields and potential can be measured. The measured values show how strongly a surface is covered with an electrostatic charge.
-
product
Accelerometer (Charge Output Type)
NP-2000 Series
This sensor converts mechanical vibrations into electric signals in proportion of vibration acceleration.You can choose the one that is ideal for your purpose,conditions,applications etc. from wide variety of selection.Charge amplifier is necessary because it is a charge output type,however, compared to pre-amplifier built-in type, it can be used at higher temperature in general.
-
product
HEV & EV Power Tester
EVd-40
The EVd-40 Power Tester is a pre- and post-reconditioning tool for quality control of aftermarket HEV & EV battery production. The equipment integrates a “smart” charger (Sorensen XG 1700 or Kepco KLN 1500W) with NuVant Systems high power discharge electronics. The "power test" discharges battery packs at high power (10,000 watts), while tracking module voltages. The software monitors up to 40 module voltages at a time, identifying any weak modules. The "smart" charger performs charging constant current (CC), constant voltage (CV) and complex mixed mode constant current – constant voltage (CCCV) charging protocols at voltages up to 600 V. This enables recharge of any type of rechargeable battery.
-
product
DC Automated Accelerated Reliability Test Station (AARTS)
DC-HTOL
The DC Automated Accelerated Reliability Test Station (AARTS) systems are designed to maximize channel density. The first systems developed by Accel-RF (ARF) were intended for RF and DC stimulus to the Device Under Test (DUT). However, there are some applications in which RF stimulus is not required.
-
product
SCPA Relay Stations
Japan Communication Equipment Co., Ltd.
It is SCPA relay station system which receives the broadcast wave transmitted by the previous station, gives necessary processing, and sends.
-
product
Universal Total Stations
SPS730 And SPS930
Nothing else comes close. Trimble Universal Total Stations lead the industry in accuracy, range and reliability for fine grading, paving, stockpile scanning and site measurements.
-
product
Technical Manual Probe Station
4060 150-200 mm
Micromanipulator's Tech Series Probe Station, Model 4060 is designed to provide a quality 6-inch (150mm) or 8-inch (200mm) probe station at a cost effective price
-
product
Training Administrator Station
Model 8843
The Training Administrator Station (TAS), which can pair with up to four Model 8813 and/or Model 8833 training benches, is a remote controller that uses a touchscreen Microsoft tablet communicating over a closed WIFI network.
-
product
Controlled Environment Probe Station
CG-196
Everbeing controlled environment probe station allows vacuum and cryogenic probing down to 77K with liquid nitrogen or high temperature probing up to 1273K. Efficient in characterizing your devices at extreme temperatures, vacuum, specific gas, etc.
-
product
Module Testing Station
QuickSun® 550CE
QuickSun 550CE is certified by TÜV Rheinland and a detailed test report is included with every simulator proving Class A+A+A+ performance with respect to spectrum, irradiance non-uniformity and short term instability (STI). Long term instability (LTI) is also within Class A+ tolerances during the 40 ms long flash pulse. IV characteristics are recorded with an electronic load and proprietary electronics unit which measures voltage, current and irradiance signals when module is swept e.g. from short circuit to open circuit or vice versa.
-
product
Charge Logger Sensor
NUL-246
This sensor measures electrostatic charges. It can be seen as a highly sensitive electroscope indicating whether a charge is positive or negative. Other uses are: to explore the nature of static charge, to measure both charge and voltage, to measure charge by induction, quantify the charge on a capacitor or discover the charge distribution on a conducting sphere.
-
product
Fixed GEO Earth Stations
Kratos Defense & Security Solutions, Inc.
Kratos provides a broad range of fixed earth stations ranging from 3.5m to 18m and configured in receive-transmit or receive-only mode. These antennas offer outstanding electrical performance and exceptional versatility to support low PIM at certain Ku bands and all X-band systems.
-
product
Multiple Instrument Station
SYSTEM 8 MIS 4
The Multiple Instrument Station MIS4 provides you with all the instruments required for the test and measurement of electronic components and PCBs. ABI's SYSTEM 8 MIS4, along with the Ultimate software, is a faster and more economical solution than using traditional oscilloscope, metering and other bench test instruments, and can quickly produce the required Pass/Fail or other test and debug results.
-
product
Base Station Antennas
Fiberglass Collinear 118-960 MHz Omni Patterns - 500 Watts Standard connector is a recessed N-Female. 7-6 DIN available
-
product
Cellular Base Station Factory Test Systems
*Factory Test System*Designed and Built by BCO*100% Functional Testing*Environmental Stress Screening Testing
-
product
Station Self-Service Controller
Advantech's Self-Service Controller ITA-1000 series supports Station Self-service System. As a rugged system with compact size, low power consumption, and fanless design, our controllers specialize in rich I/O with excellent maintainability.
-
product
Silicon Charged Particle Radiation Detectors
ORTEC introduced the first silicon surface barrier detectors for charged particle spectroscopy in the early 1960’s. Since then, ORTEC has expanded the product line with more than ten different options to choose from.
-
product
Auto Bump/Calibration Station
PS500
Teledyne Gas & Flame Detection
To provide accurate performance and results, the PS500 has to be properly used and maintained. The Auto Bump & Calibration Station (ABC) provides bump testing, calibration and data management options and is compact, robust and intuitive to use.Two versions of the ABC are available allowing either a single gas cylinder or up to three cylinders to be connected. Additionally, a special three cylinder version is available for reactive gases.
-
product
Static Generators, Charging Bars and Pinners
The Generator/Bar System enables you to bond similar or dissimilar materials and holds materials in place, eliminates air pockets and wrinkles in multi-layer products, prevents plastic films from wandering on rewinders or shrinking on cooling cylinders, and increase production speeds.
-
product
Enhanced Probe Station
EB Series
Comprehensive prober for DC and RF. The EB series contains features to step-up your usability to acquire the accurate data you need from your devices. It has a built in probe card slot.
-
product
Data Logger for Weather Station, 4G
HD33MT.4
HD33MT.4 with 4G/3G/2G/GPRS modem. Optional Ethernet. Designed for solar power. Integrated charger. Data Logger for weather station - remotely monitoring temperature, humidity, atmospheric pressure, solar radiation, rainfall quantity, wind speed and direction. Calculating sunshine duration.
-
product
Radiator Test and Repair Stand, Type 2 (Two Station)
9001
The Radiator Test and Repair Stand, P/N 9001, meets all requirements of military specification MIL-S-4534C, is completely self contained and requires only connection to a source of shop air and gas to place in operation.
-
product
High Performance EV Battery Test System
Shenzhen Sinexcel RE Equipment CO., Ltd
The 6V series battery test system uses a full-bridge circuit topology with a higher digit sampling chip. It can provide higher precision and more dynamic test data, and can provide a complete test program for mainstream lithium-ion batteries and batteries with a variety of material systems such as sodium batteries.
-
product
High Voltage Test Station
High-voltage test stations place high demands on the safety aspect. We design these test stations in cooperation with our manufacturers as self-sufficient test systems.
-
product
Vantage Pro2™ Plus Stations
6162 & 6162C
*Solar Powered Integrated Sensor SuiteThe wireless, rugged outdoor sensor suite runs on solar power. A lithium battery provides backup at night and during cloudy, winter days. The cabled version receives power from the base station.*TemperatureCurrent inside and outside temperature, and for each of the last 24 hours. High and low temperature alarms.*HumidityCurrent inside and outside humidity, and for each of the last 24 hours. High and low humidity alarms.
-
product
Torque Station Pro
TS-8700
TS-8700 Torque Station Pro is torque measurement system for motor basic property with high precision and high response.In combination with the motor torque detector MT series with the TH series torque detector, it is possible to perform high-precision, high-response motor torque measurement with up to 5.12 kHz sampling and ± 0.1 % of accuracy.In addition, the high rigidity compact torque detector RH series (10 N･m/ 20 N･m) can be mounted on the MT series. It has achieved more highly accurate measurement with ±0.05 %/F.S.This system is ideal for measuring torque fluctuations of motors on-board such as EPS motors.
-
product
All-in-One Meteo Compact Station
HDMCS-100
A ready to use and easy to set up Automatic Weather Station. The AWS measures wind speed, wind direction, humidity, dew point, temperature, barometric pressure and rainfall.
-
product
HEV / EV / Grid Emulators and Test Systems
With Scienlab test systems and test software, Keysight offers customized test environments for the development and testing of electronic components according to hybrid and electric vehicle testing standards. Our solutions help you to accelerate your e-mobility applications from the battery, Battery Management System (BMS), inverter, the charging interfaces of Electric Vehicle (EV), and Electric Vehicle Supply Equipment (EVSE).
