-
product
2000 Amp DC / 1500 Amp AC Current Probe
DC2000
Our DC2000 Current Probe measures up to 2000 amps DC (as well as 1500 amps AC). Self-powered via our meter, so there are NO batteries that can run down during a measurement session.
-
product
1000 Amp High Accuracy Current Probe
HA1000
The HA1000 is our most accurate current probe. The HA1000 clamp-on current probe measures from 1 to 1000 amps AC.
-
product
High Accuracy 100 Amp Current Probe
HA100
The HA100 is a compact clamp-on current probe for smaller loads where compact size is important. Its measurement range is from 0.1 to 100 amps AC and is very small which is ideal for locking inside a crowded electrical panel during monitoring.
-
product
Source - 20 GHz Source with Amp Attenuator
RI8554A
Automated Instruments, Powerful Development Tools and Worldwide Support
-
product
48V / 250 Amp Load
BD15-48P-24/12
For Battery Discharge testing and Power Supply testing. This particular Load has been designed to operate with 12V, 24V and 48V Battery systems and is extremely cost effective.
-
product
Digital 125 Amp Battery Load Tester
6033
• Heavy load enables the 6033 to detect bad batteries missed by other electronic testers• Automatically computes the CCA of the battery under load• Kelvin connected digital meter displays the following values:• Current Battery Voltage• Maximum Voltage reading• Minimum Voltage reading• Automatic load cycle• PATENTED• Made in USA of US and Global Components
-
product
PXI Battery Simulator Module, 4-Channel, 5 Amp
41-754-011
The 41-754-011 and 43-754-011 are 4 channel battery simulators, capable of supplying up to 8 V and 5 A per channel. The channels are fully isolated from ground and from each other allowing series connection to simulate batteries in a stacked architecture. The isolation barrier (1000 V channel to GND and 750 V channel to channel) allows the module to be used as a battery stack representative of those used for vehicle propulsion..
-
product
PXI 2 Amp MUX, Single 8-Channel 8-Pole
40-635-004
The 40-635 2 Amp Multiplexer module is available in 9 standard configurations as well as 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.The module is suitable for signal routing in ATE and data acquisition systems. Connections are made via a front panel 78-way D-type connector.
-
product
Signal, Contact, ITA, QuadraPaddle, 5 Amp, 26-30 AWG
610138112
Primary mating contact 610138116. (May mate with other Receiver contacts, as well.)Available in twin-female, crimp/solder, twin male, and wire-wrap design, QuadraPaddle contacts are engineered for flexible interconnect options. Rated at 5 amps continuous (1250 VAC) with a 2 ounce insertion force, QuadraPaddle contacts provide 4 reliable points of contact per pin, outstanding electrical performance, and low mating force.Specifications Operating Voltage & Current 5 Amps Max. Continuous; 600 volt Max. use of wire Mil-W-16878/4Contact Resistance 25 mOhms Max.Measured at 50 mV @ 100 mADielectric WithstandingVoltage (DWV) 1500 VDC Min.Insulation Resistance 5000 MOhms Min.Contact Body BrassContact Plating 30µ” Au over 100µ” NiContact Termination Crimp/SolderCycle Life 20,000 CyclesRoHS Directive 2011/65/EU Status CompliantREACH Article 33 Status CompliantECHA Article 59 of Reach Regulation CompliantAVG Mating Force (lbs) 0.24
-
product
PXI 10 x SPST 10 Amp Power Relay Module
40-160-001
The 40-160 module has a choice of 10 x SPST, 20 x SPST or 10 x DPST Power Relays, suitable for switching inductive/capacitive loads up to 10A at 250Vac.Power Relay Modules are intended for switching heavy AC or DC loads or for slaving up to large external relays, contactors and solenoids.It is suitable for applications requiring switching of either mains voltage or DC current.
-
product
PXI 2 Amp Multiplexer, 8-Bank, 8-Channel 2-Pole
40-659A-102
Model 40-659A is an 8 Bank 8 Channel Multiplexer module with 2-pole switching, It uses high quality electromechanical relays and is suitable for switching signals up to 2Amp, 300VDC/250VAC. The 40-659 module is suitable for multiplexer applications where two signals are required to be switched simultaneously, for example send and return signals in a telecoms system. It is also suitable for applications where reed relay based multiplexers do not have sufficient power handling capability such as switching medium power AC or DC loads or for slaving external relays, contactors and solenoids.
-
product
Signal, Contact, ITA, TriPaddle, 10 Amp, 14-18 AWG
610110129
Primary mating contact 610110128. (May mate with other Receiver contacts, as well.)Specifications Operating Voltage & Current 10 Amps Max. Continuous (14 AWG)600 Volt Max. use of wire Mil-W-16878/4Contact Resistance 4 mOhms Max.Measured at 50 mV @ 100 mAContact Body BrassContact Plating 30µ” Au over 100µ” NiContact Termination Crimp/SolderCycle Life 20,000 CyclesRoHS Directive 2011/65/EU Status CompliantREACH Article 33 Status CompliantECHA Article 59 of Reach Regulation CompliantAVG Mating Force (lbs.) 0.41
-
product
AMP HOUND 2
AMP2
*Attach adapter to fuse or touch probes to top of the fuse to measure automotive amperage instantly without removing the fuse*Audible tone lets you know when you have connection with a fuse and if there is current present in the circuit; perfect for working on under-the-dash fuse boxes*Snapshot Mode and Tracking Mode allow easy component testing and parasitic drain location
-
product
PXI 19 x DPST Reed Relay 2 Amp
40-136-212
The 40-136-212 19xDPST reed relay module is part of our range of medium power, general purpose relay modules which are capable of switching voltages up to 200V and current up to 2A.
-
product
30 AMP Fuse Buddy Testers
FB305M
Can test circuit current up to 30 Amps - an easy way to check fuel pump amperage. Clever design allows for easy connection into fuse sockets. Fuse Buddy ends are molded into the shape of the fuse itself. During testing the fuse is removed and replaced into the Fuse Buddy. This way, the circuit being tested maintains fuse protection. Fuse Buddy stays put & won't fall out of the socket, like test probes do.
-
product
PXI 2 Amp Multiplexer, Single 32-Channel, 2-Pole
40-635A-002
The 40-635A-002 is a single 32-channel, 2-pole MUX and is part of a range of Multiplexer modules available in 9 standard density and 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC. The module is suitable for signal routing in ATE and data acquisition systems. Connections are made via a front panel 78-way D-type connector.
-
product
ITA, G3, 500+ Amps, includes Dedicated 500+ Amp Module
410105174
ITA, G3, 500+ Amps, includes Dedicated 500+ Amp Module.Contacts rated to 1500VDC for low duty test applications.Mating Receiver 310105172. (NOT compatible with other VPC Solutions)
-
product
Low Cost Microwave Wideband Electro-absorption DFB Transmitter (without RF Amp)
MT60 (40KHz~33GHz)
Hangzhou Huatai Optic Tech. Co., Ltd.
MT60 series microwave DML optical transmitter, are able to transmit 33G microwave RF signal with long distance, wide bandwidth, and flat responsibility. They provide an outstanding linearity fiber optical communication for analogue and digital wideband microwave application. Due to avoidance of using expensive coaxial cable or wave guide, there will be no limitation in transmission distance, which improves the signal quality and reliability of the microwave communication. They can be widely applied in microwave communication system such as remote wireless; timing and reference signal distribution, telemetry, measurement and delay line etc as well as 10Gb/s and 60Gb/s high speed communication system.
-
product
PXI/PXIe Power Relay Module, 6xSPDT, 20 Amp
40-166-101
The 40/42-166-101 is a PXI/PXIe high density power relay module with 6xSPDT switches rated at 20A. The 40/42-166 range is available with SPST, SPDT or SP4T switching configurations. It uses power relays which are suitable for switching loads up to 20A at 240VAC (SPDT & SP4T versions) or 30A at 277VAC (SPST versions).
-
product
PXI 2 Amp Multiplexer, Dual 8-Channel, 4-Pole
40-635A-007
The 40-635A-007 is a dual 8-channel, 4-pole MUX and is part of a range of Multiplexer modules available in 9 standard density and 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC. The module is suitable for signal routing in ATE and data acquisition systems. Connections are made via a front panel 78-way D-type connector.
-
product
PXI/PXIe Power Relay Module, 3xSPDT, 20 Amp
40-166-102
The 40/42-166-102 is a PXI/PXIe high density power relay module with 3xSPDT switches rated at 20A. The 40/42-166 range is available with SPST, SPDT or SP4T switching configurations. It uses power relays which are suitable for switching loads up to 20A at 240VAC (SPDT & SP4T versions) or 30A at 277VAC (SPST versions).
-
product
PXI 38 Channel 2 Amp Multiplexer Card
40-656-001
A 38-channel multiplexer, 2-pole switching, suitable for switching signals to 2Amp, 220VDC/125VAC. It offers the highest switching density in its class for medium power/ voltage signals. Specifically designed for switching POTS, ISDN or xDSL telephony signals. Bandwidth for most configurations is typically >25MHz. It is paired with a very similar module, 40-655-001, a multi-banked multiplexer.
-
product
PXI 2 Amp Multiplexer, 4-Bank, 16-Channel, 1-Pole
40-657A-001-4/16/1
The 40-657A-001-4/16/1 is a 4-bank, 16-channel, 1-pole MUX and is part of our range of High Density 2 Amp Power Multiplexer Modules available in a choice of configurations, containing up to 8 separate multiplexers, all 1-pole switching. They are suitable for switching signals to 110VDC/250VAC at 2Amps, 90W.
-
product
PXI 2 Amp MUX, Dual 8-Channel 2-Pole
40-635-106
The 40-635 2 Amp Multiplexer module is available in 9 standard configurations as well as 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.The module is suitable for signal routing in ATE and data acquisition systems. Connections are made via a front panel 78-way D-type connector.
-
product
500-Pin SEARAY Cable Assembly, Male to Unterminated, Ferrules, 2 Amp, 0.5m, 250 Port
A500RMR-F-5C050
The 500-Pin SEARAY connector is used on switching products to provide a very high density 2A connector solution that is suitable for use to 200VDC. This cable assembly is suitable for direct connection to Pickering Interfaces products. Unterminated connections are provided at the other end of the cable for a variety of applications. Screwlocks enable the SEARAY connector to be secured to its mating product.
-
product
Signal, Contact, Receiver, QuadraPaddle, 5 Amp, Male Adapter, .025" Round Post (Adapter Pin)
610138117
Primary mating contact 610138100. (May mate with other Twin Female contacts, as well.)Specifications Operating Voltage & Current 5 Amps Max. Continuous; 600 volt Max. use of wire Mil-W-16878/4Contact Resistance 25 mOhms Max.Measured at 50 mV @ 100 mADielectric WithstandingVoltage (DWV) 1500 VDC Min.Insulation Resistance 5000 MOhms Min.Contact Body BrassContact Plating 30µ” Au over 100µ” NiCycle Life 20,000 CyclesRoHS Directive 2011/65/EU Status CompliantREACH Article 33 Status CompliantECHA Article 59 of Reach Regulation CompliantAVG Mating Force (lbs) 0.24
-
product
PXI/PXIe Power Relay Module, 16xSPDT, 5 Amp, 50-Pin SGMC Connector
42-158-003
The 40/42-158-003 is a PXI/PXIe high density power relay module with 16xSPDT switches rated at 5A. User connection is via a 50-pin SGMC male connector. The 40/42-158 range is available in 8, 16, 24 or 32 SPST configurations with or without hardware interlock. Electro-mechanical power relays are used which are suitable for switching loads up to 5A at 250VAC.
-
product
PXI/PXIe Power Relay Module, 16xSPDT, 5 Amp, 50-Pin SGMC Connector, With Interlock
42-158-003-HI
The 40/42-158-003-HI is a PXI/PXIe high density power relay module with 16xSPDT switches rated at 5A and includes the hardware interlock option. User connection is via a 50-pin SGMC male connector, hardware interlock is via a 4-pin 00 series socket (mating plug is supplied).
-
product
PCI 2 Amp Multiplexer, Single 4-Channel, 8-Pole
50-635A-104
The 50-635A-104 is a single 4-channel, 8-pole MUX and is part of a range of PCI Multiplexer cards available in 9 standard density and 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
product
PXI/PXIe Power Relay Module,5 Amp, 50-pin SGMC Connectors
40-153-002-HI
The 40/42-153-002-HI is a PXI/PXIe high density power relay module with 36xSPST switches rated at 5A and includes the hardware interlock option. User connection is via 2x50-pin SGMC male connectors, hardware interlock is via a 4-pin 00 series socket (mating plug is supplied). The 40/42-153 range is available in 18, 25, 36 or 50 SPST configurations with or without hardware interlock.
