-
Product
Universal Breakout Test Fixture
CA-323
-
The CA-323 Universal Breakout test fixture was designed to provide, as the name suggests, a universal test solution for aircraft trouble-shooting. The unit gives the technician the ability to monitor (100) different conductors or open an individual conductor for simulation or measurement. Any avionics component can be extended and in many cases with only a voltmeter and oscilloscope the operation in question of the Unit Under Test can be determined.
-
Product
Platforms
-
The use of switching systems to route instrumentation and stimulus signals to appropriate test points on a unit under test has a very crucial role to play in most electronics test systems. The sharing of test resources, connection of calibration references, load management, and many other functions are all managed by the switching system, the switching system acts as the interface between the unit under test (UUT) and the test equipment.
-
Product
SWB-2810, 4x43, 1 A, Row Access, Reed Relay Matrix Module for SwitchBlock
781420-10
Reed Relay
4x43, 1 A, Row Access, Reed Matrix Module for SwitchBlock - The SWB‑2810 is a reed relay matrix module for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
Product
Jandel Test Unit
HM21
-
The Jandel HM21 Test Unit has six constant current settings between 100nA and 10mA, and can be used to measure voltages from 0.01mV to 1250mV.
-
Product
Connect Generators to the Grid
GridCode
-
DIgSILENT has developed a new verification tool called DIgSILENT GridCode. The software has been designed in response to the need to verify whether a conventional or renewable power plant is compliant with local Grid Code interconnection requirements on basis of generating unit tests. There is a new trend towards verification of requirements at the point of interconnection of a power plant using transient stability simulations with numerical models. An increasing number of Transmission System Operators are including model validation methods to quantify the risk and uncertainty when using these simulation models in stability studies. These new methods have been included in the DIgSILENT GridCode tool.
-
Product
Professional Cable Tester/Tracer with Tone Generator
TC-NT2
-
The TC-NT2 is a convenient and comprehensive cable tester for network professionals. Its powerful and user-friendly features enable network installers to accurately check pin configurations of various voice and data communication cables. The TC-NT2 includes a master unit that transmits test signals to its corre-sponding remote terminator to verify cable reliability
-
Product
High-Voltage Test Device
PGK 110 / 5 HB
-
Cable testing and diagnostics with the BAUR PGK HB. There are hardly any other longer-lasting, more robust and cost-effective testing devices than the two-piece high-voltage test devices from the PGK HB series. They generate continuous adjustable test voltages with mains frequency or optionally DC with positive or negative polarity. The display instruments for current and voltage, the safety control unit and the regulating transformer for the voltage are integrated in the operating unit.* Testing as DC or Dc testing device* Polarity of the DC voltage can easily be reversed* Robust and durable
-
Product
Professional Cable Tester
1EA560
-
Multifuncional tester with LCD display enables to show wire maps and combination of pairs and their lenghts. It also measure the lenght until the broken line / cable. It is suitable for CAT5, CAT5E, and CAT6 cables. With special interface is also suitable for testing of coaxial and telephone cables. It has special unit for testing of cable ends in the other room.
-
Product
High-Voltage Test Device
PGK 260 HB
-
Cable testing and diagnostics with the BAUR PGK HB. There are hardly any other longer-lasting, more robust and cost-effective testing devices than the two-piece high-voltage test devices from the PGK HB series. They generate continuous adjustable test voltages with mains frequency or optionally DC with positive or negative polarity. The display instruments for current and voltage, the safety control unit and the regulating transformer for the voltage are integrated in the operating unit. *Testing of medium- and high-voltage cables * DC voltage testing of up to 260 kV output voltage with positive or negative polarity * AC voltage testing - up to 190 kV for switchgear, busbars and insulating elements * Easy-to-maintain 2-piece design
-
Product
Multiple Output Bidirectional PSU
LAB-MOBI
-
Electronic Test & Power Systems
The LAB-MOBI is a series of multi channel High Power Bidirectional PSUs. Each system is able to operate as either a DC Source or a DC Electronic Load. This integrated approach features high dynamics enabling the user to switch seamlessly between quadrants. When sinking energy from the unit under test the LAB-MOBI automatically inverts the DC to AC and synchronises this output to the grid. Dedicated application modes are available for battery cycling and emulation, which can be used to implement specific test routines. Other common applications the LAB-MOBI is used for include testing electric motors, fuel cells, super capacitors and solar panels. Max. Volt. Output 1000V,Min. Power 60kW, Max. Power 500kW.
-
Product
USB JTAG controller
-
The small, lightweight design means the XJLink2 can easily be moved to the Unit Under Test (UUT). Advanced features, like their programmable JTAG signal pin position, switchable power supply and auto signal skew, make it easy to connect to a wide range of circuit boards. Simple to install and use due to the USB plug-and-play ability.
-
Product
JTAG 3rd Party Controller Support
-
Corelis offers support for a variety of devices and instruments from third-parties in an effort to provide existing test platforms comprehensive JTAG test execution with Corelis ScanExpress software products. Supported instruments include National Instruments PXI-655x HSDIO and Teradyne Di-Series modules. Corelis also provides support for JTAG testing with FTDI FT2232 ICs embedded on a unit under test (UUT).
-
Product
Test System
Tessy
-
TESSY automates the whole unit test cycle including regression testing for your embedded software in C/C++ on different target systems. As an easy-to-install and easy to operate testing tool TESSY guides you through the unit test workflow from the project setup through the test design and execution to the result analysis and reporting. TESSY takes additionally care of the complete test organization as well as the test management, including requirements, coverage measurement, and traceability.
-
Product
C and C++ Testing, Static Analysis, Code Review
C++test
-
Parasoft C++test is a complete C/C++ developer's quality suite for static code analysis, code review, automated unit and component testing, coverage analysis, and regression testing ? on the desktop under leading IDEs and in batch processes. Available for common enterprise and embedded environments.
-
Product
Glove And Sleeve Testing Equipment
-
Hanco's glove and sleeve test units are designed for the ultimate in convenience, efficiency and performance. The unit's versatility is unmatched. Each unit is equipped to test Class 00 through Class 4.
-
Product
8-CH 14-bit 100 MS/s High-Speed PXI Express Digitizer
PXIe-9848
Digitizer
The ADLINK PXIe-9848/9848H is an 8-channel, 14-bit, 100 MS/s digitizer delivering both high-accuracy measurement results and high-dynamic performance. With a PXI Express bus interface and ample onboard acquisition memory up to 512 MB, the PXIe-9848/9848H can easily manage simultaneous 8-CH data streaming. High density and high speed digitizer features ideally position the PXIe-9848/9848H for applications such as LIDAR, radar signal acquisition, and PSU (Power Supply Unit) testing applications.The PXIe-9848 provides a flexible set of input ranges from ±0.2V to ±2V, software selectable 50Ω or 1MΩ input impedance, a wide variety of triggering options and tight synchronization capability, all maximizing convenience of use. In addition, ADLINK provides the PXIe-9848H, features a x15/x50 signal condition module providing both high input voltage range of ±100V and high dynamic performance, delivering the optimum solution to measurement range expansion in a PXI system.
-
Product
Energy Saving System
ECO-Vibe neo
-
ECO-Vibe neo has been designed for an eco-friendly vibration test system. The test conditions with a vibration test system depends on a unit under test. Generally, the exciting force required for performing a vibration test can be calculated by the product of mass (e.g. test article, jig, table, etc.) and test acceleration. But, when the required exciting force is smaller than the maximum rated exciting force of the vibration test system, the field power supply that the constant current has to be continuously provided to produce the DC magnetic field constitutes a large part of power consumption compared with the drive power for the moving element. ECO-Vibe neo can reduce the power consumption by choosing the exciting force in this case. In addition, you can enjoy a reduction merit of the running cost from the first year when the system is introduced because initial cost is zero.
-
Product
AOI Handlings System
-
The AOI handling system is a compact facility with various test units. Via an ionization cleaning station the ceramics are transferred to the contacting station. There, the resistance values of the substrates are tested with a rigid needle adapter. Afterward, the ceramics are further conveyed to the three (optionally four) AOI test stations (for automatic optical inspection) and are tested for cracks, unevenness, faulty imprints, contamination, etc. The poorly evaluated ceramics arrive at a review station where the operator can assess and evaluate the errors on the monitor. If the operator is uncertain about a fault, the ceramic in question can be positioned under the microscope position and inspected by eye. Poorly defined ceramics are marked accordingly with an ink pen.
-
Product
Intermittent Fault Detection & Isolation System
IFDIS
-
The IFDIS™ uses patented Intermittent Fault Detector technology that simultaneously and continuously monitors every circuit path within a Unit Under Test (UUT) - such as a Line Replaceable Unit (LRU) chassis' interconnects - for intermittent continuity failures that occur for as short as 50 nanoseconds. This state of the art technology is combined with an environmental chamber and vibration table, which simulate the UUT’s operational environment and cause intermittent faults to manifest, creating a system that is unsurpassed in intermittent fault detection.
-
Product
PON Fiber Optical Monitor System
PON FOMA
-
PON FOMA ( PON Fiber Optical Monitoring Alarm System) is integrated RTU ( Remote Test Unit )、Center Monitoring Server and its management software to be integrated operation、remote control、periodic fiber scan、predictive analysis and support the instant fiber with status information and alarm warning, accurate of long-term fiber data record, fiber analysis and management. RTU monitoring station is embedded Linux system which is with the advantage of high security, stability, efficiency.
-
Product
RF Microwave Switch Matrices
-
RF Microwave Switch Matrices provide automatic routing of RF microwave signals between test instrumentation and the unit under test (UUT). They provide consistent signal paths, enable automation of tests, and often include signal conditioning.
-
Product
C++ Test Aider
Testwell CTA++
-
Testwell CTA++ is a tool for unit testing C++ classes, libraries and subsystems. The tool is easy to use and provides very powerful features helping the tester to build the testing environments and running the tests on C++ code. Testwell CTA++ is used for building testing environments, test beds, for the code under test (C++ classes, libraries, subsystems, APIs) and then executing the tests with the test bed.
-
Product
SWB-2834, 8x34, 2 A, Electromechanical Relay Matrix Module for SwitchBlock
781420-34
Relay Matrix Module
8x34, 2 A, Electromechanical Relay Matrix Module for SwitchBlock - The SWB‑2834 is an electromechanical relay matrix card for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
Product
SpaceWire Physical Layer Tester
141
-
The SpaceWire Physical Layer Tester (SPLT) is a tool designed to test, validate and verify a SpaceWire system across all levels of the SpaceWire standard. Two SpaceWire ports employ a special LVDS interface which allows the transmitted signals to be deliberately and measurably manipulated to test the capability of a unit under test to receive signals of varying quality.
-
Product
SWB-2810, 4x43, 1 A, No Row Access, Reed Relay Matrix Module for SwitchBlock
781421-10
Reed Relay
4x43, 1 A, No Row Access, Reed Matrix Module for SwitchBlock - The SWB‑2810 is a reed relay matrix module for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
Product
C++ Test Framwork
Google Test
-
a unit testing library for the C++ programming language, based on the xUnit architecture. It can be compiled for a variety of POSIX and Windows platforms, allowing unit-testing of C sources as well as C++ with minimal source modification.
-
Product
Test Program Execution for High-Volume Production Systems
ScanExpress Runner Gang
-
Electronic manufacturing test systems must be fast and efficient. Schedules today are shorter, products are more complex, and the market demands higher speed—the product needs to be built and shipped yesterday.ScanExpress Runner Gang Edition is a concurrent boundary-scan and in-system programming test executive designed specifically for high volume production. Unlike traditional test systems which execute sequentially on a single unit under test (UUT) at a time, ScanExpress Runner Gang Edition provides concurrent (gang) testing on up to 8 UUTs for improved test and programming times.
-
Product
Test Extension Boards
XJIO
-
The XJIO boards are expansion units that enable you to improve the test coverage for a Unit Under Test (UUT) by verifying the signals right through to the external connections. They will integrate with your XJTAG test system to provide access to otherwise inaccessible areas of your circuit. With a range of digital and analogue I/O pins on the board, you can improve fault isolation, verify power rail levels, and dispense with costly custom test jigs - even for non-JTAG boards.
-
Product
Primary Injection Test Equipment
-
High current injection units for primary testing of over current relays and circuit breakers.
-
Product
Multi-Interface TDM, Optical, And Packet/IP Rackmount & Probe Test Platforms
mTOP™
-
Most equipment manufacturers and large enterprises prefer rack-based test tools as they are compact and higher density form factor solution for testing, monitoring, and troubleshooting network conditions. GL’s Multiple TDM Optical and Packet (mTOP™) rack enclosure can house any combination of USB based test equipment which are easily deployed and securely fixed to an equipment rack to provide extraordinary scalability to test switches, routers and end-to-end networks. These rack based platforms incorporates the basic test unit along with the necessary PC hardware, Windows® 10 64-bit operating system and remote accessibility via scripting and remote desktop. There are no moving parts with the unit, so reliability and longevity are integral. GL’s latest mTOP™ Probe stand-alone hardware variant is an all-in-one self-contained test instrument. The mTOP™ Probe can include any of the multiple TDM Optical and Packet interfaces USB device combined with the PC into one single box. The comprehensive mTOP™ Probe hardware unit is designed for easier portability and convenient for field testing which incorporates the testing features for multiple interfaces along with necessary PC hardware in a single box. GL’s USB based test equipment - PacketExpert™ (Ethernet), tProbe™ (T1/E1), USB T3/E3 (TDM), Dual UTAs (Analog/Wireless), and LightSpeed1000™ (SONET SDH) to support multiple interfaces in a compact rack space or included in a portable Probe unit.
