Filter Results By:
Products
Applications
Manufacturers
- Pickering Interfaces Inc.
product
Single Bus 36-Channel 2A PCI Fault Insertion Switch
50-190-201
This PCI fault insertion switch range is available with 75, 64 or 36 channels. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers. The Stimulus/Measurement to UUT path is suitable for supporting CAN and FlexRay bus systems.
-
product
PXI Source Measurement Unit
PX773x
The PX773x is a high precision, high speed source and measurement unit, which is designed for automated high throughput testing.
-
product
Dummy Load
Dummy load is capable of dissipating four times the legal limit 6 kW for 2 minutes and legal limit 1500 watts key down, forever. It covers the 160 meter to 6 meter bands (actually 1 Mhz-60 MHz continuously). It is a dry dummy load intended for testing amplifiers and station conditions. Two fans on the rear of the unit are automatically turned on when the internal temperature reaches 120°F/49°C . The unit runs off a universal AC supply. Simple to operate and use, the dummy load includes an RF sample output of -60 dBc.
-
product
Battery Management (BMS) Environmental Test System
The BMS Environmental Test System is a configurable platform simulating the essential signals used by Battery Management Systems (BMS) and cell-monitoring modules with the ability to perform environmental testing on multiple BMS units simultaneously. The system implements single-point value testing to evaluate specific BMS functions such as cell over and under voltage scenarios, cell leakage current, lost communications, or faulty system IO.
-
product
Franklin Tester
Model FT1
The Franklin tester FT‐1 is designed to measure the surface insulation resistivity of electrical steel sheet according to the ASTM Standard A717 and IS:649. This test method is suitable for quality control in the application of insulation coating. For ease of testing FT‐1 automatically set 300 PSI pressure on the sample by the inbuilt hydraulic unit and it is capable to set the desired test temperature of the platform. Then the regulated supply of 0.5V gets on and the current flowing through the insulation get measured. The calculated insulation resistivity will be displayed on graphics LCD display and as well as on printed report via thermal printer.
-
product
MCB Thermal Trip Calibration Test Bench (IEC 60898 Cl 9.10.1.2, Annex I.1, IS)
The test system is designed and customized to carry out 2.55*Intest as per Table 7 (test c) of IEC 60898 (also mentioned for routine testing of MCBs. The test is done at dc current to exactly analyze and correct the bimetallic properties of the MCB as far as thermal tripping is concerned. The unit comes with a pneumatically operated test fixture with in-built dc stepper motor that is controlled by a micro controller / PC to calibrate the breaker into a narrow tripping band programmed by the user.
-
product
Handheld Water Quality Meters
LAQUA WQ-320-K
- Dual channel- Large colour graphic LCD screen (70 x 52 mm) with backlight - Built-in foldable meter stand- IP67 waterproof and dustproof- Battery and USB powered- Eco-friendly, shock-proof, scratch-resistant, and non-slip- Built-in sensor holders- Efficient sensor locking mechanism- Sensor's LED light as reading stability indicator- No sensor adapter needed for attaching multiple sensors together- Compatible with conventional electrodes having BNC and phono connectors and long cables- Sensor status indicator- Temperature sensor indicator- °C & °F temperature units- Sample ID setting- Detailed calibration data- Auto stable, Auto hold, and Real time measurement modes- Customizable meter kit - up to 15 meter-sensor kit combinations- Hands-free testing- Ergonomic design- Multi-language options- Versatile channel and adaptive display- Up to 2 simultaneous calibrations and measurements- Automatic sensor recognition function- Data transfer via USB or wireless communication- Printer communication- 3 years meter warranty
-
product
High Low Temperature Test Chamber
The high low temperature test chambers from Weiber are climatic test chambers, designed to simulate highly precise high and low temperature environments for the testing of electrical and electronics items, metallic products, automobile parts, food items, biological samples, chemicals, building materials and other wide variety of processed and packaged goods. These test chambers find widespread usage in manufacturing units, quality control units and scientific research organizations and are commonly employed for heat endurance test, cold endurance test and humidity and dryness endurance tests of products. These tests help in determining the product performance in specific environments and also help in identifying any manufacturing flaws and in determining its stability and shelf life.
-
product
Sauter Force Gauges
Force gauges provide a quick and reliable way to obtain a measure of force in tension and compression. DMV UK offer a comprehensive range of mechanical and digital force gauges with selectable units and peak force capture with capacities from 2 N to 100,000 N. All gauges are supplied with standard accessories, a 2 year warranty, and can be used for force testing in hand held or test stand applications.
-
product
Raptor Primary Test System
The Raptor system consists of a main ‘master’ unit and a number of optional units that enable the execution of virtually any commissioning or routine testing jobs on the primary equipment of medium and high voltage electricity installations.
-
product
High Temperature Hot Mountable Furnace Extensometers (1200 Cor 1600 C)
Model 3549
Jinan Testing Equipment IE Corporation
The Model 3549 is a major advancement in the design of externally mounted, furnace extensometers. This new extensometer is designed to meet the stringent requirements of strain controlled testing as prescribed in ISO 6892, while introducing many new innovative features that help improve productivity with static testing applications (tension and compression testing) and long term testing such as low cycle fatigue and creep. The overall design reduces any influence from common lab environment vibrations. This unit also incorporates a new feature that allows the user to precisely set the contact force against the test specimen. This allows for even and repeatable contact force, limiting contact force induced errors. This extensometer mounts on a slide bracket (included) that can attach to the load frame of your test system; optional load frame mounting brackets are available. The gauge length for the 3549 is automatically set prior to mounting on the test specimen, which allows for hot mounting after thermal equilibrium has been reached.
-
product
Cable Tester
KT-45
Quickly test twisted cable RJ45 and BNC connector including T568A/B, 10-Base-T (UTP/STP), Token Ring, etc. Automatic test for open circuits, shorts, reversals, miswires, continuity. Main unit and one remote allow one person to test. Includes protective leather pouch. Testing before and after installation
-
product
High-Voltage Test Device
PGK 110 / 5 HB
BAUR Prüf- und Messtechnik GmbH
Cable testing and diagnostics with the BAUR PGK HB. There are hardly any other longer-lasting, more robust and cost-effective testing devices than the two-piece high-voltage test devices from the PGK HB series. They generate continuous adjustable test voltages with mains frequency or optionally DC with positive or negative polarity. The display instruments for current and voltage, the safety control unit and the regulating transformer for the voltage are integrated in the operating unit.* Testing as DC or Dc testing device* Polarity of the DC voltage can easily be reversed* Robust and durable
-
product
SFP Based Fiber Optic Test Solution
Eye-BERT Micro
The Eye-BERT Micro is a low cost, easy to use, all-in-one SFP based fiber optic test solution offering high performance bit error rate testing at a fraction of the cost while providing a rich set of features not found in other bit error rate testers. Features include: variable bit rate, user programmable patterns, and optical power and temperature monitoring (per SFP capability). Additionally, with a click of a button, the Eye-BERT Micro will automatically test an SFP module based on the information it reads from the module and generate a detailed test report complete with manufacturer, part number, serial number, date code, fiber type, link length, speed, and test results. The Unit is supplied with anti-skid bumpers and is small enough to be integrated into larger systems for dedicated link verification.
-
product
Keysight Dual 1x2 SPDT Terminated Microwave Switch Module for 34980A
34946A
The Keysight 34946A microwave switch for the 34980A Multifunction Switch/Measure Unit offers bi-directional switching for test signals from DC to 26.5 GHz. These switches provide excellent insertion loss, isolation, and VSWR specification. The microwave switches are configured as two independent 1x2 (SPDT) terminated switches on a single module. For general-purpose microwave switching applications, the module can be used to switch separate signal sources for a multi-band receiver/transmitter testing application.
-
product
PAT TESTER
Precision Mastech Enterprises Co.
The Safety Pat Plus is a handheld battery powered unit suitable for carrying out electrical safety tests.Stores 300 test results and can be battery & mains powered. The instrument is capable of testing surge protected equipment & can test 110V, 230V appliances. It will return true leakage results at both 110V and 230V
-
product
Adapter
EXC-1553UNET/Px(S)
The EXC-1553UNET/Px is an intelligent, single - or - dual channel, MIL-STD-1553 adapter. Its small size and ability to interface through USB or Ethernet interfaces make it a complete solution for developing, testing and performing system simulation of the MIL-STD-1553 bus, both in the lab and in the field.The EXC-1553UNET/Px shares its API with the entire Px family so that applications currently running on PCI, PCIe, ExCARD or PCMCIA boards will run without change on this device.Multiple units can operate via USB ports on the same computer. In addition, multiple units can operate on the same network, by programming each one with a unique IP address, and can be accessed from any computer on the network.
-
product
Sencha Test
Sencha Test is the most comprehensive unit and end-to-end testing solution for Ext JS apps. Based on years of testing Ext JS applications and the deepest integration with the framework, Sencha Test helps you improve application quality, accelerate time to market, and reduce testing time and costs. With Sencha Test, you can create unit and end-to-end tests quickly, and execute them on multiple browsers simultaneously. Cross-browser testing is critical to ensuring quality for organizations, and test automation is a requirement to meet delivery timelines. Sencha Test is the only dedicated testing solution for Ext JS applications. It helps you build an end-to-end testing plan without having to cobble together testing tools.
-
product
Proving Units for High Voltage Testing Equipment
A high quality range of proving units provide the important role of verifying the safe operation of high voltage potential indicators used by power engineers, maintenance personnel and service engineers. The proving units are essential tools for testing HV equipment before and after use.
-
product
Low Power Programmable AC Source
61600 Series
Chroma Systems Solutions, Inc.
Power:500VA (61601)1000VA (61602)1500VA (61603)2000VA (61604)4000VA (61605)Voltage range: 0-150V/0-300V/AutoFrequency: 15Hz 1000HzCompact size and weight attributable to advance PWM technologyBuilt-in PFC, provide input power factor over 0.98 (full load)AC+DC output mode for voltage DC offset simulationProgrammable slew rate setting for changing voltage and frequencyProgrammable voltage, current limitOne-key recall for 9 different voltage and frequencyLow output impedance for testing IEC 61000-3-2 ( 61605 )Comprehensive measurement capability, V, Irms, Ipk, Inrush, P, Q, S, PF, CF of current and etc.High output current crest factor, ideal for inrush current testingTurn on, turn off phase angle controlTTL signal which indicates ON/OFFAnalog programming interface3 units combined to 3-phase power outputEasy-use software for operation and ON/OFF testOptional GPIB and RS-232C interfaceFull protection: OP,OC,OV and OT protection
-
product
6 Sided Bed of Nails Testers
BoxProber Family
6 sided Bed of Nails circuit board test fixture. Probes top bottom and all 4 sides. Central camming mechanism pull plates inward. Mechanically or electrically actuated options. Designed primarily for testing products in plastics. Side access electrically probes outside panel connectors. The unit will also optically read LEDs and key segments off LCD displays. Solenoids will press buttons and servos will turn selector switches. DC motors are used to adjust multiple turn potentiometers. Microphone will detect audio output tones. Top and bottom of circuit boards can also be probed if removable access panels are available. This unit will also probe all 6 sides of a circuit board. This is typically utilized in applications where connector testing is required.
-
product
Benchtop Communication Test System
ATS3000A
The ATS3000A is designed using Astronics Test Systems’ proven Synthetic Instrumentation architecture. Featuring 23 instruments, and both Automated and Standalone modes to test, record, and diagnose faults, the unit provides complete RF, Analog and Digital capabilities. The ATS3000A also includes the sophisticated IF and baseband I/Q Digital Signal Processing required for modern radios. The fieldupgradeable, software-defined architecture features easy-touse graphical user interfaces and enables testing with minimal operator intervention. Test Program Sets areavailable for a full range of tactical radios, or you can create new TPSs easily using the included TestEZ® software suite.
-
product
Automated Testing for SAP
Autonomous Testing℠ for SAP
Designed for your SAP environment, Panaya Test Center is an integrated end-to-end testing platform, covering the entire functional testing spectrum including Unit Testing, System Integration Testing, Regression and UAT.
-
product
Optical Fiber Cable Tester (M/F)
T020-001-SC62
The T020-001-SC62 FC to SC 62.5/125 Adapter converts a native FC fiber female port on the Tripp Lite T020-001-PSF Multi-Function Optical Fiber Cable Tester to an SC female port for 62.5/125 multimode cable testing. “62.5/125” is clearly labeled on the unit to differentiate the T020-001-SC62 from other adapters. Included dust caps keep the connectors clean when not in use.
-
product
Long Travel Extensionmeters
The Instron model XL (long travel) extensometer is a precise device for measuring strain in highly extensible materials such as elastomers, semi-rigid plastics and films. Designed for use with electromechanical testing instruments, Instron XL units can be used to measure specimens elongation's up to 10 in or 250 mm. An optional of 15 in or 375 mm travel is also available.
-
product
Pressure/Vacuum Calibrators
Compact, completely self-contained unit designed for calibrating and testing pressure gauges, transducers, pressure switches, and other pressure-sensitive instruments up to 2,000 psi with an accuracy of ±0.25% of full scale.
-
product
High-Voltage Test Device
PGK 70 HB
BAUR Prüf- und Messtechnik GmbH
Cable testing and diagnostics with the BAUR PGK HB. There are hardly any other longer-lasting, more robust and cost-effective testing devices than the two-piece high-voltage test devices from the PGK HB series. They generate continuous adjustable test voltages with mains frequency or optionally DC with positive or negative polarity. The display instruments for current and voltage, the safety control unit and the regulating transformer for the voltage are integrated in the operating unit.* Testing of medium- and high-voltage cables* DC voltage testing of up to 70 kV output voltage with positive or negative polarity* AC voltage testing - up to 55 kV for switchgear, busbars and insulating elements* Easy-to-maintain 2-piece design
-
product
Java Testing Framework
TestNG
TestNG is a testing framework using annotations to provide a more powerful way to test your code in various ways: unit, regression, functional, integration, etc… TestNG allows you to clearly separate your Java code from the way your tests are run. You never need to recompile any of your classes if you decide to run a different set of tests or suites.
-
product
IP / VoIP Analysis & Simulation
GL offers high density Ethernet/IP tester variant which includes mTOP™ 1U/2U rack mount enclosures within which PacketExpert™ portable USB units are stacked to provide high density GigE ports form factor solution for testing GigE switches, routers and network conditions.
-
product
Digital Psophometer
Model 1072
Aplab Psophometer is a portable unit designed for the use of testing telecommunication equipment. It has Psophometric filter, which has the frequency response of the weighing network based on the CCITT recommendations and frequency response characteristics for unweighted measurements. The additional features included in this model are, ‘Recorder out’ available at the rear panel for plotting a response curve, built-in stable calibration signal for calibration check and Lo Battery facility to check the Battery condition.
-
product
Test & Measurement
Blonder Tongue Laboratories, Inc.
Tools to assist in video delivery installations, Blonder Tongue’s collection of Test & Measurement handheld products are second to none in capturing data for troubleshooting and testing purposes. These units provide real-time spectrum analysis, making them invaluable to those in the field.
