PCB Adapters
-
product
PCI to PC/104+ Bus Adapter
327/328
Model 327 and 328 are bus-to-bus adapters that allow operating a PCI board from a PC/104+ card stack. They allow selection of important PC/104+ signals using jumper plugs, thereby avoiding the requirement of using hardwired settings. Model 327 aligns the PCI board parallel to the PC/104+ boards, while model 328 places it perpendicular.
-
product
Adaptive Target Recognition System
Information System Technologies Inc.
ISTI’s adaptive target recognition, detection and classification system for sonar imagery can learn in-situ from expert operators’ feedback in order to yield better accuracy and flexibility in making decisions in new environmental and operating conditions. The developed system is based on the intuitive concept of image retrieval, where images submitted to the system are matched to learned images via a similarity measure. An information-based selective sampling measure chooses the new patterns to be used in the in-situ learning.
-
-
product
RS232 I2C Adapter
12C Master
*I2C frequency adjustable up to 400kHz*I2C level shifter, I2C level from 2V to 15V*Interrupt input for external events*Simple software interface (ASCII commands)
-
product
Digitizer Adapter Module For FlexRIO
Digitizer Adapter Modules for FlexRIO can be used with a PXI FPGA Module for FlexRIO or the Controller for FlexRIO to create a high‐performance instrument with customizable firmware. With sampling rates from 40 MS/s to 3 GS/s and up to 32 channels, these modules cover a wide range of requirements for both time- and frequency‐domain applications. Digitizer adapter modules also provide digital I/O capability for interfacing with external hardware.
-
product
Connector Adapter
MCA-ST connector adapter for the connection of micro plugThe connector adapter allows the direct connection of fine-pole connectors on circuit carriers or jumpers. The adapter is guided over the connector housing, which overcomes the tolerances of carrier and mounting.
-
product
High density PCB connectors
MHD/MDD/MDP Series
Smiths Interconnect's MHD/MDD/MDP series is an ESA qualified, high density board to board and board to wire interconnect available in up to 400 positions, with available insulators to accommodate coax and power contacts.
-
-
product
Passive XMC-to-PCI Express Adapter
6066
Our Passive XMC-to-PCI Express Adapter +5VPWR 4X (6066) is designed to adapt a single-wide XMC card to a 4X PCI Express slot. The 6067 supports P15 only and allows access to PN4 signal via the adapter's DIN connector. The A and C rows of a 96-pin DIN connector connect with the 64-pin user I/O connector (J4/P4) on the mezzanine card.
-
product
Adapter Kit, 3.5 mm
83059K
The Keysight 83059K adapter kit includes the 83059A 3.5-mm male adapter, the 83059B 3.5-mm female adapter, and the 83059C 3.5-mm male to 3.5-mm female adapter.
-
-
product
XMC-to-PCI Express (PCIe) Adapter
9956
The Technobox XMC-to-PCI Express adapter with Rear I/O support permits use of a standard VITA 42.3 air-cooled XMC or VITA 20 conduction-cooled XMC in the smallest possible edge finger PCI Express form factor. The length of the adapter is the length of the XMC and 10 mm mezzanine stacking height is supported. The height is a standard PCI Express board and is not the low-profile version.
-
product
Osprey PCI Unibus Adapter
9793
Dual-height card plugs into PDP-11 Unibus backplane. Fibrechannel cable plugs into Unibus logic connector on Osprey /TXP I/O Adapter logic provides Programmed I/O and DMA access to "real" Unibus compatible controllers (those not otherwise emulated).
-
product
25-Pin D-Type Male Straight PCB Mount
40-963-025-SM
Accessory allows a user to create their own PCB based termination solution mounted directly on the front of the product or on the end of a cable. Interfacing PCBs should be designed with suitable clearances for the voltage the application requires. 25-Pin Female connectors can be directly mated to a corresponding Pickering Switching Module while Male versions can be used to interface to a Female cable assembly termination.
-
product
Pull-Thru Adapter, Wired, QuadraPaddle, 90 Series, 2 VHDCI Male
510140158
Pull-Thru Adapter, Wired, QuadraPaddle, 90 Series, 2 VHDCI Male.
-
product
Test Adapter / Extender
The test adapter is used for measurement and testing of test specimen boards, which gives optimal access of signals, address lines as well as power from backplane assembly.
-
product
50-Pin D-Conn Female Straight PCB
40-963-050-SF
Ideal for user created termination schemes where the termination is to be on the front or remotely connected to the module by cable. Suitable cables for this product are detailed in the data sheet. Interfacing PCBs should be designed with suitable clearances for the voltage the application requires.
-
product
Wireless Airflow Temperature Humidity Adapter
DTHA2
UEi Test & Measurement Instruments
Airflow Temperature Humidity Adapter with Free App
-
-
product
Wearable Wireless Adaptive Refractor
VisionFit SC
The VisionFit SC is an innovative, electronic, mobile and wearable adaptive refractor.It performs a subjective sight examination and effectively replaces both the trial frame and the manual/electronic phoropter functionalities. VisionFit SC enables examining in free posture. Subjective refraction can be performed with the patient in his/her usual working environment and posture.VisionFit SC does not require the control of the patient’s position making it ideal for non-cooperative patients. Thanks to its comfortable and small footprint, this device reduces the examination time and increases the peripheral vision.
-
-
product
PCB Test And Design-For-Test Services Group
ntellitech has a very experienced consulting and test development organization that is dedicated to provide our customers with high-quality design and test services. Choosing Intellitech Test Services can help you lower the risk of adopting a new Design-for-Test methodology or speed your product to market when you need to deploy a test solution quickly.
-
product
cPCI to PMC Adapter / Carrier
cPCI2PMC
The cPCI2PMC ( cPCI to PMC ) adapter / carrier converter card provides the ability to install a PMC card into a standard cPCI slot. The cPCI2PMC has a PMC card slot mounted to a universal 3U 4HP cPCI card. Suitable for 32/64 with 33/ 66 MHz bus operation. The PMC user IO connector Pn4 is optionally connected to J2 for rear panel IO.
-
product
NI-6585B , 200 MHz, 32 LVDS-Channel Digital I/O Adapter Module for FlexRIO
784060-01
200 MHz, 32 LVDS-Channel Digital I/O Adapter Module for FlexRIO—The NI-6585B is a digital I/O adapter module that, when combined with a PXI FPGA Module for FlexRIO, creates a digital instrument for interfacing with 32 low-voltage differential signaling (LVDS) digital pins. A digital I/O adapter module for FlexRIO can be used to do real-time interfacing of standard protocols and implement customized protocols. The NI-6585 can operate at up to 200 MHz clock rates and includes support for common LVDS voltages.
-
-
product
2.92mm to ProBus Probe Adapter
L2.92A-PBUS
The Teledyne LeCroy LabMaster 10 Zi oscilloscope utilizes precision 2.92mm input connectors to achieve up to 36GHz of input bandwidth. But some applications may require the use of lower-bandwidth probes for performance and cost reasons.The L2.92A-PBUS adapter converts the 2.92mm interface to a ProBus interface. This brings the benefits of a wider selection of probes to the LabMaster 10 Zi from high-impedance ZS active probes to the high-bandwidth WaveLink differential probing system. Full probe power and control is provided through a built-in LEMO interface.
-
product
Tool, Press Kit, i2 PCB Headers
910121199
Tool, Press Kit, i2 PCB HeadersAids in pressing fit pins into the header.
-
-
product
NI FlexRIO Adapter Modules
High bandwidth and high resolution AWGs help you to generate with confidence complex signals like digital modulations and RF stimuli for functional and performance tests.
-
product
Pull-Thru Adapters
VPC offers a selection of pull-thru adapters to meet PXI connection needs. Pull-thru adapters consolidate wiring for wired connections and provide a seamless connection to the card for PCB needs.
