-
Product
Gas & Flame Detection System
Syntel
-
Teledyne Gas & Flame Detection
Syntel is an addressable loop system suitable for use in zone 1 and 2 hazardous areas. The complete addressable loo is fault tolerant operating normally with a short or open circuit. Syntel does not have a CPU, so there is no common failure point. It includes a standard OPC interface and can also be supplied by Modbus allowing easy integration with third party systems.Syntel stores alarm and calibration information in distributed non-volatile memory, hence there is no reliance on a centralized system.Syntel is ideal for installations where there is the possibility for future expansion. The system architecture allows very low cost expansion as cable runs to a central location are not needed.
-
Product
OptiStroke™ Needle Stroke Detection System
-
The patented OptiStroke system reduces product waste and confirms hot melt adhesive dispensing performance by verifying valve actuation and fatigue. Ideal for applications where product-yield loss is critical, the system is compatible with Nordson Universal™ modules, Speed-Coat™ modules and Harmony modules.
-
Product
Multi-spectrum IR Flame Detector
FL4000H
-
The FL4000H is an advanced multi-spectrum infrared (MSIR) flame detector that provides superior false alarm immunity with the widest field of view.
-
Product
Needle Microprobe
MT-23/8HT
-
Fast-response 23 gauge needle probe, (needle length is 8 cm) for instant readings in tissue, semisolids, liquids. Also for very small specimens, powders and materials. Needle tip is sealed to ensure only stainless steel contacts specimen. Max. temp. 200°C. 5 ft. lead. Smallest microprobes give fastest reading. Short probes are easier to insert and last longer. Type #'s indicate needle gauge and needle length in cm.
-
Product
Medical Needle Tubing Toughness Tester RX-01
-
The Medical Needle Tubing Toughness Tester is suitable for measuring the toughness of stainless-steel needle tubing, such as injection needles, prefilled syringe needles, and IV (infusion) needles.Product Features Supports testing of various needle wall specifications: normal wall, thin wall, and ultra-thin wall. 7-inch color touchscreen with graphical user interface (GUI) Users can freely select the bending angle and number of test cycles. This instrument features automatic data storage and retains memory even after power-off. This instrument is equipped with multiple safety features to prevent accidents caused by improper operation during testing, including an emergency stop button and overload protection. Equipped with a micro-printer and automatically prints test results upon completion Standard USB interface for convenient data transfer This instrument features multi-level user permissions, compliant with GMP standards. ISP online control and upgrade capabilities enable remote modification of test functions as needed.Test PrincipleSecure one end of the needle stainless-steel tubing and apply a force over a specified span. First, bend it in one direction, then bend it to a specified angle in the opposite direction, and repeat this bending cycle a specified number of times.Test StandardsThis test instrument conforms to many national and international standards:ISO 9626:2016 - Stainless steel needle tubing for the manufacture of medical devicesGB 15811-2025 - Sterile hypodermic needles for single useGB/T 18457-2024 - Stainless steel needle tubing for the manufacture of medical devices
-
Product
2.5mm Test Rod Test Probe Needle
CX-4C
-
Shenzhen Chuangxin Instruments Co., Ltd.
2.5mm test rod test probe needle Used to verify the protection of persons against access to hazardous parts.
-
Product
Needle Microprobe
MT-23/3HT
-
Fast-response 23 gauge needle probe, (needle length is 3 cm) for instant readings in tissue, semisolids, liquids. Also for very small specimens, powders and materials. Needle tip is sealed to ensure only stainless steel contacts specimen. Max. temp. 200°C. 5 ft. lead. Smallest microprobes give fastest reading. Short probes are easier to insert and last longer. Type #'s indicate needle gauge and needle length in cm.
-
Product
Palladium Alloy & Beryllium-Copper Probe Needles
-
Advanced Probing Systems, Inc.
APS has been providing high precision, high volume Tungsten Electrosurgical Needles for over 20 years in Colorado where the product was invented. Our unique Chemical machining process can produce polished electrosurgical needles for diameters from .177mm to .711mm. Overall lengths produced from 25.4mm to 38mm. Tip sizes range from .001mm to .115mm.
-
Product
Curved Needle Test Systems
-
Instron’s Curved Needle Testing System is designed for evaluating surgical and wound closure needles through two specialized testing methods: curved needle puncture testing (per ASTM F3014) and cantilever bend testing. These fixtures assess key performance attributes such as sharpness, coating integrity, and flexural strength. Compact and efficient, the tabletop system conserves bench space while delivering robust functionality. Powered by Bluehill® Universal software, it offers comprehensive control over test execution, data collection, and reporting, along with access to a wide range of built-in calculations.
-
Product
HVFAA Horizontal Vertical FAA Flame Chamber
-
Atlas Material Testing Solutions
The Atlas HVFAA Horizontal Vertical Flame Chamber provides the most accurate means for determining the flammability of aircraft cabin and cargo compartment materials, liners and waste stowage compartment materials, and electric wire. The large volume chamber prevents oxygen depletion during tests. Three digital timers with remote control make specimen event timing precise and convenient. To ensure accurate and repeatable tests, an optional burner flame temperature verification kit is available. The HVFAA is the optimal instrument for conducting repeatable FAA flammability tests and is used in the FAA’s training facility.
-
Product
Needle Hydrophone
HNP-series
-
The HNP needle hydrophone is the de facto standard for doppler mode measurements offering a flat response and wide directivity.
-
Product
Integral Intelligent Flame Detector
FS-100
-
FS-100 utilizes SMT technology which integrates a photoelectric sensor, a microprocessor, and a Human-Computer Interface (HCI) and an output interface together, sending out various outputs including an ON/OFF flame signal, a fault signal, a 4-20mA signal, and an RS-485 output (meets the MODBUS standard) via the quick connector.
-
Product
Multi-spectrum Infrared Flame Detector
975MR
-
The Rosemount 975MR multi-spectrum infrared flame detector is based on accurately analyzing the multi-spectral signals by utilizing three separate IR sensors. The 975MR detects fuel and gas fires at long distances. For example, this product will detect a 1 ft2 (0.1m2) gasoline pan fire at 215 ft (65 m) in less than 5 seconds. The 975MR also provides the highest immunity to false alarms and enhanced overall coverage range.
-
Product
Gas and Flame Detection System
Zero Two
-
Modular system offering the widest range of control cards for use in an integrated fire and/or gas detection system. The Zero Two Series system can monitor any combination of the following: combustible gas, H2S, toxic gas, ultrasonic, oxygen deficiency and flame detection.
-
Product
Needle Pressure Gauge
102
-
The Elcometer 102 Needle Pressure Gauge is designed to measure air pressure up to 20bar (300psi) in blast and air hoses. Pressure drop is responsible for decreased production rates, increased abrasive consumption and reduced anchor profile in abrasive blasting systems.
-
Product
Needle Microprobe
MT-29/2HT
-
Fast-response 29 gauge needle probe, (needle length is 2cm) for instant readings in tissue, semisolids, liquids. Also for very small specimens, powders and materials. Needle tip is sealed to ensure only stainless steel contacts specimen. Max. temp. 200°C. 5 ft. lead. Smallest microprobes give fastest reading. Short probes are easier to insert and last longer. Type #'s indicate needle gauge and needle length in cm.
-
Product
Integral Explosive-proof Intelligent Flame Detector
FSE-100
-
FSE-100 Explosion-proof Flame Detector is used to collect the flame signal which is amplified and processed to determine the presence or absence of flame. FS-100 Flame Detector provides the flame output in real-time – the basis of determining the presence or absence of flame.
-
Product
Needle Microprobe
MT-26/6HT
-
Fast-response 26 gauge needle probe, (needle length is 6 cm) for instant readings in tissue, semisolids, liquids. Also for very small specimens, powders and materials. Needle tip is sealed to ensure only stainless steel contacts specimen. Max. temp. 200°C. 5 ft. lead. Smallest microprobes give fastest reading. Short probes are easier to insert and last longer. Type #'s indicate needle gauge and needle length in cm.
-
Product
Wire Probe Needles Materials & Pin Diameters
-
Advanced Probing Systems, Inc.
Tungsten pins and tungsten-rhenium pins can be provided with either nickel plating or silver plating. Beryllium-copper pins are supplied with a silver plating coating.
-
Product
UV/IR Flame Detector
FL500
-
The FL500 UV/IR Flame Detector monitors for radiation emitted by a flame in both the ultraviolet (UV) and infrared (IR) spectral ranges. This UV/IR combination provides a fast response time and increased false alarm immunity against sources of radiation for reliable protection.
-
Product
Needle Sensors
-
Electronic Development Labs, Inc.
EDL’s Needle Sensors are truly impressive, showcasing lightning-fast response times that deliver accurate temperature readings in as fast as just one-quarter of a second.
-
Product
Field thermal needle system for thermal resistivity / conductivity measurement
FTN01
-
Hukseflux Thermal Sensors B.V.
The FTN01 Field Thermal Needle System allows performing fast, on-site measurements of the thermal resistivity or conductivity of soils, in particular around the typical depth of burial of high voltage cables. FTN01 is designed with a focus on robustness and saving time, while still offering sufficient accuracy for typical field measurements. The sensor is a Non-Steady-State Probe (NSSP), TP09, which is mounted at the tip of the Lance LN01. The system is operated using a hand-held Control and Readout Unit CRU01.
-
-
Product
Manual Test Adapter With Rigid Needles
-
Frequently, manual test adapters are required for the functional and IC test. In order to contact the test subject, spring contact probes are often installed in the adapter, but the pitch of the spring contact probes is approx. 1.27 mm and thus too great for certain applications.
-
Product
Hand Held Needle Detector
UI-G60
-
Hand held needle detector, using the principle of magnetic field, can accurately detect the specific location of ferromagnetic metal impurities such as broken needles, which is very suitable for the inspection of thin and small items. It is also suitable for the detection of large needle detectors. It can accurately find the position of steel needles or ferromagnetic metals in a small range with this hand-held needle detector, avoiding the damage of metal impurities to consumers and manufacturers, and improving the quality of enterprise products.
-
Product
Cross Needle Meter. 1.8 - 60/144/440
MFJ-864
-
This new MFJ Cross Needle SWR/Wattmeter covers HF thru VHF 1.8 - 60MHz, 144 MHz and 440 Mhz bands. It features separate HF and VHF / UHF directional couplers, each with its own SO-239 connectors. This lets you connect your HF and VHF/UHF transceivers at the same time.
-
Product
Flame & Other Plastics Testing
-
Educated Design & Development, Inc.
Plastics are tested to determine their flammability burning characteristics (Flame rating), their ignition potential due to thermal and electrical sources, their resistance to electrical tracking, and other electrical characteristics. The specific test required on a plastic depends on the type of component or end-use product, as well as the environment in which the plastic is used. This test equipment meets most UL, CSA, IEC, EN and other international safety standards.
-
Product
HVR-LS Horizontal Vertical Flame Tester
HVR-LS/HVR-LSS
-
This equipment meets the requirements of ANSI/UL94, IEC60950-1, IEC695-2-2 and GB Standard. It is used to test the appliances and plastic materials parts of electrical equipment for the horizontal, vertical flammability test. The product tank shell is irony spray, and configured a transparent viewing window, the digital meter shows the burning time, afterflame time, afterglow time, this device has beautiful appearance, is easy to use and has reliable performance.
-
Product
Fixed Flame Detectors
-
Teledyne Gas & Flame Detection
Would you like to source high-performance flame detectors? Teledyne Gas and Flame Detection offers detection solutions that precisely meet the needs of the most demanding professionals.
-
Product
Needle Valves
-
Needle valves are designed for laboratory and industrial applications for regulating corrosive gases and liquids or for high purity service. They can also be used as bubble tight shut-off valves.
