Product

Power Interface Board 6U, 1 PSU connector with AC pins

106PIBM601-9001R

-

ELMA Electronic, Inc.

106PIBM601-9001R - ELMA Electronic, Inc.

The PIB 6U 1 slot has one power connector P47 with AC pins and connects to the backplane via power bugs with 6/32 screws. It is used to facilitate pluggable power supplies, headers, and utility connectors.

Product

Ethernet Digital Interface OEM Board

8063

-

ICS Electronics

8063 - ICS Electronics

* Same Digital IO lines as standard 8063. * Same data transfer capabilities as standard 8063 * Digital I/O uses high-density DC-62 connector.* Power connections via 2 screw terminal strip or solder pads.* User configured IDN message and webserver pages makes board respond as part of your system.* Use an ICS Wiring Kit to extend the Ethernet signal to a rear panel RJ45 jack.* Runs on 9 to 32 Vdc power.

Product

Universal Compression Tester for Gasoline Engines

34000

-

S & G Tool Aid Corp

34000 - S & G Tool Aid Corp

Test compression on all domestic and foreign cars and most trucks. Adapters fit vehicles with 14mm and 18mm plugs including long reach and 5/8" hex plugs. Flex hose eliminates need to remove auxiliary equipment such as power brakes and steering, air conditioning and manifold. Screw in adapters guarantee accuracy over push-in type testers. Quick side release valve permits retest without removal of adapters. Gage ranges 0-300 PSI and 0-21 BAR. Supplied in storage pouch.

Product

Dual MAX31865 PT-100 RTD to Digital Breakout

SEN-30202-PT100

-

Playing With Fusion Inc

SEN-30202-PT100 - Playing With Fusion Inc

Dual channel breakout board for the MAX31865 RTD-to-Digital converter from Maxim. Two breakout hardware configurations are available standard, designed to interface with either the PT100 or PT1000 platinum RTDs. For non-standard applications, including thermistors, custom hardware configurations can be accommodated. Contact Technical Support for more information. RTD devices may be wired in 2, 3 or 4-wire configurations using the 4-pin screw terminal input. The MAX31865 breakout is interfaced via 3 or 4-wire SPI with a data-ready output for specific operating modes. An LDO and a high-speed level shifter are included to allow interfacing with microcontroller devices between 3.0V and 5V (all Arduinos, Raspberry PI, etc) without sacrificing device performance.

Product

Digital Input/Output Expander (Open-Collector Outputs)

ENVIROMUX-DI16DO16

-

Network Technologies Inc

ENVIROMUX-DI16DO16 - Network Technologies Inc

Adds 16 digital inputs and 16 digital open-collector outputs to the ENVIROMUX-2D/5D/16D. Interfaces with the ENVIROMUX-2D/5D/16D via the RJ45 Sensor Port. Digital inputs: 16 screw terminal pairs for connecting dry contact devices; One screw terminal pair for tachometer; 0 to 255 Hz. Accepts 26 to 16AWG wire. Potential free. Voltage range: 0 to +36VDC. Over-voltage surge protected. Digital outputs: 16 screw terminal pairs for open-collector outputs. Accepts 26 to 16AWG wire. Rated sink current: 500 mA per output. +5VDC, 22kΩ pull-ups. Voltage range: 0 to +24VDC. Over-voltage surge protected. Supports CAT5/5e/6 cable up to 500 ft. (152.4 m). Powered by ENVIROMUX-2D/5D/16D. Compatible with ENVIROMUX-2D/5D/16D. Dimensions WxDxH: 6.49x3.10x1.08 in (165x79x27 mm). Regulatory approvals: RoHS.

Product

Single Channel USB Programmable Band-Pass Filter

USBPBP-S1

-

Alligator Technologies

USBPBP-S1 - Alligator Technologies

The USBPBP-S1 stand alone USB controllable module provides a single channel of high and low-pass filtering and high-quality instrumentation amplifier for front-end signal conditioning compatible with all popular A/D converter devices. The USBPBP-S1 is powered with 9 to 12VDC so it can be connected to a battery voltage source or the supplied 115-220VAC adapter may be used for operation with wall power anywhere in the world. When programmed from the USB port, the USBPBP-S1 will remember all of the programmed properties between power cycles. Program once and operate as a stand- alone signal conditioner without having to reprogram for every use. This is perfect for turn-key applications. It's easy to connect the USBPBP-S1 into the data collection system. Input and output signals can be routed through BNC connection or using the detachable screw terminal connectors. Optional SMA type adapters are also available.

Product

Positive Displacement Pumps

-

Flowserve Corporation

Flowserve Corporation

Flowserve positive displacement pumps comply either with ASME or API standards. They cover screw and reciprocating pumps in different configurations that guarantee reliable and efficient pumping processes. Numerous sizes, hydraulics and material combinations are particularly well suited for use in applications where uncompromising reliability and efficiency over a wide flow range are key.

Product

Pressure Comparator (System D)

P Series

-

AMETEK Sensors, Test & Calibration

P Series - AMETEK Sensors, Test & Calibration

The P-Series (System D) comparators are hydraulic screw pumps designed for easy, controlled, high pressure generation. Each comparator includes a 4 connection manifold, which can be used for the reference indicator, the device under test, a fine adjust, an isolation valve, or a fluid reservoir. The adjustable reference pressure port lets you set your reference gauge at the best viewing angle. Three models are available for hydraulic oil, water, or both.

Product

IEC60884 Fig22 Plug Socket Covers Pendulum Impact Test Apparatus

CX-BC22

-

Shenzhen Chuangxin Instruments Co., Ltd.

CX-BC22 - Shenzhen Chuangxin Instruments Co., Ltd.

IEC60884 fig22 plug socket covers pendulum impact test apparatusMeet the standard: IEC884-1 Figure 22-26,, IEC60068-2-75Uses: Suitable for household and similar plugs and sockets, wall mounted mounting boxes, screw glands, covers, switches and other electrical accessories for mechanical strength test

Product

SparkFun Qwiic Quad Relay

-

SparkFun Electronics

SparkFun Electronics

The SparkFun Qwiic Quad Relay is a unique power accessory board that has been designed for switching not one but four high powered devices from your Arduino or another low powered microcontroller using I2C. Taking a look at the board, the Quad Relay has four individual relays rated up to 5 Amps per channel at 250VAC or 30VDC. Each channel also has its own uniquely colored LED, silk for easy identification, and screw terminals for optional connection. Utilizing our handy Qwiic system, no soldering is required to connect it to the rest of your system!

Product

Connector Blocks

-

VI Control Systems Ltd.

VI Control Systems Ltd.

VI Control Systems has designed several connector blocks for mating ribbon cables to screw terminals.  Our design goal was to make the connector blocks small and inexpensive.  

Product

Fence Vibration Sensor

ENVIROMUX-FENCE1

-

Network Technologies Inc

ENVIROMUX-FENCE1 - Network Technologies Inc

Detects when individuals climb over or cut through chain link or wire mesh fences. Advanced built-in signal processor prevents false alarms. Four sensitivity settings to tune each sensor to a particular fence section and intrusion type. Two open-collector outputs – alarm and power failure. UV resistant case and epoxy sealed electronics provides maximum resistance to harsh environments. Rated NEMA 4X and UL94 5V. Use individually or chain units with each ranging from 40 to 60 feet away. Includes mounting brackets for installing the sensor to fence fabric. Screw terminals. Operating temperature: -4 to 131°F (-20 to 55°C). Operating voltage: 9-15V DC.

Product

- RS-422/485 DIN Rail Mounted Lightning/Surge Protector

Model 8022NX

-

Telebyte, Inc.

Model 8022NX - Telebyte, Inc.

FEATURES: Fast Response; Automatic Recovery; Up To 20 MBPS Data Rate; DIN Rail Mounted; Full Duplex; Triple Stage Protection. The Model 8022NX is a DIN Rail mounted surge suppressor for 4-wire RS-422 or RS-485 circuits used to protect factory data networks, or, any network that wants to avail itself of the DIN Rail packaging concept. The Model 8022NX provides common-mode (line to ground) surge protection and differential mode (line to line) protection for balanced networks. All the inputs, outputs and ground connections are via screw terminals located on the top surface of the device.

Product

32-CH Discrete Output Modules with U Profile

HSL-DO32-UD

-

ADLINK Technology Inc.

HSL-DO32-UD - ADLINK Technology Inc.

*UD type is suitable for screw type wiring. Each wire to sensors or actuators can be fixed by the screw terminal*RJ-45 phone jack for easy installation*Compact and single board design to meet space limitation and cost-effective requirement*Support 32 DO channels*Transmission speed: 3/6/12 Mbps

Product

Electric Linear Actuators

MaxJac

-

Thomson

MaxJac - Thomson

The MaxJac actuator features a smooth high response ball screw and gear motor and utilizes a proprietary guidance bushing to provide precision smooth linear actuation. Standard equipment includes a 12 volt motor with potentiometer feedback. It is ideal for throttle control, solenoid actuation, and valve actuation in such applications as construction equipment, motor vehicles, marine, and blood infusion pumps.