Product

Probe Holders

Model P7

-

Probing Solutions, Inc.

Model P7 - Probing Solutions, Inc.

Made from 300 series stainless steel, the P7 probe holders accept all model 407 replaceable probe tips, and are secured with a set screw. When used with the P7 Tool Holder Adapter Arm; “Z” position adjustments are easy, and can accommodate a variety fixtures and probe card holders. Designed for both high temperature (-65 to 300°C) and high electrical isolation measurements.

Product

96-Pin 1.27mm Pitch Male Breakout DIN Rail

40-967-096-M

-

Pickering Interfaces Inc.

40-967-096-M - Pickering Interfaces Inc.

Connector blocks provide a convenient method of termination without the use of custom cabling. However, a higher resistance path, lower capacity ratings and lower voltage ratings are typical. This termination option is capable of accepting heavy duty connection wires and uses rising clamp screw terminals to minimize the danger of copper strand damage. Users should care take to protect the termination and provide a suitable method of restraining the cables.

Product

Torque Tester

WDISR-RL series

-

Sugisaki Meter Co., Ltd.

WDISR-RL series - Sugisaki Meter Co., Ltd.

Separate type digital torque driver. The detector is compact and lightweight, for the control of small torque . Interlocking with a personal computer or PLC, the torque measurement can be managed at a higher level. Various screw tightening tests, final tightening checks, tightening data storage, etc.

Product

Electrochemical Cell Accessories

ECA-1

-

PotentioLab

ECA-1 - PotentioLab

Replacement accessories for electrochemical cells, including electrode sealing screws, silicone gaskets, fixing rings, flange clamps, gas tubing, and related components. Compatible with a wide range of laboratory electrochemical systems.

Product

MAX31855 K-Type Thermocouple Sensor Breakout

SEN-30001-KDP

-

Playing With Fusion Inc

SEN-30001-KDP - Playing With Fusion Inc

Breakout board for the MAX31855K digital thermocouple interface IC. Measured temperature range is -270C-1372C with known thermal characteristics and output resolution of 0.25C. This sensor supports a larger operating range (specifically in the negative range) than its predecessors, the MAX6674 and MAX6675, though it is not pin-pin compatible. This board is interfaced with a 0.1" 1x5 pin header and four mounting holes for standoffs and 4-40 screws. It does not contain a mini thermocouple connector.

Product

PCI Daughter Boards

DN-37

-

ICP DAS USA, Inc.

DN-37 - ICP DAS USA, Inc.

DN-37 is a Screw Terminal Board for PC Based I/O Boards with or without din rail mounts. It is an I/O Connector Block with a 37-Pin I/O Connector and 37-pin CA-3710 cable.

Product

DL Linear Actuators

-

Del-Tron Precision, Inc.

Del-Tron Precision, Inc.

Del-Tron's DL series linear lead screw actuators and ball screw actuators offer the benefits of a space-saving design, fast and simple assembly, long life, and a competitive price. The rigid enclosed aluminum box structure provides a compact envelope that incorporates the linear bearing and drive mechanism. Integrating all components into a single unit that includes the motor adaptor saves assembly time and eliminates the need to source additional parts. DL series linear actuators are offered in travel lengths up to 410 millimeters.

Product

Automated Tuners / Impedance Tuners / Load Pull Tuners

-

Maury Microwave Corporation

Maury Microwave Corporation

MT97x, MT98x and XT98x series automated tuners (also known as automated impedance tuners and automated load pull tuners) are precision instruments that are optimized for a broad class of in-fixture and on-wafer applications, and may be used in any automated or manual application requiring the ability to match the impedance of a microwave circuit element or to establish specific impedances at a terminal interface. The tuner design is based on the slide screw concept using the inherently broadband slab-line transmission structure. Each unit has two non-contacting probes deliver high VSWR with superb accuracy and reliability over a wide frequency range. These probes can be fully retracted leaving a low-loss, well-matched transmission line, which is a significant benefit in power related applications where two-port tuners capable of handling large amounts of power are required. As integral components of Maury Device Characterization Solutions, these PC-based tuners are controlled using Maury's family of Device Characterization Software tools, including MT930 IVCAD, MT993 ATS and the DLL-based measurement automation environment. Maury Microwave automed impedance tuners are ideal for load pull, harmonic load pull, active load pull, hybrid active load pull, noise figure, noise parameters and all automated tuner applications.

Product

Multi-Bay Connector Kit with Sides Installed

HW-56

-

ELMA Electronic, Inc.

HW-56 - ELMA Electronic, Inc.

6 each. Screws, nuts and washers (multi-bay connector kit with sides installed).

Product

Touch Posi-Control System V2

DPC

-

Mountz Inc.

DPC - Mountz Inc.

The position control torque arm system helps manufacturers detect and eliminate costly screw-fastening errors during the assembly process. This position control system is designed to reduce the risk of improperly fastened screws, ensuring that every screw is in the correctly tightened in the correct sequence. A good tightening sequence ensures that an even preload distribution is achieved in the joint. Using a position control system is like putting the eyes and ears of a quality control manager where they are needed most - right on the assembly area.

Product

Accessories

-

Advantech Co. Ltd.

Advantech Co. Ltd.

A DIN-rail terminal board is a wiring board with dedicated connectors for the motors of Panasonic Minas A series, Mitsubishi MR-J2S series and Yaskawa Sigma 2 series. This terminal board can save time and effort of wiring. Each ADAM-3900 series wiring board features DIN-rail mounting terminals and consists of universal screw terminal modules designed for field signal wiring in industrial applications.

Product

Serial RS-232 Expansion Connector Accessory for USBHub3c

-

Acroname, Inc

Acroname, Inc

Used for connecting a serial RS-232 interface to the control the USBHub3c through the expansion interface connector. Screw terminals are provided for the RS-232 interface. While this board provides for wiring connections, a host machine external to the USBHub3c is required for this control interface.

Product

PCI Daughter Boards

DB-8125

-

ICP DAS USA, Inc.

DB-8125 - ICP DAS USA, Inc.

ICP DAS USA offers economical solutions to meet your industrial needs. DB-8125 is part of our wide selection of Screw Terminal Boards for PC Based I/O.

Product

Data Logging Kit

ThermoVault

-

MadgeTech, Inc

ThermoVault - MadgeTech, Inc

Oven Temperature Profiling kit. Comes with TC101A Thermocouple based Temperature Data Logger with screw terminal, Thermally insulated enclosure, and Type K thermocouple probe.

Product

Pneumatically Powered Bed of Nails Testers

Automator Pneumatic Family

-

Test Electronics

Automator Pneumatic Family - Test Electronics

Designed to provide factory assembly line conveyor based pneumatically actuated full test automation. Interchangeable pneumatics and manual lever options provide operation as a fully automated tester or as a manual bench top tester. These functional interchangeable options allow this fixture to grow with you as your production volumes increase. Test plate changeover is a quick 2 minute job. 4 thumbscrews to change the bottom plate and 4 SHC screws to change the top plate. The top plate drops down and slides out with the connector assembly. The bottom plate lifts up and out. The new plates slide back in. All rear panel connectors are mounted to the aluminum bracket on the top plate. This whole top plate assembly slides out together eliminating wiring hassles. Double sided access plate sets use transfer pins to get the signals from the bottom plate up to the top plate.

Product

160 Pin DIN Connector & Cable Accessories

-

Pickering Interfaces Inc.

Pickering Interfaces Inc.

The 160 Pin DIN connector is used on switching products to provide a high density 2A connector solution. If you would like to develop your own cabling solutions, we offer mating connectors and connector hoods that allow you to create either your own cable based solutions, or a PCB header solution. Connector Blocks directly terminate the module connector and convert the connection to arrays of screw terminal blocks, or you can select to use a remote DIN rail mounted breakout to terminate the cables at the end of a cable assembly. You can also try our Cable Design Tool to graphically design a customized cable assembly.

Product

Electric Linear Actuators

MaxJac

-

Thomson

MaxJac - Thomson

The MaxJac actuator features a smooth high response ball screw and gear motor and utilizes a proprietary guidance bushing to provide precision smooth linear actuation. Standard equipment includes a 12 volt motor with potentiometer feedback. It is ideal for throttle control, solenoid actuation, and valve actuation in such applications as construction equipment, motor vehicles, marine, and blood infusion pumps.