-
Product
Shaft Alignment
NXA Pro
-
30 years of innovation continue with the introduction of the NXA Pro.
-
Product
Shaft Speed Sensors
-
Electro-Sensors offers many shaft speed sensors for virtually any environment. Our Hall-Effect and Magnetoresistive Sensors sense magnetic targets and work with our magnetic pulsers (Discs, Wraps, and Wheels). Our proximity sensors sense ferrous metal targets, including bolt-heads, screws, gearteeth and keyslots. Our speed sensors monitor shaft speed of equipment and output data as PNP, NPN, or 4-20 mA signals. The sensor data can be used by facilities to monitor machinery and safeguard equipment. Monitoring shaft speed is a fundamental aspect of hazard monitoring and should be utilized by any facility with rotating shafts.
-
Product
Shaft Speed Sensors - Magnetoresistive
1102 / 932 / 933 XP
-
Features• Square-wave pulse frequency output, NPN open-collector• Zero speed operation with no signal loss• 5-24 VDC powered• 1/2" NPT conduit port (933 XP)• Non-contact, large gap distance sensing• Simple to install and set up• Works with Electro-Sensors magnetic pulser discs / wraps• 1102 – non-threaded stainless steel
-
Product
Slide Gate & Shaft Position
-
All six Shaft Angle Position Feedback Monitors in the SG1000 Series utilize absolute rotary encoders to provide independent and accurate feedback of a slide gate's or a valve's position to an external device such as a PLC or optional PM500 Process Meter Display Unit. Models are housed in a rugged, Explosion-Proof/Dust-Ignition Proof cast aluminum enclosure that is dirt, dust, grease-proof, and water resistant. In the case of a power failure, all SG1000s are designed to retain accurate gate position.
-
Product
Rotary Shaft to Shaft Torque Sensor
-
Futek Advanced Sensor Technology, Inc.
The Rotary Shaft to Shaft Torque Sensor category has Torque Sensors which are used in slip ring and non contact rotary torque measurements. The most common utilization for these models is for inline/reaction applications, where measurements can be made in both clockwise and counterclockwise directions. The Rotary Shaft to Shaft Torque Sensors are CE certified and utilize a bonded metal foil strain gauge. As with most FUTEK products, we will gladly work with you to customize or modify our Torque Sensors to meet your precise needs.
-
-
Product
Shaft Alignment
EVO
-
The evolution of laser shaft alignment towards simplicity and confidence continues with the EVO.
-
-
Product
Shaft Measuring Gage with Dual Glass Linear Encoder
1100GX
-
The economical gaging system of the Model 1100-GX handles a wide variety of part lengths and configurations, resulting in fast, highly accurate measurements of cylindrical engine components. Whether it is needed for use in a lab setting or out on the shop floor, this rugged gage is adaptable to a wide variety of work environments. This versatile gage employs the latest technology in motion controls, signal processing and linear grating technology.
-
Product
Radius, Straight Shaft Bullet Nose, Standard 0.61 (17.00) - 2.80 (79.00) General Purpose Probe
HPA-0J
-
Current Rating (Amps): 3Average Probe Resistance (mOhm): 35Test Center (mil): 50Test Center (mm): 1.27Full Travel (mil): 100Full Travel (mm): 2.54Recommended Travel (mil): 67Recommended Travel (mm): 1.70Mechanical Life (no of cyles): 1,000,000Overall Length (mil): 635Overall Length (mm): 16.13
-
Product
Rotating Dual Shaft Torque Sensors
RST SERIES
-
The RST- Series is our low range rotating torque sensors that are available in eleven full scale ranges of 10 through 30K inch pounds. The sensing element incorporates bonded foil strain gages of the highest quality along with coined silver slip ring and silver brushes for data transmission. The WR2, Flexural Natural Frequency, and Torsional Stiffness values as stated in the Dynamic Characteristics box below, are approximate and the tabulated data pertains to the torque pickup only, and does not include the effects of couplings or other rotating masses that would be part of a dynamic system.
-
Product
Shaft Speed Switches
-
A speed switch senses rotating shaft speed, comparing it to one or more settable over/under/zero speed alarm trip-points. A shaft speed sensor detects magnets embedded in a shaft-mounted pulser wrap/disc. As the shaft rotates, the passing magnets are detected across an air-gap as pulses with frequency proportional to shaft RPM. When a conveyor belt or bucket elevator begins to slip the pulse frequency (shaft RPM) crosses to the alarm side of a trip-point threshold, a corresponding relay de-energizes, providing shutdown or alarm.
-
Product
Laser Shaft Allignment Tools
-
PRÜFTECHNIK Condition Monitoring GmbH
A laser alignment system is the most efficient way to align rotating machinery shafts. Using an adaptive alignment system instead of conventional alignment tools saves you time and money, increases machine availability, prolongs service life and maintenance intervals, and lowers power consumption. Alignment tools from PRUFTECHNIK adapt to virtually any asset, situation, or user skill level.
-
Product
EEXI Shaft Power System (SHaPoLi)
-
Datum Electronics Ltd has developed a shaft power limitation (SHaPoLi) EEXI Shaft Power System, providing the necessary features and functionality to comply with the MARPOL Annex VI, MEPC.335(76) EEXI regulations.Our system uses a Shaft Power Acquisition Module to constantly display, monitor and record propulsion shaft power to ensure compliance with the EEDI requirements relating to CO2 emissions for ships over 400 gross tonnage.
-
Product
Shaft Power Measurement Kits
-
Shaft Power Measurement Kits are available in two formats, the standard and the compact kit. The compact kit is ideal for single day trials, while the standard one is used for long duration trials of between 30-60 days.
-
Product
Radius, Straight Shaft Bullet Nose, Alternate 0.78 (22.00) - 3.70 (105.00) General Purpose Probe
HPA-0J-1
-
Current Rating (Amps): 3Average Probe Resistance (mOhm): 35Test Center (mil): 50Test Center (mm): 1.27Full Travel (mil): 100Full Travel (mm): 2.54Recommended Travel (mil): 67Recommended Travel (mm): 1.70Mechanical Life (no of cyles): 1,000,000Overall Length (mil): 635Overall Length (mm): 16.13
-
Product
Cup, Straight Shaft Concave, Standard 0.61 (17.00) - 2.80 (79.00) General Purpose Probe
HPA-0G21
-
Current Rating (Amps): 3Average Probe Resistance (mOhm): 35Test Center (mil): 50Test Center (mm): 1.27Full Travel (mil): 100Full Travel (mm): 2.54Recommended Travel (mil): 67Recommended Travel (mm): 1.70Mechanical Life (no of cyles): 1,000,000Overall Length (mil): 635Overall Length (mm): 16.13
-
-
-
Product
Miniature Absolute Magnetic Shaft Encoder
MA3
-
The MA3 is a miniature rotary absolute shaft encoder that reports the shaft position over 360 with no stops or gaps. The MA3 is available with an analog or a pulse width modulated (PWM) digital output.
-
Product
Shaft Power Measurement Solutions
-
Our marine shaft power meter systems measure shaft torque, power, propulsion, rpm and thrust (if required), to ensure optimum performance is maintained throughout the lifecycle of a vessel. Using highly accurate & reliable strain gauge technology, combined with cutting-edge electronics, our system has an accuracy of 0.1%. It can be installed and commissioned within 1-2 days on a variety of shafts including intermediate shafts, thrusters, propellers and controllable pitch propellers. Our technology, along with our expertise in dynamic sampling of strain gauges, enable us to unlock a significant amount of information regarding the performance of the engine & propulsion shaft, along with the propeller.
-
Product
Open Optical Encoders
-
An optical encoder is an electromechanical device which produces an electrical signal output proportional to the linear displacement of a linear guide or the angular position of an input shaft.Open encoders are exposed and feature no external integrated enclosure. The advantages of open optical encoders include the effective elimination of backlash, shaft wind-up (torsion) and other mechanical hysteresis errors.A rotary open optical encoder consists of a position measurement readhead and an accurate rotary scale marked either on the periphery of a ring or on the face of a disc.The readhead measures position by optically sensing the regularly-spaced scale markings and outputs this information as an analogue or digital signal.The signal is subsequently converted into a position reading by a digital readout (DRO) or motion controller.
-
Product
Induction Bearing Heater Tools
-
PRÜFTECHNIK Condition Monitoring GmbH
Induction bearing heating tools are the safest and most effective method for mounting bearings onto shafts. Bearing induction heaters ensure even and controlled heating of the bearing and work pieces. Our induction heating tools for small and large bearings are safe and easy to use.
-
Product
Absolute Magnetic Kit Encoder
MAE3
-
The MAE3 is an absolute magnetic kit encoder that provides shaft position information over 360 of rotation with no stops or gaps. This magnetic encoder is designed to easily mount to, and dismount from, an existing shaft to provide digital feedback information. The MAE3 is available with an analog or a pulse width modulated (PWM) digital output.
-
Product
Ultra-Thin Telemetry Collar
-
Advanced Telemetrics International
The Ultra-Thin Telemetry Collar houses all of the electronics needed to provide a precision radio frequency link from sensors mounted on rotating shafts to stationary data acquisition and display instruments.
-
Product
Quadrature Position & Rate Meter
-
Accepts low-level differential or single-ended 5 V logic level quadrature signals from shaft encoders to display scaled position or scaled rate. One, two or four transitions may be counted at a maximum combined rate of 250 kHz and be mathematically scaled to display in engineering units from -999,999 to +999,999. An analog output scaled to the display and relay outputs are optional.
-
-
Product
Tachometers/Torque Meters
-
Tachometers measure rotational or linear speed and come in two styles: contact and non-contact. Contact models come with various rubber/plastic adapters for interfacing the instrument’s shaft with the surface of the spinning or moving surface under test. Non-contact models come with reflective tape that is placed on the surface to become the target of the instrument’s low-power laser.
-
Product
Standard Directional Gyroscopes
4000B-series
-
The 4000B is our standard air-driven directional gyro. As the aircraft turns left or right, gears on the sensing unit and dial shaft translate this rotation into rotation of the instrument’s vertical dial. Left turns produce clockwise dial rotation and right turns produce counter-clockwise rotation. The gyro is controlled by a heading selector knob located on the lower left of the instrument. Pressing and turning the knob first disengages the dial shaft and then resets the dial to a new heading, which results in a new course indication. Releasing the selector knob re-engages the dial shaft. The on-course position of the pointer is always at the top of the azimuth circle (0° on the dial with the aircraft headed north).
-
Product
Laser Trackers
Radian Series
-
The smallest, lightest, most accurate laser measurement tool. API’s compact and rigid UNIBODY tracker design allows for shaft mounted motors, encoders and laser. The UNIBODY shaft mounted laser innovation minimizes Abbe offset errors, while also housing laser source, optics, camera and major head electronics in the center of the tracker body.
