Polarizers
allow light waves of a specific polarization to pass while blocking others.
See Also: Polarization
-
Product
Digital 5KV High Voltage Insulation Tester
Model KM 6305IN
-
Kusam Electrical Industries Limited
• Microprocessor-controlled.• Tests insulation resistance up to 10 TΩ • 4 Insulation test voltages: 500V, 1000V, 2500V, 5000V.• AC / DC Voltmeter.• Short-circuit current up to 5mA• PI (Polarization Index) indication.• DAR (Dielectric Absorption Ratio) indication.• Auto-ranging on all insulation ranges.
-
Product
Current Transformer Tester
CTT
-
The CTT is designed to test the current transformer ratio, Phase shift, Polarity, Excitation, Saturation, Winding resistance and Insulation resistance using the voltage method in compliance with ANSI/IEEE C57.13.1 and IEC 60044-1 standards, where voltage is applied to the secondary X terminals of the current transformer.
-
Product
Phase Domain Induced Polarization/Resistivity Instruments
ULTRA MiniRes
-
*Light weight yet durable*Low power consumption*Lowest cost in the industry*Exploration to greater than 1000 feet**2.5 HertzMEASURES:*Earth resistivity*Induced polarization
-
Product
15-CH Isolated Digital Input Module
ND-6054
Data Acquisition Module
- Channels: 15- Isolation Voltage: 5000 VRMS- Switching Level: with 24 V common power. Low (0): 22 V min.; High (1): 0-22 V- Programmable input polarity
-
Product
Bench/portable Universal Counters With USB Interface 3GHz Or 6GHz
TF900 Series
-
Frequency, period, pulse width, frequency ratio, duty cycle, and event counter modesDC to 3000 or 6000MHz range, 0.001mHz resolutionHigh impedance measurement up to 125 MHzAC or DC coupling, 1M/50Ohm selection, polarity invertSwitchable attenuator, threshold controlNoise filter for low frequency measurementsSelectable measurement time; display hold functionLarge 10 digit display with full range of annunciatorsInternal rechargeable batteries for portable useUSB interface provides full remote control and readback
-
Product
Spot-Focusing Lens Antennas
-
The antenna employs a low loss lens to offer excellent aperture efficiency at 105.96 GHz. The lens antenna is equipped with a standard WR-10 waveguide and UG-387/U-M flange as its input port. It supports linear polarized waveforms.
-
Product
V-FullWaver
-
The V-FullWaver systems were specifically developed for precise full waveform time domain Induced Polarisation, Resistivity and SP measurements. Each system is fully independent; incorporating its own power source, GPS module and digital memory for up to 3 months continuous recording. The V-FullWaver is a dual channel Induced Polarisation, Resistivity and SP receiver. Continually recording at 10ms sample rate provides a full waveform record. It can be synchronized on the GPS PPS signal, allowing an easy process of the signal. Data on the memory can be downloaded directly on a simple USB stick from all the Fullwavers.
-
Product
SMART MEGOHMMETER
MD-1035e
-
The Megabras MD-1035e is a smart, microprocessor-controlled, 1 kV insulation tester. Besides the conventional measurement of insulation resistances up to 1 TΩ, its advanced features allow to automatically measure both the Polarization Index and Dielectric Absorption Index, thus significantly simplifying testing of transformers.
-
Product
OBD-II Breakout Box
PPECB
-
The Power Probe OBD-II Breakout Box is a CAN Bus circuit tester compatible with 12 and 24 Volt systems. The tool connects directly into the Vehicle’s Data Link Connector (DLC) testing for any abnormalities such as shorting and reverse polarity at the pins. If shorting or reverse polarity is present, connecting the PPECB first will prevent harm before connecting a Diagnostic Scan Tool. The Breakout Box provides a live display of present communicating signals without having to use a Digital Multimeter. Additionally, you can quickly test the voltages at all 16 pins.
-
Product
Light Analysis
-
Welcome to Thorlabs; below you will find links to detectors and instrumentation that measure the various properties of light, a subset of our entire line of photonics products. Thorlabs offers an extensive selection of instruments that measure the properties of light. Our versatile power and energy meters can be used with over 25 different sensors in order to make NIST-traceable power and energy measurements. If the convenience of a meter is not desired, our selection of detectors includes basic photodiodes (uncalibrated and calibrated), photodetectors (biased, amplified, and avalanche), CCD and CMOS arrays, position detectors, integrating spheres, and photomultiplier tubes. The Beam Characterization category contains beam profilers (camera and scanning slit), a wavefront sensor, spectrometers, and interferometers, while the Polarimetery link leads to a selection of instruments used to measure and control the polarization of light.
-
Product
Pole Tester
Typ Pot 1
-
To the statement of the polarity (north - south) and the arrangement of magnetic poles (sensor foil).
-
Product
1.0µm PM Fiber Amplifier ( PM YDFA )
HAPM1000
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HAPM1000 is a Polarization Maintaining Fiber Amplifier which worked in 1050~1080nm operating wavelength. Adopt Polarization Maintaining (PM) ytterbium-doped fiber, output optical power range 0.5W~5W, extinction ratio >20dB.
-
Product
Through Hole type DC Current Sensor／for DC Leakage Current Measurements
DCZCT-60NK
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*DC earth fault measurement*DC leakage current measurement*Least affection from the magnetization of core and temperature fluctuation*Convenient ＋24V single polarity power supply
-
Product
4/8-CH 12-Bit 1 MS/s Analog Output Multi-Function PXI modules
PXI-2500 Series
Analog Output Module
ADLINIK PXI-2501 and PXI-2502 are high-speed, high-performance analog output multifunction PXI modules. These devices are able to update up to 8-CH, 12-bit analog outputs imultaneously sustaining 1 MS/s. The reference sources and output polarities are programmable individually per channel. Combine this with the multiplying PXI architecture, ADLINK PXI-2500 series PXI modules can generate complex modulated analog signals. The hardware-based arbitrary waveform generation frees CPU intervention even when all analog outputs are updating at full speed, and the lengths of waveforms are only limited by the system memory. The PXI-2500 series integrate up to 8-CH, 400 kS/s, 14-bit single-ended analog inputs with programmable polarity, 24-CH programmable digital I/O lines, and 2-CH 16-bit general-purpose timer/counters.
-
Product
PoE Voltage Monitor Detect & Verify
PE-400
-
PE-400 is specific to test and verify PSE or Ethernet outlet either a standard/active PoE or a NON-standard/passive PoE to avoid damaging Non-PoE device as well as monitor and display available Voltage simultaneously. It built-in PoE interface controller to trigger on 802.3 af, at and bt switch and verify standard PoE type either 802.3 af or 802.3 at, and power source either End or Mid or both, and power polarity as well as display voltage values. The operational voltage which should be measured when installing a new PoE system or when you troubleshooting an existing system.
-
Product
YDFA Amplifier
-
a high-gain three staged polarization maintaining optical amplifier unit designed for applications requiring high efficiency optical amplification in the 1060 nm regime in both CW and pulse mode operations.
-
Product
Analytical Services
-
IGC: Inverse Gas Chromatography; Understand surface energies, polarities, acid/base properties and nanomorphology on powders and fibers. ToF-SIMS: Time-of-Flight Secondary Ion Mass Spectrometry. Localize your molecules at the first nanos! 2D imaging with resolution up to 200 nm. Highest sensitivity up to 10 ppm. CM: Quarz Crystal Microbalance In-situ observation of thickness and stiffness of any films in liquid environmentSEM: Scanning Electron Microscopy Images say more than words, especially with an artistic eye XPS/ESCA: X-ray Photoelectron Spectroscopy/Electron Spectroscopy for Chemical Analysis.
-
Product
CTEK US 0.8 Battery Charger
56-865
-
US 0.8 is CTEK’s smallest 12 V charger. It offers state of the art technology and is perfect for charging smaller 12 V batteries that can be found in motorcycles, jet skis, ATVs and lawnmowers. It is also suitable for maintenance charging “normal- sized” batteries such as car batteries.The unique display allows the user to follow the entire charging process. The US 0.8 is a compact and fully automatic 6-step charger for 12 V batteries from 1.2–32 Ah and is suitable for maintenance charging up to 100 Ah. The US 0.8 is splash and dust proof, delivers 0.8 A and is designed to protect vehicle electronics. It is non-sparking, reverse polarity protected and shortcircuit proof. The US 0.8 is delivered with 5-year warranty.
-
Product
950~2400MHz DVB-S 4 ways SAT-IF & 1 way CATV CWDM Optical Transmitter & Receiver
HDBS-5000CW
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HDBS-5000CW series combines 4 units SAT-IF optical transmitters and 1 unit CATV optical transmitter, or SAT-IF optical receivers that has CWDM standard wavelength into one housing. The built-in CWDM Multiplexing or De-multiplexing the 5-way optic, and transmit via one single fiber, which can transmit four-way SAT-IF signal of VL, VH, HL HH four polarizations and one-way CATV signal in one satellite with a high quality, flexible to install and convenient to use.
-
Product
Speaker Component Checker
Cab Driver
-
Whirlwind Music Distributors, Inc.
The CAB DRIVER is a test device for checking the operation of the speaker components within enclosures. A pink noise signal source is sent through pushbutton selectors to an assortment of speaker connectors, including Speakon NL8 and NL4, 1/4" TS and banana jacks. Speaker/ Polarity/ Impedance/ Pink Noise Generator
-
Product
Decade Box, Calibrated W/D & U, Capacitance, 5, 100pF to 11111µF, 5 %
72-7265 CAL DU
-
The 72-7265 CAL DU from Tenma is a capacitance decade box. It is ideal for service, prototype and experimental use. This useful tool may be set at any non polarized capacitor value from 100pF to 11,111µF in 100pF increments. The decade accuracy is ±5% capacitors used throughout at <1μF, 1KHz test frequency, ≥1μF, 100Hz test frequency. It has weight of 304g/0.69lb and dimension is 14.7cm × 11.7cm × 5.5cm (5.79" × 4.61" × 2.16"). It is typically used in general applications, troubleshooting, maintenance, education and vocational training, production line testing, radio and TV services, working standards, research design & develop, physics laboratory work.
-
Product
Benchtop Metrology Solution
FilmTek 2000 PAR-SE
-
Scientific Computing International
Our most advanced benchtop metrology solution, engineered to meet the needs of nearly any advanced thin film measurement application, from R&D to production. Combines spectroscopic ellipsometry and DUV multi-angle polarized reflectometry with a wide spectral range to deliver the highest accuracy, precision, and versatility in the industry. Patented parabolic mirror technology allows for a small spot size down to 50µm, ideal for direct measurement of product wafers and patterned films.
-
Product
Polarization Controller and Scrambler - MATRIQ
Controller
The Pol 1000 Series enables high-speed automated polarization control for polarization dependent testing procedures.Rotate or scramble the polarization of your signal with no need for manual adjustment of paddles or tension screws using intuitive software, LabVIEW or comprehensive SCPI commands.
-
Product
8-CH Isolated Digital Input Module
ND-6052
Data Acquisition Module
- Channels: 8 DI. 6 fully independent isolated; 2 isolated with common ground- Isolated Voltage: 5000 VRMS- Programmable input polarity
-
Product
16-CH Digital Input Module
ND-6053
Data Acquisition Module
- Channels: 16 DI- Channels: 16 DI: Logical 0: close to GND; Logical 1: open; Effective distance: 500m- Wet contact: TTL level- Programmable input polarity
-
Product
Dipole Antenna
ZOJ7-20-100-1399
-
Dipole Antenna, Frequency 20~100MHz, Gain-7dBi, VSWR 3.5, Linear Polarization, N Type Female
-
Product
Transient Over-voltages Tester
SUG335
-
The SUG335 is a 1.2/50μs Transient Over-voltages Tester. The polarity interval time can be at least 1s. The standard voltage waveform complies with the IEC 60335, IEC61180, IEC 62052-11: 2003, IEC 61008-1: 1996, IEC 61009-1:1996 and IEC 60947-1: 1995, IEC60060, IEC1036 surge voltage test and has been used for safety testing to determine if the clearance was fulfilled the safety requirement while the transient voltage in the circuit.
-
Product
Metallographic Analyzer
MDS-5000D
-
Wuxi Jinyibo Instrument Technology Co., Ltd.
1) the Integrated T -shaped Mirror Design, PROVIDING Superior Stability 2) Low-position Front Operation, Ergonomic requirements . 3) 6V / 30W Adjustable Halogen LAMP, PROVIDING Ample Bright Lighting System . 4) 3/8 splitting of Tube The trinocular , Observation and photography can be carried out simultaneous 5) Low-position mechanical moving platform to quickly locate the image 6) Professional flat-field metallographic objective lens, providing good resolution and clear image 7) Polarization Detecting partial inserts, related polarized light observation mode 8 )Five-hole rotary disc type color filter, easy to operate and switch 9) Adjustable field of view diaphragm and aperture diaphragm, providing good contrast metallographic analysis software system CCD camera will The optical image from the microscope is converted into a video signal, and the Sample image under the microscope is input into the computer through the image acquisition card / digital camera, and the digital image is processed and measured by the software, and finally the image and the measurement result are printed. Back up images and measurement data. General system:General image processing functions: image acquisition, data backup, depth of field expansion, grain boundary reconstruction, image stitching, image calculation, filtering, Image annotation, image segmentation and processing, accurate printing. Professional analysis system: 1. Rating: based on inspection Standards, more than 200 software functional modules in more than 100 categories.
-
Product
Cable Tracers
-
Shanghai Beha Electronics Co., Ltd.
*Trace wires or cables.*Continuity and polarity testing.*Digital Multimeter
-
Product
Polarizers
-
Achieves high contrast and high transmission for the UV, VIS, NIR, and Mid-IR ranges with a wide acceptance angle of ±20°. The prolate silver nano-particles are embedded inside the glass which results in high durability, wide temperature range, and easy cleaning.
