Filter Results By:
Products
Applications
Manufacturers
PXI Interfaces
-
product
CompactPCI Interface Card
CPCIC-1553/PXI
The CPCIC-1553/PXI Interface Card and AltaAPI Represent the Latest MIL-STD-1553 32-bit FPGA Protocol Engine Technology with Multi-Layer Software. Our Card and Software Packages are Designed for Fast, Portable Integrations. The CPCIC-1553 is the Only Commercial Off the Shelf (COTS) Card that Passes and Executes the SAE AS4111/4112 Protocol Tests.
-
product
PXI Interface Module, AIT MIL-STD 1553
M3406A
Interface to the LRU in avionics test solution Up to four channel MIL-STD-1553 bus interface with full error injection and detection Concurrent Bus Controller, multiple Remote Terminals (31), and Bus Monitor operation capabilities Data capture filtering, 100% bus recording, and physical bus replay Variable output voltage signal and software selectable bus coupling modes 10 high voltage (up to 30 V) programmable DIO lines PXI trigger generation on 1553 bus events
-
product
PXI High Density MUX BRIC, 32-Chan, 10-Pole
40-570-412
This range of High-Density Multiplexer is part of our BRIC family. These MUX's are designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is also possible, without limitation). These multiplexers are ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. They are available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts. All version are supported in a BRIC8 construction that occupies eight PXI 3U mechanical slots, one of which provides the PXI interface and power.
-
product
PXI High Density MUX BRIC, 20-Chan, 40-Pole
40-570-215
This range of High-Density Multiplexer is part of our BRIC family. These MUX's are designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is also possible, without limitation). These multiplexers are ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. They are available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts. All version are supported in a BRIC8 construction that occupies eight PXI 3U mechanical slots, one of which provides the PXI interface and power.
-
product
PXI Express High Speed Optical FPGA Board
HSS-8324
The Conduant HSS-8324 Optical FPGA board provides the user with a hardware platform that is able to sustain full-duplex high-bandwidth transfers through its 8-lane Gen3 PXI Express (PXIe) interface and its 24-lane optical interface. The PXIe interface provides a theoretical maximum throughput of 8GB/s (simultaneous in and out).
-
product
PXI Automotive Ethernet Interface Module
The PXI Automotive Ethernet Interface Module communicates with Automotive Ethernet so that you can use the NI‑XNET driver or standard networking drivers to develop applications that require Automotive Ethernet to test and validate automotive electronic control units (ECUs). It provides up to four independent endpoints or up to two network terminal access points (TAPs). With onboard hardware timestamping and the ability to act as 802.1AS masters or slaves, the PXI Automotive Ethernet Interface Module can synchronize with an external network as well as the rest of a PXI system.
-
product
PXI Prototyping Module, 2-Slot no Connector
40-225A-002
The 40-225A PXI Prototyping Modules are stripped down versions of the 40-220A PXI Breadboard series. These are very basic, low cost prototype modules. They have no PXI interface but do have access to fused power supplies from the PXI backplane.
-
product
PXI Ethernet Interface Module
PXI Ethernet Interface Modules equip PXI systems with high-bandwidth Ethernet-based connectivity with up to 40 Gb/s data rates per port. Featuring compatibility with industry-standard network and automatic cable polarity detection, these modules are ideal for high-performance data transfer and vision applications on the PXI platform. These modules have independent bandwidth to support two GigE Vision cameras with Power over Ethernet (PoE).
-
product
PXI High Density MUX BRIC, 4-Chan, 40-Pole
40-570-211
This range of High-Density Multiplexer is part of our BRIC family. These MUX's are designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is also possible, without limitation). These multiplexers are ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. They are available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts. All version are supported in a BRIC8 construction that occupies eight PXI 3U mechanical slots, one of which provides the PXI interface and power.
-
product
Bus Expanders
PXI Bus Expanders and PXI Interface Cards for both PXI and PXI Express interfaces.
-
product
PXI Express High Speed Optical FPGA Board
HSS-8324-DSP
The Conduant HSS-8324 FPGA board provides a user programmable hardware platform that is able to sustain full-duplex high-bandwidth transfers through its 8-lane Gen3 PXI Express (PXIe) interface and its two 12-lane HSS interfaces while performing complex calculations. The PXIe interface provides a theoretical maximum throughput of 8 GBps (simultaneous in and out) while each HSS port (12 lanes up to 16 Gbps per lane) supports a full duplex transfer at theoretical rates over 190 Gbps.
-
product
SFP+ Cable, 0.5m
784076-0R5
1-Pin, Male SFP+ to 1-Pin, Male SFP+ or 2-Pin, LC/LC Duplex to 2-Pin, LC/LC Duplex SFP Cable - The SFP+ Cable connects to the SFP port on some PXI High-Speed Serial Instruments, PXI Ethernet Interface Modules, Controllers for FlexRIO, and USRP RIO devices. The LC/LC Duplex model … has multimode and single-mode optical fiber options that you can use in tandem with SFP+ optical transceivers. The cable is rated for transmission speeds up to 10.3125 Gbps and is offered in different lengths.
-
product
PXIe-8523, 4-Port, 100/1000BASE-T1 PXI Automotive Ethernet Interface Module
787311-01
PXIe, 4-Port, 100/1000BASE-T1 PXI Automotive Ethernet Interface Module - The PXIe-8523 is a 100/1000BASE-T1 unshielded twisted pair (UTP) PXI Automotive Ethernet Interface Module for developing applications with the NI‑XNET driver. With this hardware, you can develop applications … that require Automotive Ethernet to test and validate automotive electronic control units (ECUs). The PXIe-8523 provides up to four independent endpoints or up to two network terminal access points (TAPs). It features onboard hardware timestamping and can act as up to four separate 802.1AS masters or slaves, so it can synchronize with an external network as well as the rest of a PXI system. The PXIe-8523 also provides LEDs on the front panel to help you monitor the network link and activity.
-
product
PXI Prototyping Module, 1-Slot, 15-Pin D-Type
40-225A-601
The 40-225A PXI Prototyping Modules are stripped down versions of the 40-220A PXI Breadboard series. These are very basic, low cost prototype modules. They have no PXI interface but do have access to fused power supplies from the PXI backplane.
-
product
PXI Prototyping Module, 2-Slot, Dual 20-Pin GMCT
40-225A-812
The 40-225A PXI Prototyping Modules are stripped down versions of the 40-220A PXI Breadboard series. These are very basic, low cost prototype modules. They have no PXI interface but do have access to fused power supplies from the PXI backplane.
-
product
Multi-Channel, Multi-Protocol 1553, ARINC, WMUX Interface for 3U PXIe
Alta Data Technologies’ PXI Express interface modules offer a wide range of MIL-STD-1553, ARINC and WMUX configuration options using Alta’s PMC cards on a single-slot PXI Express 3U carrier. The cards are based on the industry’s most advanced 32-bit FPGA protocol engines, AltaCore™, and by a feature-rich application programming interface, AltaAPI™ (with LabVIEW SDK).
-
product
PXI Prototyping Module, 1-Slot, Dual 20-Pin GMCT
40-225A-811
The 40-225A PXI Prototyping Modules are stripped down versions of the 40-220A PXI Breadboard series. These are very basic, low cost prototype modules. They have no PXI interface but do have access to fused power supplies from the PXI backplane.
-
product
PXI Prototyping Module, 1-Slot, 20-Pin GMCT
40-225A-801
The 40-225A PXI Prototyping Modules are stripped down versions of the 40-220A PXI Breadboard series. These are very basic, low cost prototype modules. They have no PXI interface but do have access to fused power supplies from the PXI backplane.
-
product
PXI High Density MUX BRIC, 4-Chan, 80-Pole
40-570-112
This range of High-Density Multiplexer is part of our BRIC family. These MUX's are designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is also possible, without limitation). These multiplexers are ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. They are available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts. All version are supported in a BRIC8 construction that occupies eight PXI 3U mechanical slots, one of which provides the PXI interface and power.
-
product
PXI Prototyping Module, 2-Slot, Dual 20-Pin GMCT
40-225A-802
The 40-225A PXI Prototyping Modules are stripped down versions of the 40-220A PXI Breadboard series. These are very basic, low cost prototype modules. They have no PXI interface but do have access to fused power supplies from the PXI backplane.
-
product
EBIRST 9-pin Male D-type Termination Fixture
93-003-103
eBIRST is a range of USB controlled test tools capable of performing automated path resistance tests on Pickering Interfaces PXI, LXI or PCI controlled switching solutions. Each tool simply interfaces with the switching system's connector so a test can be run using the supplied Windows-based software.
-
product
Avionics PXI Express (PXIe) Interface Card - Multi-Channel, Multi-Protocol, 1553, ARINC, WMUX Interface for PCIe
Alta Data Technologies’ PXI Express interface modules offer a wide range of MIL-STD-1553, ARINC and WMUX configuration options using Alta’s PMC cards on a single-slot PXI Express 3U carrier. The cards are based on the industry’s most advanced 32-bit FPGA protocol engines, AltaCore™, and by a feature-rich application programming interface, AltaAPI™ (with LabVIEW SDK).
-
product
PXI Prototyping Module, 2-Slot, 37-Pin D-Type
40-225A-202
The 40-225A PXI Prototyping Modules are stripped down versions of the 40-220A PXI Breadboard series. These are very basic, low cost prototype modules. They have no PXI interface but do have access to fused power supplies from the PXI backplane.
-
product
20 Slot, 6U PXI Chassis
GX7000 Series
The GX7000C Series are high-performance 20-slot PXI chassis that can accommodate up to 19 instruments as well as a PXI controller (an embedded CPU or a PXI bus expander interface such as the MXI series). The 6U form-factor provides the necessary real estate to accommodate high performance and high-density test instrumentation, while offering the flexibility of being able to use 3U PXI and cPCI instruments as well.
-
product
PXI High Density MUX BRIC, 40-Chan, 20-Pole
40-570-315
This range of High-Density Multiplexer is part of our BRIC family. These MUX's are designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is also possible, without limitation). These multiplexers are ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. They are available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts. All version are supported in a BRIC8 construction that occupies eight PXI 3U mechanical slots, one of which provides the PXI interface and power.
-
product
PXI Prototyping Module, 1-Slot, 25-Pin D-Type
40-225A-301
The 40-225A PXI Prototyping Modules are stripped down versions of the 40-220A PXI Breadboard series. These are very basic, low cost prototype modules. They have no PXI interface but do have access to fused power supplies from the PXI backplane.
-
product
PXI High Density MUX BRIC, 10-Chan, 80-Pole
40-570-115
This range of High-Density Multiplexer is part of our BRIC family. These MUX's are designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is also possible, without limitation). These multiplexers are ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. They are available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts. All version are supported in a BRIC8 construction that occupies eight PXI 3U mechanical slots, one of which provides the PXI interface and power.
-
product
PXI LIN Interface Module
The PXI LIN Interface Module is a bus interface for developing applications with the NI-XNET driver. The NI-XNET device-driven DMA engine couples the LIN bus to host memory to minimize message latency. You can import, edit, and use signals from LIN Description File (LDF) databases in integrated LIN databases. PXI LIN Interface Modules work well for applications requiring real-time, high-speed manipulation of many LIN frames and signals, such as hardware-in-the-loop simulation, rapid control prototyping, bus monitoring, and automation control.
-
product
PXIe-5622, 150 MS/s, 16-Bit PXI IF Digitizer
780412-01
150 MS/s, 16-Bit PXI IF Digitizer—The PXIe‑5622 includes onboard signal processing (OSP), which enables features such as quadrature digital downconversion (DDC), real DDC, and anti-alias filtering. The PXIe‑5622 is ideal for communications applications because of its high dynamic range front end and a high-throughput PXI Express interface that allows it to stream IF data to disk for hours at the full sample rate.
-
product
EBIRST 78-pin D-type Test Tool
93-006-001
The 93-006-001 eBIRST 78-pin D-type test tool is part of a range of USB controlled test tools capable of performing automated path resistance tests on Pickering Interfaces PXI, LXI or PCI controlled switching solutions. Each tool simply interfaces with the switching system's connector so a test can be run using the supplied Windows-based software.
