Synchronization Modules
-
Product
PXI Prototyping Module, 1-Slot, 37-Pin D-Type
40-225A-201
-
The 40-225A PXI Prototyping Modules are stripped down versions of the 40-220A PXI Breadboard series. These are very basic, low cost prototype modules. They have no PXI interface but do have access to fused power supplies from the PXI backplane.
-
Product
PXI/PXIe RF Multiplexer, Single 16-Channel, 3GHz, 50Ω, SMB
42-875A-001
-
The 40-875A-001 (PXI) and 42-875A-001 (PXIe) are single 50 Ohm 16-channel RF multiplexers in a single slot. They have been designed to exhibit low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost.
-
Product
PXI 23 Channel Low Thermal MUX
40-620-022
-
Pickering 40-620 Multiplexer modules are similar to other Pickering Multiplexer cards except thermal EMF is substantially reduced to <1.5V with 250nV thermal stability. Typical applications include signal routing in ATE, selecting thermocouple inputs, switching amplifier gain circuits and high accuracy DC microvolt measurements.
-
Product
PXI Breadboard Module, 1-Slot, 15-Pin D-Type
40-220A-601
-
The 40-220A series of breadboard modules allow the user to construct their own circuit in situations where a suitable PXI module is not available. For example when it is required to integrate a non-switching function into a PXI chassis. Typical applications include: Creating custom circuitry that can be housed in on a 3U board, or to build special one-off switching modules.
-
Product
PXI Dual 4 to 1 RF Multiplexer 6GHz 50 Ohm SMA Terminated
40-882-002
-
This PXI multiplexer exhibits low VSWR characteristically over the full operating frequency range and consistent insertion loss characteristics. The use of solid state switches ensures a long service life with no wear out mechanism, making the 40-882 MUX ideal for ATE systems requiring frequent and fast operating RF switching.
-
Product
PXI High Density MUX BRIC, 24-Chan, 20-Pole
40-570-313
-
This range of High-Density Multiplexer is part of our BRIC family. These MUX's are designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is also possible, without limitation). These multiplexers are ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. They are available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts. All version are supported in a BRIC8 construction that occupies eight PXI 3U mechanical slots, one of which provides the PXI interface and power.
-
Product
High-Performance Autoranging DC Power Module, 20V, 50A, 500W
N6755A
-
The Keysight N6755A is a 500 W high-performance, autoranging DC power module that provides low noise, high accuracy and programming speeds that are up to 10 to 50 times faster than other programmable power supplies. Optional high-speed test extension offers an oscilloscope-like digitizer that increases measurement accuracy when viewing high-speed transient or pulse events within the device-under-test (DUT).
-
Product
Computer-On-Module
Qseven®
-
Qseven is an off-the-shelf, multi-vendor, computer-on-module that integrates all the core components of a common x86 PC and is mounted onto an application specific carrier board. A single ruggedized 230-pin MXM connector provides the carrier board interface to carry all the I/O signals to and from the Qseven module.
-
Product
LXI Microwave Multiplexer, SP4T, 7-Bank, 50GHz, 50Ω, SMA-2.4
60-803-607
-
Our 60-803-607 is a 7 bank SP4T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 50GHz. The 60-803 range is capable of supporting up to 16 banks of 4 channel multiplexers it is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
Product
PXI/PXIe MEMS Optical MUX, 4-Channel, Multi-Mode, 62.5/125 Fiber, SC/PC Connectors
42-850A-214-M62.5
-
The 40/42-850A-214-M62.5 is a PXI/PXIe 4-channel multiplexer with SC/PC connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules.
-
Product
PXI/PXIe Microwave Multiplexer, Triple SP4T, 67 GHz, 50 Ω, SMA-1.85, Remote Mount, Terminated, Failsafe
40-785C-473-TE
-
The 40-785C-473-TE (PXI) and 42-785C-473-TE (PXIe) are triple failsafe SP4T 67 GHz with automatic termination of unused signals and remotely mounted relays. The 40/42-785C range of multiplexers are available in single or dual, SP6T or SP4T configurations with relays mounted on the front panel. Remote versions are also available which can support up to three multiplexers in a single slot.
-
Product
SMARC® 2.1 Short Size Module With Intel® Core™ I3 Processors, Intel® Processors N Series And Intel® 7th Gen Atom® X7000E Processors
LEC-ALN
-
The ADLINK LEC-ALN is a SMARC module that supports up to 8 cores Intel® Core™ i3 (i3-N305, i3-N300) Processors, Intel® Processors N Series (N97, N50) and Intel® Atom® x7000E (x7425E, x7213E, x7211E) Processors (formerly Alder Lake-N) with integrated Intel® UHD graphics and high-speed interfaces. LEC-ALN modules support up 16GB LPDDR5 memory, up to 256GB eMMC storage (build option) and are also available with rugged operating temperature range and low power envelope, making them a perfect match for mission critical fanless edge computing applications that require safety and reliability at all times.
-
Product
PXI Quad 4 To 1 RF Multiplexer, 8GHz 50 Ohm SMA, Terminated
40-882A-004
-
The 40-881A-004 is a quad 50Ω 4 to 1 RF multiplexer with 8GHZ bandwidth.The 40-881A range of multiplexers have automatic termination of unused signals and are available as a single MUX in one PXI slot, a dual MUX in two PXI slots, or triple and quad MUXs in three slot PXI modules.
-
Product
LXI Single 32 Channel Fiber Multiplexer SC, Multi-Mode
60-851-214
-
The 60-850 and 60-851 are LXI conformant fiber optic multiplexers that use MEMS switching technology to ensure fast and reliable switching of single-mode (60-850) or multi-mode (60-851) optical signals being carried on fiber connections. The 60-850/851 is available with a variety of connector options and in a variety of multiplexer arrangements. Loop-thru versions are also available for easy multiplexer expansion.
-
Product
Single 16 to 1 Terminated 50 600MHz PXI RF Multiplexer
40-765-001
-
This 4 to 1 multiplexer is part of a range of RF multiplexers available in the following configurations: dual, quad and octal 4 to 1, single, dual and quad 8 to 1, single and dual 16 to 1 and single 32 to 1. All multiplexers have the option of automatic terminations which offer advantages at system level by reducing the presence of standing waves in the system which can cause degradation in isolation and crosstalk.
-
Product
8GB SO-DIMM DDR5-5600 262Pin 1GX16 1.1V Unbuffered Hynix Chip
AQD-SD5V8GN56-HC
-
Hynix Original Chip, Increased Banks and Burst Length, DDR5 5.6GT/s. Same-Bank Refresh, On-die ECC for Enhanced RAS.
-
Product
Power, Module, Receiver, CASS, 76 Position
510114107
-
Module, ID, Cass, Signal, 76 Positions, Discrete Wiring
-
Product
PXI Prototyping Module, 2-Slot, 25-Pin D-Type
40-225A-302
-
The 40-225A PXI Prototyping Modules are stripped down versions of the 40-220A PXI Breadboard series. These are very basic, low cost prototype modules. They have no PXI interface but do have access to fused power supplies from the PXI backplane.
-
Product
PXI 2A Multiplexer, 2-Bank, 64-Channel 1-Pole
40-614-010
-
The 40-614 High Density 2 Amp multiplexer module is available in 20 configurations. All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 200VDC/140VACThe module is suitable for signal routing in ATE and data acquisition systems. User connections are made via a front panel 160-pin DIN 41612 connector which is fully supported by our range of cabling and connector solutions.
-
Product
LXI Microwave Multiplexer, SP4T, 1-Bank, 50GHz, 50Ω, SMA-2.4
60-803-701
-
Our 60-803-701 is a 1 bank terminated SP4T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 50GHz. The 60-803 range is capable of supporting up to 14 banks of terminated 4 channel multiplexers it is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
Product
IDoor Module: 2-Port Hilscher NetX100 FieldBus MPCIe, EtherNet/IP, RJ45
PCM-26R2EI
-
Meets Advantech Standard iDoor TechnologyPCI ExpressR Mini Card Specification Revision 1.2 compliantIdentical interface for all Hilscher Real-Time Ethernet Fieldbus ProtocolsVarious colorful front plates for protocol identificationEasy integration by wide range of device driversHigh extended temperature range up to 70°CCompatible with embedded automation PC UNO-1/2/3/4 series
-
Product
LXI Microwave Multiplexer, SP4T, 5-Bank, 26.5GHz, 50Ω, SMA
60-803-305
-
Our 60-803-305 is a 5 bank terminated SP4T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 26.5GHz. The 60-803 range is capable of supporting up to 14 banks of terminated 4 channel multiplexers it is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
Product
PXI/PXIe Microwave Multiplexer, Single SP10T, 18 GHz, 50 Ω, SMA, Failsafe
40-788-121
-
The 40-788-121 (PXI) and 42-788-121 (PXIe) are single failsafe SP10T 18 GHz unterminated microwave multiplexers. The 40/42-788 range of multiplexers are available as single or dual, SP8T, SP10T or SP12T panel mounted multiplexers with relays mounted on the front panel. Remote versions are also available which can support one or two multiplexers in a dual slot module.
-
Product
PXI 2 Amp MUX, Dual 16-Channel 2-Pole
40-635-006
-
The 40-635 2 Amp Multiplexer module is available in 9 standard configurations as well as 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.The module is suitable for signal routing in ATE and data acquisition systems. Connections are made via a front panel 78-way D-type connector.
-
Product
PXI 2A Multiplexer, 1-Bank, 4-Channel 32-Pole
40-614-020
-
The 40-614 High Density 2 Amp multiplexer module is available in 20 configurations. All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 200VDC/140VACThe module is suitable for signal routing in ATE and data acquisition systems. User connections are made via a front panel 160-pin DIN 41612 connector which is fully supported by our range of cabling and connector solutions.
-
Product
PXI Quad 4 to 1 Mux 1.3GHz 50Ohm SMA
40-749-521
-
The 40-749 is a quad 4 to 1 RF MUX available in 50 Ohm or 75 Ohm versions occupying a single PXI slot. The module is available with SMB or SMA connectors for 50 Ohm versions or, 1.0/2.3 or Mini SMB connectors for 75 Ohm versions. Applications for the 40-749 include routing high frequency signals to and from oscilloscopes, analyzers, signal generators and synthesizers, telecoms tributary switching, video/audio switching and switching high frequency logic signals.
-
Product
PXI Replacement Microwave Multiplexer Relay
40-785-751-R
-
Pickering Interfaces PXI Microwave multiplexer modules are suitable for switching 50Ω signals up to 40GHz. The 40-785 is available as a single or dual 6 channel multiplexer, with relays mounted on the front panel. The single slot version can support up to three supplied remotely mounted multiplexers.
-
Product
PXI Solid State Versatile Multiplexer
40-683-001
-
The 40-683 Very High Density Versatile Multiplexer module features a wide range of selectable switching configurations. The 40-683 is especially useful where a high density MUX array is required that can adapt to different test configurations for different test targets, or where a test system may have to be reconfigured in the future. The 40-683 uses high performance solid state switching to ensure a service life of greater than 10 years and fast operation.
-
Product
PXI Prototyping Module, 1-Slot, 78-Pin D-Type
40-225A-401
-
The 40-225A PXI Prototyping Modules are stripped down versions of the 40-220A PXI Breadboard series. These are very basic, low cost prototype modules. They have no PXI interface but do have access to fused power supplies from the PXI backplane.
-
Product
Blank Module, Receiver/ITA, 1 Module Position, 90 Series Modules
510104118
-
Blank modules are for unused module slots. The blank shielding module fills a module slot and shields signals between the modules. Blank modules fit in either ITA or receiver positions.
