-
product
Proving Unit & Voltage Tester Kit
DLPK1
Touch electrode for Quick testing of fused leads Optical and acoustic continuity Indication Low battery indication A portable, battery powered Proving Unit for testing Two Pole Voltage Testers up to 690V Continuity Tester for testing: Fuses, Fused test leads etc
-
product
Battery Extra Load Units
Performing capacity/discharge test on a high-capacity battery may be challenging since high requirements are set on the discharge system. In cases when discharge test times need to be reduced, high load capacities are required from the discharge system. The battery extra load unit BXL is an additional load unit designed especially for this purpose.It is primarily used with BLU battery testers. However, the unit is a universal add-on device. This means it can be used as an additional load with any other discharge/capacity tester in the market.When discharge current exceeds the capacity of a single BLU device, extra load unit increases discharge capacity. A system of BLU and BXL instruments enables performing the capacity test in an accurate, user-friendly way in accordance to battery testing standards: IEEE 450-2010, IEEE 1188-2005, IEEE 1106-2015, IEC 60896-11/22, and other relevant standards.
-
product
Fiber Visual Fault Locator
Fiber visual fault locator is a pen type device which is able to locate the breakpoint, bending or cracking of the fiber glass,this small fiber optic equipment can locate the fault of OTDR dead zone and make fiber iIdentification from one end to the other end .
-
product
Emergency Power Supply Units (EPSU) (24) 5-15R 0U V
EPS-2415-V60
EPSU Power (Basic / Surge / Metered / Value) – rack mountable power distribution, 120V, optional surge suppression, and amp meter
-
product
Power Supply Units
converts mains AC to low-voltage regulated DC power for the internal components of a computer. Modern personal computers universally use switched-mode power supplies.
-
product
Combo Unit, 7.5 Digit Digital Multimeter (DMM) with 10-Bit 1GHz Digitizer in a Single VXI Slot
6084A
Increases test system performance and density with this combo unit, which packages a 7.5 digit Digital Multimeter (DMM) together with a 10-bit, 1 GHz Digitizer into a single VXI slot.Replaces the Wavetek 1362 DMM, Analogic DBS Series, and Agilent VXI DigitizersDigitizer with 4 Inputs, 10-bits, 1 GHz, up to 4 GS/s and Ranges up to 500V DMM with 7.5 Digits for DC Volts, Current and Ohms with AC Volts up to 1 MHzIVI-COM Drivers and Soft Front Panels ProvidedMore Dynamic Range (by 20 dB for DMM and 12 dB for Digitizer) for Better Legacy Range Mapping
-
product
Visual Fault Locators
Optical Wavelength Laboratories
OWL fiber optic visual fault locators (VFL) are specially designed to couple a maximum of optical energy into multimode and singlemode optical fibers by using a bright red fiber optic laser. Breaks, microbends, and other anomalies in optical fibers and connectors cause the intense bright red laser light to escape, thus revealing the presence of a fault. In addition to visual fault location, OWL VFLs can be used as a visual optical fiber identifier. A visual fiber optic identifier eliminates much of the guesswork during testing by identifying the fiber under test.
-
product
Electronic Control Units
Self-contained engine management system and data logger for race engines up to eight cylinders. The unit is complete with integrated ignition and injection drivers and so needs no external units to run an engine.
-
product
Cable Fault Locator
TW3304N
Techwin(China) Industry Co., Ltd
The Perfect Handhold Tester Series Cable Fault Locator TW3304N is the most portable test instrument in the industry. It adopts the OTDR technical principles and integrates the powerful analysis software, which enables the TW3304N fiber ranger detect fiber faults location more accurate and easy.
-
-
product
Visual Fault Locator
OrienTek Optical Technology Ltd.
powerful, mini visual laser source for fiber fault locating. It has attractive design and small size and it is easy to operate. ● Bright red laser at 650nm● Pulsed and CW operation● Outpower: 1mw,10mw,20mw,30mw● 2.5mm universal connector● 40 hours of operation(1mW)● Pocket size design● 1.25 mm adapter for LC (optional)
-
product
Precision Source / Measure Unit, 1 CH, 1 PA Resolution, 21 V, 1.5 A
B2901BL
The Keysight B2901BL precision source / measure unit (SMU) is a 1-channel, compact, and cost-effective benchtop SMU with the capability to source and measure both voltage and current with high accuracy. The 4-quadrant source and measurement capabilities enable taking I/V measurements without configuring multiple instruments.
-
product
Multi-Channel Attenuation Control Unit (4-channels), DC to 18 GHz, 0 to 121 dB, 1 dB Step
J7204B
The J7204B is a multi-channel (4-channels) attenuation solution for signal attenuation and conditioning of up to 4 devices under test (DUT). Operating frequency from DC to 18 GHz, with 121 dB, 1 dB steps. Exceptional 0.03 dB insertion loss repeatability per section for the entire 5 million cycles and excellent attenuation accuracy and flatness, the J7204B reduces cost of ownership and provide the best measurement accuracy.
-
product
Exclusive Control Unit For Safety Light Curtain
SF-C10
Panasonic Industrial Devices Sales Company of America
Exclusive Control Unit For Safety Light Curtain
-
product
Power Profiler, DC Energy Analyzer, Power Supply, Digital Multimeter, Source Measure Unit, Power Debugger
Otii Ace Pro
Otii Ace Pro is the big brother to Otii Arc, and is an instrument that can precisely source voltage (up to 25 V) and current (up to 5A) and simultaneously measures voltage and/or current with a high sample rate (50ksps) and low step size. It computes power and energy and enables engineers and developers to easily see and optimize the energy consumption and battery life of their devices under test.
-
product
Fault Locator
BIDOYNG
BIDOYNG fits into existing LV fuse positions using two LV fuses in parallel, creating a robust single-shot auto-recloser. The primary fuse carries the load current until a fault causes it to operate. Then, after a user programmed delay, the secondary fuse is switched in and the network re-energised without customer interruption.
-
product
Underground Fault Location
Schweitzer Engineering Laboratories, Inc.
Underground faulted circuit indicators identify the faulted cable section without a time-consuming re-fuse and sectionalize process. Applications include subsurface or pad-mounted transformers, switchgear, sectionalizing cabinets, junction boxes, and splices.
-
product
PXI-8511, 1‑ or 2-Port, Low-Speed/Fault Tolerant PXI CAN Interface Module
780686-02
1‑ or 2-Port, Low-Speed/Fault Tolerant PXI CAN Interface Module—The PXI‑8511 is a fault-tolerant Controller Area Network (CAN) interface for developing applications with the NI‑XNET driver. The PXI‑8511 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimize message latency and freeing host processor time for processing complex models and applications.
-
product
Programmable AC&DC Power Supply Unit
PADS
The energy feedback type programmable AC/DC power source with energy feedback unit equipped functions of voltage adjustable, frequency adjustable, harmonic controllable, low voltage ride through simulation etc.
-
product
650nm Visual Fault Locator
Shanghai Baudcom Communication Device Co.,Ltd.
Visual Fault Locator series Visual Fault Locator uses the DFB-LD as the emitting component. Driven by constant current source, the indicator can emit stable red laser.The product can be used to inspect fiber failure when they connect with optical interface and be inserted into single mode or multi mode optical fiber.It is indispensable tool in fiber project constructing, fiber net-work maintaining, optical component manufacture and research.
-
product
PXI 10A Fault Insertion Switch 6-chan 2-bus
40-192-012
This PXI fault insertion switch uses solid state switching elements and is capable of switching current up to 10A. It is designed to be able to insert three different fault conditions between the test fixture and the equipment under test: Open-Circuit. Short-Circuit between UUT connections. Short-Circuit to external signals. Through relays on each channel enable signals to the UUT to be set open-circuit. Fault Insertion Buses allow any channel to be shorted to any other channel and also enable any channel to be connected to an external signal such as Power, Ignition or Ground to simulate fault conditions. The module is supplied with 2 fault buses.
-
product
Manual Fixture Kit with Changeable Cassette, Max number of probes (2N) 1000 Units, Max UUT 450x330MM (wxd)
CMK-07
Linear click system with ball bearings, using gas springs. 10 mm ESD-proof top cover with aluminum reinforcement bars. Steel base cabinet with detachable aluminum back and bottom panels.Detachable interchangeable case system with an 8 mm spring-loaded probe protection cover.Base cabinet fitted with a telescopic guide rail and catch.
-
product
Multi-Channel Attenuation Control Unit (5-channels), DC to 6 GHz, 0 to 121 dB, 1 dB Step
J7205A
The J7205A is a multi-channel (5-channels) attenuation solution for signal attenuation and conditioning of up to5 devices under test (DUT). Operating frequency from DC to 6 GHz, with 121 dB, 1 dB steps. Exceptional 0.03 dB insertion loss repeatability per section for the entire 5 million cycles and excellent attenuation accuracy and flatness, the J7205A reduces cost of ownership and provide the best measurement accuracy.
-
product
PXIe-2515, 35-Channel, 0.25 A PXI Signal Insertion Switch Module
780587-15
PXIe, 35-Channel, 0.25 A PXI Signal Insertion Switch Module—The PXIe‑2515 is a multiplexer switch module that enables connectivity by routing high-speed digital I/O (DIO) signals between a device under test (DUT) and an NI high-speed DIO device or a parametric measurement device. You can use modules such as PXI Source Measure Units (SMUs) and PXI Digital Multimeters (DMMs) with high-speed digital devices. With the PXIe‑2515, you can perform parametric tests on digital pins without external connectivity or impedance mismatch challenges.
-
product
3U cPCI Sensor Interface Unit
SIU33
NAI's SIU33 is a highly configurable rugged COTS system or subsystem ideally suited for rugged military, industrial, and commercial applications that require high-density I/O, communications, Ethernet switching, and processing. The SIU33 uses up three NAI field-proven, 3U cPCI boards to deliver off-the-shelf, SWaP-optimized COTS solutions that "Accelerate Your-Time-to-Mission."
-
product
Linear Vibration Motor Aging Unit
BK2019A
The BK2019A Linear Vibration Motor Aging Test System was designed to test your linear vibration motors for long term reliability. It can test 20 DUT’s at one time and you can stack them easily so you can test hundreds of DUT’s simultaneously in a small space. This is a great machine to ensure your product will do its job for it's expected life.
-
product
12/24 CH Insertion Loss/Return Loss Automatic Testing System
CA3201
UC INSTRUMENTS CA3201 12/24 CH INSERTION LOSS/RETURN LOSS AUTOMATIC TESTING SYSTEM is special designed for MPO/MTP fiber cable and multi-channel fiber optical devices like PLC device. It also can be easy changed into AWG DWDM devices testing system ifwe change 1310 /1550 nm light source into UC INSTRUMENTS’ tunable laser source.
-
product
GPIB-RS232, Instrument Control Device - United Kingdom 240VAC
779732-06
The GPIB‑RS232 is an IEEE 488 controller device for computers with an RS232 port. You can use this device to integrate an instrument into your system using GPIB. This device transforms a computer with an RS232 serial port into a talker, listener, or controller on the GPIB bus. It can also interface RS232 instruments and peripherals to the GPIB bus. It can implement the physical and electrical specifications of the IEEE 488 and RS232 standards, as well as interpret and execute high-level commands from the serial port, including RS232‑to‑GPIB and GPIB‑to‑RS232 protocol conversions. This device is IEEE 488.2 compatible. The device includes a license for the NI‑488.2 driver software, providing maximum reliability for connecting to third-party instruments with GPIB.
-
product
4 10/100M LAN FTTH EPON ONU ( Optical Network Unit )
ONU-4FE
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai ONU-4FE optical network unit (ONU), based Gigabit Ethernet Passive Optical Network FTTH EPON system user side equipment, combined EPON OLT (Optical Line Terminal) via a passive optical network PON, to achieve a multipoint (P2MP) high-speed data transmission. Provides powerful data, voice and video and other broadband services to users..
-
product
Power Units- AC Ionising Equipment
is an advanced AC power supply. It is compatible with all Meech AC Ionisers.
