Interface Devices
soft and hard handshake between devices.
-
Product
500-Pin SEARAY Cable Assembly, Male to 5x50-Pin D-Type, 2 Amp, 1m, 250 Port
A500RMR-05F050D5C100
Cable Assembly
The 500-Pin SEARAY connector is used on switching products to provide a very high density 2A connector solution that is suitable for use to 200VDC. The male SEARAY connector of this cable assembly is suitable for direct connection to Pickering Interfaces products. Five 50-Pin D-Type connectors allow an interface to other devices. Screwlocks are provided at both ends to secure the cable assembly to mating products.
-
Product
Modulator
SFT3306I
-
Hangzhou Softel Optic Co., Ltd.
SFT3306I 6in1/16in1 ISDB-T modulator is the latest generational Mux-modulating device developed by SOFTEL. It has 6 (or16) multiplexing channels and ISDB-T modulating channels, and supports maximum 192 (or 512) IP input through the 3 GE ports and 6 (or16) ISDB-T non-adjacent carriers (50MHz~960MHz) output through the RF output interface. The device is also characterized with high integrated level, high performance and low cost. This is very adaptable to newly generation DTV broadcasting system.
-
Product
SPI Isolators
-
SPI (Serial peripheral interface) is one of the most widely used interfaces between microcontrollers and peripheral ICs such as sensors, ADCs, DACs, shift registers, SRAM, and others. Analog Devices has your isolated SPI bus covered with our dedicated SPI digital isolators which support this synchronous, full duplex master-slave-based interface. Options include devices built with ADI's proven iCoupler® technology and offering a small footprint, simple design-in, fast speeds, and high data integrity, as well as integrated µModules which require no external components. Our SPI isolator solutions increase performance and reduce board space. This simple, compact solution is ideal for isolated SPI data requiring communication across different ground potentials or through large common mode transients often found in Industrial PLCs (programmable logic controllers) and Instrumentation and data acquisition systems.
-
Product
Tone Coax Cable Generator
240 HAL
-
The AINES 240 HAL Tone Generator is a water resistant tone generator equipped with a weathertite 2 conductor modular cord and jack. The set can be connected to the Network Interface Device (NID) with either the two individual clips or the modular cord. This allows the CPE circuit to be viewed in both directions, towards the Central Office and towards the customer premise. In the event the CPE does not have a jack, but instead has a cord, plug the cord into the Model 240s jack and transmit tone!
-
Product
USB-8506 , LIN Interface Device
784664-01
LIN Interface
1- or 2-Port, USB LIN Interface Device—The USB‑8506 is a Local Interconnect Network (LIN) interface for developing applications with the NI‑XNET driver. The USB‑8506 is powered over the USB bus and does not require external power. The USB‑8506 excels in applications requiring logging or manipulation of hundreds of LIN frames and signals, such as in-vehicle data logging, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move LIN frames and signals between the interface and the user program without CPU interrupts, minimize message latency, and free host processor time. The USB‑8506 is available with a three‑pin COMBICON synchronization connector for triggering and synchronizing the internal hardware timebase with other devices.
-
Product
GPIB-ENET/1000, Ethernet GPIB Instrument Control Device - Brazil 127/220VAC
781630-12
GPIB Controller
The GPIB‑ENET/1000 is an IEEE 488 controller device for computers with an Ethernet port. You can use this device to share a single GPIB system among many networked users or to control several test systems from a single networked host. The GPIB‑ENET/1000 features a password-protected web interface for easy configuration. It can also control IEEE 488 devices from anywhere on an Ethernet‑based (LAN) TCP/IP network (Gigabit, 100BASE‑TX, 10BASE‑T). Each device interfaces to and shares up to 14 GPIB devices from several network hosts, and you can control up to 100 GPIB‑ENET/1000 interfaces with a single computer. The device includes a license for the NI‑488.2 driver software, providing maximum reliability for connecting to third-party instruments with GPIB.
-
Product
Multi-Interface TDM, Optical, And Packet/IP Rackmount & Probe Test Platforms
mTOP™
-
Most equipment manufacturers and large enterprises prefer rack-based test tools as they are compact and higher density form factor solution for testing, monitoring, and troubleshooting network conditions. GL’s Multiple TDM Optical and Packet (mTOP™) rack enclosure can house any combination of USB based test equipment which are easily deployed and securely fixed to an equipment rack to provide extraordinary scalability to test switches, routers and end-to-end networks. These rack based platforms incorporates the basic test unit along with the necessary PC hardware, Windows® 10 64-bit operating system and remote accessibility via scripting and remote desktop. There are no moving parts with the unit, so reliability and longevity are integral. GL’s latest mTOP™ Probe stand-alone hardware variant is an all-in-one self-contained test instrument. The mTOP™ Probe can include any of the multiple TDM Optical and Packet interfaces USB device combined with the PC into one single box. The comprehensive mTOP™ Probe hardware unit is designed for easier portability and convenient for field testing which incorporates the testing features for multiple interfaces along with necessary PC hardware in a single box. GL’s USB based test equipment - PacketExpert™ (Ethernet), tProbe™ (T1/E1), USB T3/E3 (TDM), Dual UTAs (Analog/Wireless), and LightSpeed1000™ (SONET SDH) to support multiple interfaces in a compact rack space or included in a portable Probe unit.
-
Product
PCIe-8431, PCI Express, 16-Port, RS485/RS422 Serial Interface Device
780592-02
Serial Interface
The PCIe‑8431/16 is a high-performance interface for high-speed communication with RS485 and RS422 devices. It features high-performance DMA transfers, multithreading, and multiprocessor support. You can also select between 4‑ and 2‑wire transceiver modes for full‑ and half‑duplex communication. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
Product
500-Pin SEARAY Cable Assembly, Male to 5x50-Pin D-Type, 2 Amp, 0.5m, 250 Port
A500RMR-05F050D5C050
Cable Assembly
The 500-Pin SEARAY connector is used on switching products to provide a very high density 2A connector solution that is suitable for use to 200VDC. The male SEARAY connector of this cable assembly is suitable for direct connection to Pickering Interfaces products. Five 50-Pin D-Type connectors allow an interface to other devices. Screwlocks are provided at both ends to secure the cable assembly to mating products.
-
Product
USB-8452, 3.3 MHz I2C, 50 MHz SPI I2C/SPI Interface Device
781964-02
Interface Module
The NI USB‑8452 is a master interface for connecting to and communicating with inter-integrated circuit (I2C) and serial peripheral interface (SPI) devices. With plug‑and‑play USB connectivity, the USB‑8452 is a bus-powered, portable solution to communicate with consumer electronics and integrated circuits. It also includes eight general-purpose digital I/O lines for a variety of applications, such as configuring the address of I2C devices, toggling LEDs, or strobing convert and data ready lines common to analog converter chips. You can physically place the USB‑8452 more closely than PCI interfaces to I2C/SPI devices, which reduces I2C bus length and minimizes noise problems. Additionally, the interface provides +5 V and GND to power circuits with no external power supply.
-
Product
PCIe - High Performance Radios
-
Supports up to 150 Mbps data rateCompliant with IEEE802.11 b/g/n standardsCompliant with IEEE 802.11b, 802.11d, 802.11e and 802.11g standards and the 802.11i specification Includes signal-sustain technology (SST) rate-over-range enhancements such as low-density parity check (LDPC), and maximum likelihood demodulation (MLD)Supports all mandatory IEEE 802.11n features as well as several optional features such as HT40, half-guard interval in HT40 and Rx space-time block coding (STBC)Supports low-power sleep modes and wake-on-wireless (WoW) LANFeatures the Atheros AR3012 Bluetooth 4.0 + HS chipset and Bluetooth Class 1 RadioUSB 2.0 device interface supports standard HCI USBRoHS compliant
-
Product
Analog Device Interface
ADI-123
-
Model ADI-123 Analog Device Interface offers the means of computer interfacing almost on any device whic is provided with dc inputs and/or outputs, for example programmable power supplies and measuring instruments of all kinds.
-
Product
USB-485/4, 4-Port, USB, RS485/RS422 Serial Interface Device
778476-54
Serial Interface
The USB‑485/4 interface transforms your USB port into a single asynchronous serial port for communication with RS485 and RS422 devices. You can use a USB‑485/4 port as a standard serial port from your application, including RTS/CTS hardware handshake lines. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
Product
PCIe-8432, PCI Express, 2-Port, Isolated, RS232 Serial Interface Device
781744-01
Serial Interface
The PCIe‑8432/2 is a high-performance interface for high-speed, port-to-port isolated communication with RS232 devices. It features high-performance DMA transfers, multithreading, and multiprocessor support. NI serial … interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
Product
USB-485/4, 4-Port, USB, RS485/RS422 Serial Interface Device
778476-104
Serial Interface
The USB‑485/4 interface transforms your USB port into a single asynchronous serial port for communication with RS485 and RS422 devices. You can use a USB‑485/4 port as a standard serial port from your application, including RTS/CTS hardware handshake lines. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
Product
USB Connectivity Bridges
USBXpress
-
Silicon Labs USBXpress devices are highly optimized solutions that enable designers to easily add USB to existing and new applications. These fixed function devices provide the easiest method to add USB without the need for any firmware or driver development. USBxpress portfolio supports several USB to serial bridge devices including human interface (HID) devices and USB Audio devices.
-
Product
500-Pin SEARAY Cable Assembly, Male to 5x50-Pin D-Type, 2 Amp, 0.5m, 250 Port
A500RMR-05F050D4B050
Cable Assembly
The 500-Pin SEARAY connector is used on switching products to provide a very high density 2A connector solution that is suitable for use to 200VDC. The male SEARAY connector of this cable assembly is suitable for direct connection to Pickering Interfaces products. Five 50-Pin D-Type connectors allow an interface to other devices. Screwlocks are provided at both ends to secure the cable assembly to mating products.
-
Product
PCI-8531, 1-Port, CANopen Interface Device
781060-01
CAN Interface
The PCI‑8531 is a high-speed CANopen interface for developing applications with the NI‑Industrial Communications for CANopen driver. CANopen is the application layer that sits on top of the CAN physical layer often used for industrial automation … applications. CANopen was designed for motion-oriented machine control networks, such as handling systems, but now it is used in a variety of products and applications, including medical equipment, off-road vehicles, maritime electronics, public transportation, and building automation. The PCI‑8531 can transmit or receive process data objects (PDOs) and service data objects (SDOs) according to CiA‑DS 301. It also features a batch SDO editor with EDS file integration and LSS services support for slave node configuration.
-
Product
Audio Interfaces
-
Applied Research and Technolgy
Dedicated interfaces, multi-function devices with integrated digital connectivity, and task-specific recording tools.
-
Product
Aircraft Interface Devices
AID
Interface
Versatile Ballard Aircraft Interface Devices (AIDs) from Astronics offer a secure, open-architecture approach that empowers you to take control of your software and your data today and prepares you to leverage and incorporate the next-generation technologies of tomorrow, including the Internet of Things (IoT) for the aircraft.
-
Product
USB-232/4, 4-Port, USB, RS232 Serial Interface Device
778473-04
Serial Interface
The USB‑232/4 interface transforms your USB port into a single asynchronous serial port for communication with RS232 devices. You can use a USB‑232/4 port as a standard serial port from your application, including RTS/CTS hardware handshake lines. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
Product
Remote Controller
Remote Control Interface
ADLINK Bus expansion is a technology that increases the number of slots of the same or different bus type for a host computer system. ADLINK bus expansion product provides variety of interface options, including PCI, PCI Express, PXI, and ExpressCard to increase bus slots and leverage the latest computing power of both desktop and server-grade computers for a variety of applications. The interoperability of different bus interface devices, such PCI, PXI and PCI Express, is also a great benefit for those facing complicated system integration tasks. ADLINK bus expansion products also provide complete hardware and software transparency, without the need for additional drivers or software.
-
Product
PCIe-8430, PCI Express, 16-Port, RS232 Serial Interface Device
780591-02
Serial Interface
The PCIe‑8430/16 is a high-performance interface for high-speed communication with RS232 devices. It features high-performance DMA transfers, multithreading, and multiprocessor support. NI serial interfaces also appear as … standard COM ports for compatibility with programs that use serial communications.
-
Product
PCI-8516, 2-Port, PCI, LIN Interface Device
781365-01
LIN Interface
2-Port, PCI, LIN Interface Device—The PXI‑8516 is a Local Interconnect Network (LIN) interface for developing applications with the NI‑XNET driver. The PXI‑8516 excels in applications requiring real-time, high-speed manipulation of hundreds of LIN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move LIN frames and signals between the interface and the user program without CPU interrupts, minimize message latency, and free host processor time for processing complex models and applications.
-
Product
IVN-8561, Automotive Ethernet Interface Device
786169-01
Ethernet Interface
2-Channel, 4-Port, 100BASE-T1 to 100BASE-TX Automotive Ethernet Interface Device—The IVN-8561 is an interface that converts 100BASE-T1 unshielded twisted pair (UTP) automotive Ethernet to standard 100BASE-TX Ethernet. It is ideal for developing applications that require automotive Ethernet to test and validate automotive electronic control units (ECUs). The IVN-8561 provides two channels to convert data between 100BASE-TX Ethernet and 100BASE-T1 Automotive Ethernet. Each 100BASE-T1 port can be configured as master or slave, using switches on the front panel. The IVN-8561 also provides LED on the front panel so that you can monitor the linkage and activity on the various ports.
-
Product
USB-8502, 2-Port, High-Speed/FD, USB CAN Interface Device
784662-01
CAN Interface
1- or 2-Port, High-Speed/FD, USB CAN Interface Device—The USB-8502 is a high-speed controller area network (CAN) interface for developing applications with the NI‑XNET driver. The USB‑8502 is powered over the USB bus and does not require external power. It excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals such as bus monitoring, automation control, and more. The NI‑XNET device‑driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex applications. The USB‑8502 is available with a three‑pin COMBICON synchronization connector for triggering and synchronizing the internal hardware timebase with other devices.
-
Product
500-Pin SEARAY Cable Assembly, Male to 5x50-Pin D-Type, 2 Amp, 2m, 250 Port
A500RMR-05F050D5C200
Cable Assembly
The 500-Pin SEARAY connector is used on switching products to provide a very high density 2A connector solution that is suitable for use to 200VDC. The male SEARAY connector of this cable assembly is suitable for direct connection to Pickering Interfaces products. Five 50-Pin D-Type connectors allow an interface to other devices. Screwlocks are provided at both ends to secure the cable assembly to mating products.
-
Product
Automotive Ethernet Interface Device
Ethernet Interface
The Automotive Ethernet Interface Device converts unshielded twisted pair (UTP) Automotive Ethernet to standard Ethernet. This device is ideal for developing applications that require Automotive Ethernet to test and validate automotive electronic control units (ECUs). It includes ports for Automotive Ethernet connections and ports for 100BASE-TX Ethernet connections. You can use switches on the front panel to configure each 100BASE-T1 port as master or slave. The device also provides LED on the front panel so that you can monitor the linkage and activity on the various ports.
-
Product
RF Device Tester
RF ITS
-
Sterner's automated test management system, combined with integrated RF technology modules, provides full functionality, including: Apply power to the device under test (DUT). Read and write blocks of data to set up and validate product EEPROM using a hard-wired communications interface. Scan transmitting devices or traveller barcodes and write the information to the DUT (the "sign-up process"). Inject an RF signal of known frequency and power level to test receiver sensitivity.
-
Product
3.5” Embedded SBC With Intel® Pentium® Processor N4200 & Celeron® Processor N3350, LVDS, HDMI, 2 GbE LANs And Audio
CAPA313
-
The CAPA313 is powered by the Intel® Pentium® processor N4200 or Intel® Celeron® processor N3350 (codename: Apollo Lake). This 3.5" embedded board was designed for operational stability in harsh environments with a wide operating temperature range from -20°C to +70°C. It offers a wide range DC input of 12V to 24 for various industrial environments. It also comes with rich I/O connectors, stunning graphical performance and an emphasis on expandability. In addition to one 204-pin DDR3L-1867 SO-DIMM socket supporting system memory up to 8GB, the CAPA313 has one PCI Expess Mini Card slot for 3G/4G, GPS, Wi-Fi and Bluetooth connection. The compact-size embedded board comes with one RS-232/422/485, one RS-232, two USB 2.0, four USB 3.0, eight-channel digital I/O, audio, LVDS, HDMI, VGA (optional) and dual Gigabit LANs with Intel® i211AT Ethernet controller. It also features one SATA-600 socket and one mSATA interface for storage devices. To ensure reliable operation, the 3.5” embedded SBC supports watchdog timer and hardware monitoring features.
