Shock
A shock test transmits kinetic or thermal energy into a UUT in a relatively short interval in a controlled enviroment.
See Also: Thermal Shock, Vibration
-
Product
Pneumatic Vertical Shock Response Spectrum Test System
KRD14 series
-
KRD14 series pneumatic shock response spectrum tester is used to measure and determine the shock resistance of electrical and electronic products or packaging, and to evaluate the reliability and structural integrity of the test product in a shock environment. The shock response spectrum is the total result of a series of single-degree-of-freedom linear systems with different natural frequencies subjected to the same shock excitation response. When a product is subjected to an impact, the maximum value of its impact response means that the product has a maximum stress. Therefore, the shock response spectrum tester can better simulate the shock wave and shock energy suffered in the real environment.
-
Product
Shock Test Systems
-
Sanwood Environmental Chambers Co ., Ltd.
Is featured with advanced design, high degree of automation and reliability, simple operation and convenient maintenance. The system meets the requirements of both shock and collision test, can perform conventional half-sine wave, post-peak sawtooth wave, square wave and other waveform shock tests.
-
Product
Thermal Shock Test Chamber (Three Zone)
-
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell’s Thermal Shock Test Chamber (3 Zone) consist of the Test Zone, Heat Storage Zone and Cold Storage Zone. The specimen stay in test zone, hot and cold air will be blew from the storage zones to achieve rapid temperature change for thermal shock.
-
Product
Rain Penetration And Thermal Shock Tester
RAST
-
This is a user-friendly, three-in-one test stand for your operating convenience. Internal and external shock tests as well as rain penetration tests are all important for determining the quality and durability of your products and meeting all relevant international standards.
-
Product
Shock & Drop Testing
-
Shock testing is often performed as part of a hardware qualification or design process. Information obtained during shock testing can improve the survivability of products as well as verify that they will perform properly in service. These types of tests require special transducers and measurement systems to record and process the high level, high frequency response.
-
Product
Pneumatic Vertical Shock Test System
KRD11 series
-
KRD11 series pneumatic vertical shock test system is featured with advanced design, high degree of automation and reliability, simple operation and convenient maintenance. The system meets the requirements of both shock and bump test, can perform conventional half-sine wave, post-peak sawtooth wave, trapezoid wave and other waveform shock tests.
-
Product
Hardware-Software System
Shock Impact Recorder
-
This system is complex of recording instruments intended for measurement and recording of shock impact parameters produced by shock testing machines.
-
Product
Shock Control
-
Shock testing simulates an extreme event that a unit under test is exposed to during handling, shipment, explosive event and/or daily use (e.g. dropping an object). The profile for this type of testing is defined by the shape of the time domain waveform together with its amplitude and duration. The m+p VibControl vibration control system offers full functionality for classical shock and shock response spectrum testing as well as for tests using external pulses or the capture of transient signals.
-
Product
Vibration/Shock Testing
-
Quest Engineering Solutions provides a broad range of vibration testing and shock testing services. We have a variety of vibration test systems of different sizes and broad test capabilities. Vibration and shock testing and vibration analysis are important to achieving product quality. Our experience can help you choose the tests which will optimize your product's design and reliability.
-
Product
TSE-12-A Thermal Shock Chamber
-
Did you think that getting a thermal shock chamber was too expensive, required special utilities, and half your lab-space? The TSE-12 thermal shock chamber is the solution. Only 26 inches wide, the TSE-12 transfers product loads between cold and hot zones with a temperature range of -65°C to 200°C.
-
Product
Temperature Measurement IR Sensors & Detectors
ST60 LCC
-
A single-channel silicon-based thermopile in a LCC package for surface mount assembly in a small active area of 0.61mm x 0.61mm. Time constant of 18ms with Nitrogen encapsulation gas. Delivers a very low Temperature Coefficient of Responsivity of -0.04%/C. This detector has a very short thermal shock response to ambient temperature chang
-
Product
Sensors for Mobile Machines
-
*Inclination sensors with CAN or analog interface*Inductive sensors with high protection rating*Pressure sensors with a robust measuring cell for mobile hydraulics*High shock and vibration resistance*Wide operating temperature range
-
Product
General Purpose Piezoelectric Accelerometers
-
Piezoelectric accelerometers offer tremendous versatility for shock and vibration measurements. These rugged sensors can withstand adverse environmental conditions. A wide variety of configurations are available to support multiple application requirements. Specialty units are also available through mechanical or electrical design modifications or additional qualification testing.
-
Product
FD-11613, 8-Channel Temperature Input Device for FieldDAQ
785640-01
Temperature Input Module
8-Channel Temperature Input Device for FieldDAQ - The FD-11613 measures up to eight thermocouple channels. It features cold-junction compensation and open thermocouple detection with an LED indicator per channel to identify disconnected thermocouples. The FD-11613 has an ingress … protection rating up to IP67 (dust- and water-resistant), can operate in -40 °C to 85 °C environments, and can sustain 100 g shock and 10 g vibration. The FD-11613 incorporates Time Sensitive Networking (TSN) and features an integrated network switch and built-in power circuitry for simple daisy chaining. You program the FD-11613 with NI-DAQmx, which automatically synchronizes multiple FieldDAQ™ devices. This device is ideal for test cell and outdoor environments.
-
Product
SDIO- Low Power Radios
-
Its industrial temperature support, robust enterprise security and 802.11ac capabilities make it an ideal solution for applications like factory automation with demanding environmental conditions such as with extreme temperatures, dirt, dust, moisture, shock, and vibrations. Its low power consumption also makes it suitable for portable handheld devices.
-
Product
Vigilant Aircraft Hygrometer
137
-
The Edgetech Instruments Model 137 Vigilant Aircraft Hygrometer is a rugged, shock mounted military qualified instrument used for the primary measurement of dew point in flight or in installations with existing flow, such as wind tunnels.It features a miniature remote dew point sensor employing a platinum resistance thermometer, and has 15 feet of interconnecting cable to the control unit. Precision calibration units for the linear analog outputs are included.
-
Product
Standard Test Finger
SMT-1
-
It with Protection against electric shock device. It according to IEC60335, IEC60884, IEC61032, IEC60529, IEC60065, IEC60035, IEC60950, EN60529, EN60950, GB4706, GB7000, GB9706, UL507, VDE0470, etc.
-
Product
Test Voltage Indicators
PRV240FS
-
Verify your test tool works without unnecessary exposure to shock and arc flash. Make the process easy by using the PRV240FS Proving unit. Verifying that your T6 electrical tester is working properly reduces the need for personal protective equipment (PPE) when a known voltage source is not available for verification before tests are performed.
-
Product
Structural Durability Solutions
-
Instron offers a variety of testing systems and rigs for static, quasi-static and dynamic loading of structures and components. This includes Component Test Systems, Shaking Tables, Road Simulators, Axle Test Systems, Full Vehicle Test Systems, Wheel Test Systems, Shock Absorber Test Systems, Elastomer Test System and Dynamic Torsion Test Systems.
-
Product
Environmental Testing
-
Large Walk-in Environmental Chamber, and Walk-in Salt Fog Chamber, various sizes of vibration and shock equipment, and environmental chambers.
-
Product
Vibration Shaker and Control Amplifier
-
The performance of this Vibration System supports a wide variety of Vibration and Impact Shock capabilities, at g levels and weight-handling levels not previously available at Pacific. Applications include product development, design conformance, qualification, certification, and production screening to Military, Aerospace, Automotive, and Medical specifications.
-
Product
Shock Test Apparatus
-
SCR Elektroniks make Shock test Apparatus is used to test the Electrical accessories / appliances for their mechanical strength. A wooden base fixed to a concrete block and a wooden platform is hinged base. This platform carries a wooden board, which can be fixed at various distance from the hinge and two vertical positions. The end of board bears a metal stop plate, which rests on coiled spring having constant 25N/mm.
-
Product
Micropower, 3-Axis, ±200 g Digital Output, MEMS
ADXL372
-
The ADXL372 is an ultralow power, 3-axis, ±200 g MEMS accelerometer that consumes 22 μA at a 3200 Hz output data rate (ODR). The ADXL372 does not power cycle its front end to achieve its low power operation and therefore does not run the risk of aliasing the output of the sensor. In addition to its ultralow power consumption, the ADXL372 has many features to enable impact detection while providing system level power reduction. The device includes a deep multimode output first in, first out (FIFO), several activity detection modes, and a method for capturing only the peak acceleration of over threshold events. Applications: Impact and shock detection. Asset health assessment. Portable Internet of Things (IoT) edge nodes. Concussion and head trauma detection.
-
Product
Environmental Shock Simulation Machine For Drop Testing
-
# Simulates environmental handling threats small handheld products must survive.# Gauges your product?s ability to survive handling environments.# Controls key test variables: product orientation at impact; nature of the impact surface.# Maintains orientation to just prior to impact then releases for unrestrained impact.# llows user changeable impact surfaces to better simulate the handing environment.# Includes 4 ch short transient shock instrumentation system.
-
Product
Voltage Controlled Oscillators
-
a High Reliability Low Noise Voltage Controlled Oscillator (VCO) which covers a 10 MHz to 20 MHzfrequency band with a voltage tuning range from 0V to 20V. This design features exceptional phase noise performance of -120dBc/Hz @ 10 kHz offset. Supply Voltage is +15V with a generated output power level of +10 dBm and 2nd harmonic output of-11 dBc typical. The assembly is RoHs compliant and available in a compact 0.5 inch SMT package with an industry standardmounting footprint. The bottom surface is copper clad with 2-5 micro inches of immersion Gold over 150 - 250 micro inchesof Electro less Nickel which makes it resistant to oxidation for ease of soldering. The VCO operates over a temperature rangeof -40°C to +85°C and is designed to meet a variety of MIL-STD-202 test conditions including Humidity, Shock, and Vibration.
-
Product
Ionization Anti Static Blower
-
Ionization or anti static blowers are the most versatile ionizer to control or remove static electricity from plastic, paper, glass and other non conductive materials. This static control blower offers the ability to cover a large area cost effectively. This static control equipment is an excellent choice to reduce static electricity and reduce operator static shocks and production applications needing large area coverage.
-
Product
Rugged, High Performance RDE Elemental Analyzer
SpectrOil M Series
-
The latest SpectrOil M series is the eighth generation RDE Optical Emission Spectrometer for elemental analysis in oil and fuel. It is a compact, rugged, transportable and easy to use optical spectrometer that meets military shock and vibration and environmental test standards. The analyzer can be placed in the toughest remote locations around the globe, while still maintaining the laboratory grade accuracy and sensitivity needed for aerospace engine test requirements.
-
Product
Accelerometer
AP2038
-
Combination of high axial sensibility, intrinsic frequency, and shock resistance; Low sensitivity to electromagnetic fields; Feed voltage and current wide range; Low intrinsic noise level.
-
Product
Shock Testers
-
Shock test data is key information when determining if your product is capable of withstanding its intended distribution and use environment. For any mechanical shock testing application, Lansmont builds a Shock Test System to meet your needs.
-
Product
Power Meter
-
OrienTek Optical Technology Ltd.
Power Meter and the Visual Fault Locator.The Optical Power Meter can measure dBm,dB and uW in the wavelength band of 850,1300 1310 1490 1550 and 1625nm.The Visual Fault Locator uses CW mode and Modulation mode and helps to detect the optical cable of up to 10km. Battery performance 50 hours operation,Dust and shock proof design,Auto Shut off function.
