Frequency to Voltage Converters
A device which cleans AC Sinewave signals from an AC source.
-
Product
110 GHz Frequency Extender, Pulsed DC Bias
N5293AX52
Frequency Extender
The Keysight N5293AX52 is a broadband frequency extension module designed for use with Keysight’s new PNA / PNA-X-based millimeter-wave solutions. It is a compact, lightweight, and ruggedize frequency extender module with built-in bias tee for pulsed DC bias operation. It interfaces with the Keysight N5292A test set controller. The modules allow users to extend the frequency coverage of a base PNA / PNA-X Series network analyzers to a range of 10 MHz to 110 GHz. For more information about cable and accessories for use with network analyzers, please visit Network Analyzer Accessories.
-
Product
Transition Time Converter, 500ps
15433B
Transition Time Converter
The new design of these transition time converters ensures very low signal reflection far beyond the 3 dB point, unlike conventional converters. Reducing the signal transition-times also increases the overall pulse-performance for overshoot/reflection sensitive applications. The converters are fitted with SMA connectors, one male, one female. These converters have been designed to convert the fixed transition-times of the Keysight 8133A 3 GHz timing generator (<100 ps transitions) to slower, fixed transition-times (150 ps, 250 ps, 500 ps, 1 ns, 2 ns) hence reducing the signal bandwidth. All transition-times are from 10% to 90% of amplitude.
-
Product
NI-9239, ±10 V, 50 kS/s/ch, 24-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module
779593-01
Voltage Input Module
±10 V, 50 kS/s/ch, 24-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module - The NI‑9239 performs differential analog input. With channel‑to‑channel isolation, your entire system, including the device under test, is protected from harmful voltage spikes up to the isolation rating. In addition to safety, isolation eliminates measurement errors caused by ground loops because the front end of the module is floating. Designed for both speed and accuracy, the NI‑9239 is an effective general-purpose analog module because of its resolution, sample rate, and input range.
-
Product
8 channel 16 bit Digital to Analog
CPCI-DA8-1
Digital / Analog Converter
The CPCI-DA8 is a slave Digital to Analog board that is managed by the host processor on the CPCI bus. The card contains a state machine that performs mostof the work of outputting data, in order to minimize the impact to the HOST system. The CPCI-DA8 is supported by ALPHI Technology under Windows NT by a Board Support Package which is supplied with the card. Other documentationsupplied with the card will describe this support in full detail.
-
Product
NI-9225, 300 Vrms, 50 kS/s/ch, 24-Bit, Simultaneous Input, 3-Channel C Series Voltage Input Module
780159-01
Voltage Input Module
300 Vrms, 50 kS/s/ch, 24-Bit, Simultaneous Input, 3-Channel C Series Voltage Input Module - The NI‑9225 performs differential analog input. The wide measurement range is well suited for high-voltage measurement applications such as power metering, power quality monitoring, motor test, battery stack testing, and fuel cell tests. You can perform transient and harmonic analysis with high-speed simultaneous sampling. In addition, you can prevent ground loops and add safety to a system with 600 Vrms channel‑to‑channel isolation between the three NI‑9225 channels.
-
Product
NI-9263, 100 kS/s/ch Simultaneous, ±10 V, 4-Channel C Series Voltage Output Module
779012-01
Voltage Output Module
100 kS/s/ch Simultaneous, ±10 V, 4-Channel C Series Voltage Output Module - The NI‑9263 is a simultaneously updating analog output module. It features overvoltage protection, short-circuit protection, low crosstalk, fast slew rate, high relative accuracy, and NIST‑traceable calibration. The NI‑9263 module includes a channel‑to‑earth ground double isolation barrier for safety and noise immunity.
-
Product
NI-9220, ±10 V, 100 kS/s/ch, 16-Bit, Simultaneous Input, 16-Channel C Series Voltage Input Module
785188-01
Voltage Input Module
±10 V, 100 kS/s/ch, 16-Bit, Simultaneous Input, 16-Channel C Series Voltage Input Module - The NI‑9220 performs simultaneous differential analog inputs with 250 Vrms CAT II or 60 VDC CAT I isolation. The module is capable of generating 3.2 MB/s of data at the maximum sampling rate. There are two connector options for the NI‑9220: a 36-position spring-terminal connector and a 37‑position D‑SUB connector.
-
Product
NI-9205, ±10 V, 250 kS/s, 16-Bit, 32-Channel C Series Voltage Input Module
785184-01
Voltage Input Module
±10 V, 250 kS/s, 16-Bit, 32-Channel C Series Voltage Input Module - The NI‑9205 performs single-ended or differential analog inputs, with four programmable input ranges for each. It is an effective combination of channel count and speed at a low price for an economical multifunction system. You can choose from four programmable input ranges. To protect against signal transients, the NI‑9205 includes up to 60 V of overvoltage protection between input channels and common. In addition, the NI‑9205 also includes a channel-to-earth ground double isolation barrier for safety, noise immunity, and high common-mode voltage range. It is rated for 1,000 Vrms transient overvoltage protection.
-
Product
60-Watt DC/DC Converter, 3U cPCI
55KQ2-02
DC Converter
NAI’s 55KQ2-02 is a 60 Watt DC/DC Converter that plugs directly into a standard 3U cPCI chassis with a 0.8” slot. It is conduction-cooled through the card edge/wedgelock. This modular, switching power supply accepts +28 VDC input and provides a single output at up to 60 Watts. It is designed to work along with NAI’s 72.5 DC Power Line Conditioner w/Holdup companion unit, model 44KS3-02.
-
Product
120 GHz Frequency Extender
N5295AX51
Frequency Extender
The N5295AX51 modules are compact lightweight modules designed to interface to the N5292A test set controller that is driven with a PNA/PNA-X B model vector network analyzer.
-
Product
sbRIO-9205, Non-Enclosed, ±10 V, 250 kS/s, 16-Bit, 32-Channel C Series Voltage Input Module
784787-01
Voltage Input Module
Non-Enclosed, ±10 V, 250 kS/s, 16-Bit, 32-Channel C Series Voltage Input Module - The sbRIO‑9205 performs single-ended or differential analog inputs, with four programmable input ranges for each. It is an effective combination of channel count and speed at a low price for an economical multifunction system. You can choose from four programmable input ranges. To protect against signal transients, the sbRIO‑9205 includes up to 60 V of overvoltage protection between input channels and common (COM). In addition, the sbRIO‑9205 also includes a channel‑to‑earth ground double isolation barrier for safety, noise immunity, and high common-mode voltage range. It is rated for 1,000 Vrms transient overvoltage protection. Non-enclosed modules are designed for OEM applications.
-
Product
Frequency Converters
-
CAES offers a full range of custom frequency converter solutions including narrowband, wideband and block upconverters and downconverters.
-
Product
synchro or resolver to digital (BCD) converters
AIT
Digital / Synchro Converter
Computer Conversions Corporation
The TSb series are miniature, high performance continuous tracking synchro or resolver to digital (BCD) converters and angle indicators employing a type 2 servo loop, designed for military and industrial control applications. They will accept any 3 wire synchro or 4 wire resolver input over a frequency range of 50 to 1200Hz. and convert it into 0 to 359.9 degrees or +/-179.9 degrees, TTL compatible BCD data.
-
Product
Frequency Converter
A6000-E1
-
The Quartzlock A6000-E1 is a 1U rack mount, frequency converter for use with frequency standards such as rubidium, cesium, or hydrogen maser standards. Sine wave outputs are provided at frequencies of 2,048 kHz
-
Product
Single-Mode Fiber Optic To RS-232/422/485 Converter
ADAM-4542+
Serial-to-Fiber Optic Converter
1 x SC fiber connectorOperation mode: Point-to-Point,Redundant and Ring(half-duplex)Half/Full-duplex, bidirectional transmission modeAutomatic RS-485 data flow controlLED indicator to monitor status
-
-
Product
500 Watt DC/DC Converter, 3U VPX
VPX55H-3
DC Converter
The VPX55H-3 is NAI's latest high power 500 Watt DC/DC converter that accepts a +28 VDC Input and plugs directly into a standard 3U VPX chassis with a VITA 62 0.8” power supply slot. This off-the-shelf solution for VITA 46.0 and VITA 65 systems is compatible with VPX specifications; supports all VITA standard I/O, signals, and features; and conforms to the VITA 62 mechanical and electrical requirements for modular power supplies.
-
Product
725-Watt (270VDC input) DC/DC Converter, SOSA™ Aligned, 3U VPX
VPX57HS
DC Converter
NAI’s VPX57HS-31 is NAI's latest +270 VDC Input, VPX DC/DC Converter. The VPX57HS was developed in alignment of the SOSA™ Technical Standard and is capable of handling up to 725 Watts of output power. It plugs directly into a standard 3U VPX chassis with a VITA 62 1.0” power supply slot. This off-the-shelf solution for VITA 46.0 and VITA 65 systems is compatible with VPX specifications; supports all VITA standard I/O, signals, and features; and conforms to the VITA 62 mechanical and electrical requirements for modular power supplies.
-
Product
Synchro to DC Converters
DC Converter
Computer Conversions Corporation
This unique series of Synchro to DC Converters makes use of advanced digital circuitry techniques to accomplish high speed conversion with extreme accuracy. Transformer isolation as well as balanced line-to-line input impedance is provided for superior and trouble-free system performance, regardless of the input synchro used.
-
Product
Synchro to Digital-Resolver to Digital Converters
SDC-RDC 20
Digital / Synchro Converter
Computer Conversions Corporation
SDC & RDC 20 BIT Synchro / Resolver to Digital Converter
-
Product
Isolated AC Voltage Input Module
ADAM-3112
Voltage Input Module
0 ~ 450 VAC to 0 ~ 5 VDCAC voltage measurement1,000 VDC isolation between output and power2,500 VAC isolation between output and inputInput impendent: 2 MohmMulti input modesAccuracy: ±0.1% FSRFlexible Din-rail mountingOperates from a single +24VDC
-
Product
Digital to Synchro and Digital to Resolver Converters
Digital / Synchro Converter
Computer Conversions Corporation
1.2VA, 1.5VA, 4.5VA and 5VA Models60 or 400, & 60 and 400 Hz. Models to 22 KHz.Trouble Free Isolated Reference Inputs & Signal OutputsUltra High Efficiency, Low DistortionSelf Powered off the AC Reference Input (DSP Series)Internal Cool AC-Pulsating Supplies (DSP Series)Very Low Loss & Heat DissipationFULLY INTEGRATED, NO EXTERNAL COMPONENTS REQUIREDVery High Resistance to Shock and VibrationHigh Reliability Throughout ImplementationIsolated, Transient, Therrnally & Short Circuit Protected Outputs
-
Product
Transition Time Converter, 150ps
15435A
Transition Time Converter
The new design of these transition time converters ensures very low signal reflection far beyond the 3 dB point, unlike conventional converters.Reducing the signal transition-times also increases the overall pulse-performance for overshoot/reflection sensitive applications.The converters are fitted with SMA connectors, one male, one female.
-
Product
725-Watt (28VDC input) DC/DC Converter, SOSA™ Aligned, 3U VPX
VPX55HS
DC Converter
NAI’s VPX55HS-31 is NAI's latest +28 VDC Input, VPX DC/DC Converter. The VPX55HS was developed in alignment of the SOSA™ Technical Standard and is capable of handling up to 725 Watts of output power. It plugs directly into a standard 3U VPX chassis with a VITA 62 1.0” power supply slot. This off-the-shelf solution for VITA 46.0 and VITA 65 systems is compatible with VPX specifications; supports all VITA standard I/O, signals, and features; and conforms to the VITA 62 mechanical and electrical requirements for modular power supplies.
-
Product
RF High Frequency Probes
High Frequency Probe
*Low impedance*High bandwidth up to 20 GHz*Repeatable measurements*Coaxial design*Interchangeable center conductor
-
Product
Airborne Frequency Converter
AFC Series
-
Behlman’s AFC-7000-1 & -2 and AFC-7003, frequency converter are designed to convert three-phase aircraft power to regulated single-phase (115 or 230 VAC) or three-phase (115/200 VAC) at 50 Hz, 60 Hz or 400 Hz. They are ruggedly built to support aircraft takeoffs and landings and designed to meet the input power requirements of MIL-STD-704 and RTCA-DO-160.
-
Product
NI-9221, ±60 V, 800 kS/s, 12-Bit, 8-Channel C Series Voltage Input Module
779373-01
Voltage Input Module
±60 V, 800 kS/s, 12-Bit, 8-Channel C Series Voltage Input Module - The NI‑9221 performs single-ended analog input. The wider voltage range makes this module well suited for industrial-level, automotive, or even smaller-cell battery measurements. There are two connector options for the NI‑9221: a 36‑position spring‑terminal connector and a 37-position D‑SUB connector.
-
Product
Digital to Synchro-Digital to Resolver Converters
ST-DRL ST-DSL ST Prefix
Digital / Synchro Converter
Computer Conversions Corporation
Terminations subject to converter module features where applicable.Plastic backplane mount track included, or may be mounted using spacers at mounting hole locations.
-
Product
75/150-Watt DC/DC Converter w/Holdup, 3U cPCI
75PS4
DC Converter
NAI’s 75PS4 is a DC/DC Converter that plugs directly into a standard 3U cPCI chassis with a 0.8” slot. It is conduction-cooled through the card edge/wedgelock. This programmable, switching power supply accepts a +28 VDC input and is available in either a 75 Watt or 150 Watt-version.
-
Product
Synchro to Digital-Resolver to Digital Converters
MRDC
Digital / Synchro Converter
Computer Conversions Corporation
Computer Conversions’ MRDC64-3 is a miniature single chip solution for providing a complete 1 x 64 speed resolver interface into any demanding industrial or military application.
