-
Product
Battery and Alternator Analyser for 12V DC Systems
1176
-
Checks battery charge level and alternator output level. 880mm of insulated cable with test probe and earth (crocodile) clip. For 12V DC systems only. Display packed.Warning: For testing DC circuits on vehicles within the voltage range only. Not suitable for testing mains supply AC circuits.
-
Product
Car Battery Checker
BT-300
-
Konstar Electric Industrial Co., Ltd
Battery tester can test the car battery whether is ok, if the battery is bad or need charge or bad, the tester will give you the right check result, then can do the right plan for the battery before work.
-
Product
Battery Supervisors
-
DV Power manufactures ideal tools for maintenance, troubleshooting and performance tests on stationary batteries.Capacity testing is performed in order to detect which cells in the string should be replaced by measuring a cell voltage, temperature, inter-cell connection voltage, and specific gravity.IEEE standards for stationary battery applications also stipulate measuring these key parameters during periodic battery inspections.DV Power provides two types of instruments:BVS series – for automated monitoring of battery parametersBVR series – for manual monitoring of battery parametersIn contrast to BVS, BVR instruments can be used for the transfer of electrolyte specific gravity measurements from a density meter (DMA35) via Bluetooth. This provides a more extensive analysis of each cell in the tested battery string.
-
Product
PXI/PXIe Battery Simulator Module, 2-Channel, 750 V Isolation
43-752A-003
Battery Simulator
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 2-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
Product
Automotive Battery Tester
-
Automotive battery tester, detection of battery power status; may be used as USB car charger.
-
Product
Advanced Battery Tester
DBT-12+
-
The tester enables safe measurement of voltage, current rating, state of charge and state of health for 12V and 6V batteries. The device is powered by an internal battery, so it can test even discharged batteries and can be conveniently used as a voltmeter.
-
Product
Battery Emulator And Profiler
E36731A
Battery Simulator
The Keysight E36731A battery emulator and profiler is an integrated electronic load and power supply developed to use with Keysight PathWave BenchVue battery emulation software. An emulated battery gives you a known good reference for testing at any charge level. Quickly assess the effect of design or software changes on battery life by emulating any battery charge state. Leverage emulation and precise current drain analysis to achieve longer battery life or to reduce the size of your device.
-
-
Product
Battery Test and Analysis System
BTAS-16
-
The task of testing an aircraft’s Nickel-Cadmium batteries is complicated and involved because of the high number of cell voltage readings that need to be taken during testing. Taking voltage readings from all 20 cells in the typical nickle-cadmium aviation battery multiple times is laborious and error prone, but must be done to properly estimate the condition of the battery under test.
-
Product
Parallel Differential Battery Tester With Integrated Chamber
-
Accelerate your battery parallel test using our PDBT. Featuring an integrated chamber, it precisely conducts battery comparison test and fast measures battery's self-discharge current. Its portable, powerful design is perfect for innovative research applications.
-
Product
PXI/PXIe Battery Simulator Module, 4-Channel, Simplified Current Sink, 750 V Isolation
41-752A-902
Battery Simulator
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 4-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
Product
Mixed Signal Battery Test System
Test System
The Mixed-Signal Battery-Test System is an automated test platform designed to meet today’s advanced battery test requirements. The platform is ideal for testing a range of battery cells and packs, and can be used in applications such as research and design, quality control, and end-of-line manufacturing. Its distributed architecture provides a scalable solution with configurable system components to accommodate specific applications.
-
Product
Battery Management LEM BMS Software
CELLooK
-
LEM is the latest and most advanced Battery Cell Monitoring System. The CELLLook is the web-based Software that could monitor, diagnose and analyze the Battery cell capability by an internet access. (Developed DB engine in Korea and registered a trade mark). The auto alarm, diagnostic and analyzing software for all Microguard data that Jaeshininfomation Co., Ltd with Web2.0 solution.
-
Product
Counter Battery
-
This all fuels the need to redefine effective approaches in counter battery, in particular for the functions usually fulfilled by weapon location radars: target acquisition, fire control and prediction of impacts.
-
Product
Pet-Gard Electric Fence Charger
PG-50
-
Parker McCrory Manufacturing Co.
A small 110-120 volt A.C. electric fencer unit to protect your garden, flower beds, or shrubs from small animal damage. This fencer delivers a safe uninterrupted voltage with very low current to comply with the national electric safety code. Not recommended for livestock.
-
Product
CYCLOPS Battery Powered Headlamps
CY3-LED
-
*LED light mounts on hard hat and allows quick and efficient hands-free movement*Allows for even distribution of weight across the forehead*Water-resistant*Field replaceable batteries
-
Product
Development Platform for Battery Operated IoT Applications
Thunderboard Sense
-
Thunderboard Sense is a small and feature packed development platform for battery operated IoT applications. The mobile app enables a quick proof of concept of cloud connected sensors. The multi-protocol radio combined with a broad selection of on-board sensors, make the Thunderboard Sense an excellent platform to develop and prototype a wide range of battery powered IoT applications.
-
Product
Battery Management Controllers
-
Renesas offers a dedicated single-package solution with an MCU and analog front end (AFE) for battery management systems that constantly monitors the battery state.
-
Product
Battery Testers
-
Shanghai Beha Electronics Co., Ltd.
*can measure the resistance of rechargeable batteries and DC voltage.*can also test Ni-cd, Ni-MH, Li-ion batteries.*DC Voltage measurement.*4-wire resistance measurement.
-
Product
Electric Vehicle Charger Testing
EV-TEST100
-
EV-TEST100 in combination with appropriate HT multifunction instrument simulates an electric vehicle connected to the charging station, allowing you to verify the EVSE full functionality and electrical safety. EV-TEST100 is able to test charging stations with charging modes 2 and 3 and Type 2 connector (European standard).
-
Product
Battery Charge And Discharge Test System
9841
-
*Easy user interface*Measure Voltage, Current, Power, KWH, AH, Temperature, Reference Voltage*Accuracy Measure Time*Easy to see now test progress*Can cycle test*Provide Charge, Discharge, Suspend, FOR, LOOP Mode Select*When Charging, set the stop current to stop charging when fully charged so as to avoid overcharging that will damage the battery. When Discharge, set the stop voltage to stop discharge when discharging to lowest so as to avoid over-discharging that will damage the battery. *The test result will be stored to ACCESS data
-
Product
Battery Capacity Tester
BLU-C Series
-
BLU-C is the latest solution from DV Power for conducting a comprehensive battery capacity test. This universal instrument is applicable to any battery string, such as lead-acid, Li-Ion, Ni-Cd, and others, with voltages up to 800 V DC.BLU-C tester simplifies battery testing in multiple ways. The instrument provides monitoring of discharge parameters (graphically and numerically) in real-time on a 7-inch touch screen display. The instrument also enables measurement and monitoring of cell parameters (voltage/intercell voltage/temperature), which makes it a complete stand-alone discharge test system.The capacity tester is compatible with DV-B Win software. Because of that, the user can view detailed numerical and graphical presentations of key parameters, and create reports in various formats.The capacity test is performed in a user-friendly way according to battery testing standards: IEEE 450-2010, IEEE 1188-2005, IEEE 1106-2015, IEC 60896-11/22 and other.The battery tester enables setting the discharge current up to 300 A, with 0,1 A resolution. If higher currents are required, BLU-C units can be connected in parallel, or BXL additional load units can be used.The user can select one of three discharge modes: Constant current, Constant power, Constant resistance. Additionally, different battery duty cycles can be simulated using user-selectable discharge profiles.Testing can be carried out without disconnecting the battery from the equipment it supplies.
-
Product
Low Voltage DC / Battery Powered HV Amplifiers
WMA-02 And WMA-02LF
-
The Falco Systems WMA-02 is a high voltage amplifier that runs from an 24 - 30V DC power supply and can be battery powered if required, e.g. for use in a Faraday cage. Its internal high voltage generator is inductor-free and hence does not spread magnetic interference in sensitive experimental setups. The output noise is impressively low at 4mVrms. For extremely low noise applications where bandwidth is not an issue, a dedicated WMA-02LF version is available that contains an output low pass filter capacitor which reduces the bandwidth to 50Hz, but makes the noise drop to below 0.2mVrms. This bandwidth-limited amplifier is ideal for MEMS or piezo positioning with manual voltage adjustment.
-
Product
Continuity Tester Supplied without Battery
22700
-
Use to test for continuity with power disconnected. Excellent for use on marine, recreational and general automotive vehicles. Test appliances and other electrical circuits with power off. 48" lead wire. Uses AA 1.5 volt battery (not supplied).
-
Product
Battery Testing Equipment
-
Mainly for battery testing in lab,such as 5V1mA, 5V10mA, 5V50mA,5V100mA, 5V1A,5V3A,5V6A,5V10A
-
Product
Battery Capacity Testers|Discharge Testers
-
DV Power offers a wide range of battery capacity testers to meet specific customer needs. All of them are portable, powerful and most of all universal. Any battery string, such as lead-acid, lithium-ion, nickel-cadmium based and others, with voltages in the range of 0,9 – 800 V DC can be tested in an accurate, user-friendly way.The capacity test is carried out following the battery testing standards: IEEE 450-2010, IEEE 1188-2005, IEEE 1106-2015, IEC 60896-11/22, and other relevant standards.BLU battery testers enable setting the discharge current up to 350 A, with 0,1 A resolution. If higher currents are required, several units can be connected in parallel, or BXL additional load units can be used. Discharge parameters can be monitored in real-time during the capacity test. Overall battery voltage, current, elapsed test time and capacity will be presented during the entire test on a touch screen display.
-
Product
Hybrid Vehicle Battery Simulator and Test System
-
Winner of the SAE 2008 Technical Award for Hybrid Vehicle Testing Technology, SAKOR Technologies Hybrid Vehicle Battery Simulator and Test System is designed for simulating high-voltage batteries in an electric drivetrain testing environment as well as directly testing high-voltage batteries and charging systems.
-
Product
Durable Hand-Held Battery Tester
6029
-
• Test 6 & 12 Volt batteries, alternators and starters• 125 Amp fixed load• Made in USA of US and Global Components
-
Product
Battery Temperature Test Chamber
-
Sanwood Environmental Chambers Co ., Ltd.
Sanwood climatic chambers for battery can be tested under controlled temperature and humidity conditions, similar to the conditions under which batteries operate during their lifetime.
-
Product
Battery Impedance Tester
-
TES Electrical Electronic Corp.
Test conditions without shutting down battery.Simultaneously measures battery resistance, Voltage, current, and temperature.Auto-hold and auto-data storage. Comparator Function.Rates conditions as pass, warning, or fail.
