Bare board Fixtures
accurately position and retain unloaded PCBs.
See Also: Bare Board Testers, Board Test Fixtures, Bare Board
-
product
Universal Test Fixture
Series 48
The Series 48 Universal Test Fixture Systems are an effective way to test high mix, low to medium volume products. The Universal Base is designed around the CAMGATE Z axis Test Fixture. The base interfaces with removable, quick change Series 49 Universal Test Insert Kits. Three versions are offered, a blank base whereas the end user can configure the Base and insert kit to their own connector configuration, The 160 point model which uses four (40) pin IDC ribbon cable connectors to interface between the base and the insert kit, and the -I model that incorporates the same 4 block GR2270 style block interface as used on our Series 34 test fixtures. This allows for increased test point count and the use of Industry Standard 2270 style signal, power, and coax blocks. Rear panels can be custom configured to customer specifications, Virginia Panel ITA frames, or GR2270 Interfaces used on Semco’s Standard Product line
-
product
Single Board Computers
SBC35-CC405-3845
Industrial embedded computer with Quad-Core Intel® Atom™ E3845 CPU, Dual Ethernet, Dual MiniPCIe, USB 3.0, RS-232/485/422 and two independent displays via DisplayPort, LVDS and/or Analog VGA.
-
product
COM Express Boards
COM Express is a highly integrated Computer On Module. It can be considered as a component (integrated circuit) in more complex designs.
-
product
CompactPCI Boards
*CompactPCI (cPCI) boards are 3U or 6U boards connected via a passive PCI (Peripheral Component Interconnect). Up to 8 boards can be connected together in a segment. Segments can be connected through bridges. *They are grouped into four categories: CPU, Communication, Input/Output, PMC carrier.
-
product
PCI Evaluation Board
BCM91250E
The BCM91250E is a full-length PCI evaluation board with the SiByte® BCM1250 dual-processor System on a Chip. The board is designed for software development and for developing PCI applications that require high-performance processors.
-
product
ARINC HSI / ADI Test Fixture
TA-2000
The TA-2000 test fixture is a combination panel that incorporates all the standard capabilities of the legacy CTS-11(ADI) and CTS-12(HSI) panels and much more. This panel is married to our model TA-1001 dual synchro transmitter/API panel thus allowing for local stimulus and alignment of the instruments synchros and resolvers. The panel provides for testing of both superflag(28v) and low level meters through a matrix of switching that will allow testing of all meters simultaneously or just individually. The low level meter drive circuit also incorporates an automatic mode that will continuously oscillate the L/R and Up/Dn pointers.
-
product
Carrier Boards
Advantech Development boards provide a schematic software & reference design to reduce efforts needed in development stage. Advantech Development Board can be used to test carrier board problems and support COM series, and Qseven, ETX / XTX form factors.
-
product
ICT Test Fixture
It can be produced in our overseas branches which are Thailand ,China and India.High precision test fixture can be produced.Test fixture for other brand testers can be produced.
-
product
Headphone Test Fixture
AEC206
The Larson Davis Model AEC206 Binaural Test Fixture is the tool for testing supra-aural, circumaural, supra-concha, intraconcha, and insert-type headphones. Preassembled with IEC 60318-4 (711) occluded-ear simulators and TEDS compatible preamplifiers that provide electronic calibration information, the Model AEC206 is user-friendly and easy to learn. Additionally, calibration is a simple process—a custom adapter is included for the Model CAL250 acoustic calibrator or similar device.
-
product
Load Board
cPCI 3U
Load boards are essential in keeping any system in top running shape. As a full-system provider, Hartmann strives to not only provide the systems you need, but the supporting hardware as well.
-
product
In-Circuit Test Fixture Design Services
An integral part of board test is the test fixture. Innovations in board technology may manifest themselves as challenges in test fixture design. Utilizing a creative & systematic design philosophy, Acculogic consistently delivers state of the art solutions for the most complex test interface problems.
-
product
Manual Fixture Kit
230376 – CMCSK-07-01
Linear click system with ball bearings, using gas springs.10 mm ESD-proof top cover with aluminum reinforcement bars.Steel base cabinet with detachable aluminum back and bottom panels.Detachable interchangeable case system with an 8 mm spring-loaded probe protection cover.Base cabinet fitted with a telescopic guide rail and catch.
-
product
Emergency Battery Test Fixture
TA-60
This test fixture will allow servicing of the 60-1321-( ) series of emergency exit light power supply. These supplies are used in many aircraft to annunciate exit lighting when aircraft power failure occurs. The TA-60 test fixture is equivalent to the suggested test fixture in the OEM 60-1321 CMM. The four load lamps are conveniently placed behind an acrylic red lens for proper viewing while performing load test. The bench cable is provided as part of the test fixture.
-
product
3.5-inch Embedded Board
The 3.5" embedded board is created in an architecture of low power consumption with reliability required for various applications in rugged environments. The ZIO form factor is an integrated interface standard defined by Axiomtek and has been adopted as one of our specifications in our 3.5" embedded single board computers to meet concerns regarding insufficient expansion interfaces in small form factor (SFF) single board computers.
-
product
Stand-Alone Test Fixture
MA 2012/D/H/VPC-G12x-18
Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: NoInterface signals max.: 1190Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 17,50 kg
-
product
Clamshell Type Mechanical Fixtures
Known in the ATE Industry as “Clamshell” type Test Fixtures, Semco’s Mechanical Test Fixture line is a cost-effective solution to test Printed Circuit Boards and Assemblies. This Test Fixture line is also available with the most widely used interfaces in the test industry.
-
product
Development Boards
Everything From Full-Featured to Tiny Starter Boards. Professional, full-featured development platforms, rich in modules. Each Easy Board features on-board programmer or debugger, and supports an entire family range of microcontrollers.
-
product
Test Extension Boards
XJIO
The XJIO boards are expansion units that enable you to improve the test coverage for a Unit Under Test (UUT) by verifying the signals right through to the external connections. They will integrate with your XJTAG test system to provide access to otherwise inaccessible areas of your circuit. With a range of digital and analogue I/O pins on the board, you can improve fault isolation, verify power rail levels, and dispense with costly custom test jigs - even for non-JTAG boards.
-
product
Motion Control Board, PCI
APCI-8001-1
*Axis control for 1 servo or stepper motor*Onboard processor*Optical isolation*16-bit analog output channels*Direct connection of commercially available incremental encoders *or SSI absolute encoders
-
product
Flexible Pitch GND Fixture Clamps
GF-A
High Power Pulse Instruments GmbH
*Compatible with GGB picoprobe model 10 replacement probe tips*<1 ns rise time (200 ps possible with 5 mm GND wire length)*Custom selectable GND wire length 5-15 mm*Gold-coated spring-steel clamp with micro-machined groove for locking of the clamps on the probe tip*High conductivity and low inductance copper HF litz wire with 200 x Ø 0.02 mm strands*Easy to use clamping*Tungsten carbide probe needle with 1 inch length, 15° taper and 7.5 µm tip radius
-
product
PC/104 OneBank Board
EMC2-SoM3-300
Sundance Multiprocessor Technology Ltd.
The PCIe/104 OneBank™ design enables the EMC²-SoM3-300 to be added to robust and rugged installations for various commercial, medical, industrial and military uses and to enable more versatility the EMC²-SoM3-300 also incorporates a VITA57.1 FMC™ LPC connector opening up an range of extra possibilities and expansion options.
-
product
FMC-HPC ADC Board
FMC121
Sundance Multiprocessor Technology Ltd.
The FMC121 provides two 16-bit A/D channels up to 1Gsps and two 16-bit D/A channels up to 1.4 Gsps data rate with a 2.8 GSPS update rate. The design is based on Texas Instruments’ ADS54J60 Analog-to-Digital converter and Texas Instruments DAC39J84 Digital-to-Analog converter. The sample clock can be supplied externally through a coaxial connection or supplied by an internal clock source (optionally locked to an external reference) for multi-channel synchronization. An external trigger input is available for timing synchronization. The FMC121 is mechanically and electrically compliant to the FMC standard (ANSI/VITA 57.1).
-
product
PCIe Carrier Board for SOM3
Solar Express 215 (SE215)
Sundance Multiprocessor Technology Ltd.
SE215 is a development board for Sundance SOM3 . It is a PCIe X1 Gen2 carrier card with one site for an SOM3. It offers USB JTAG and UART, through a micro USB connector, Display port and comes with a version of Display port IP core for SOM3 from Bitec DSP. The card provides Power GOOD and user LEDs for rapid debugging.
-
product
Exchangeable Test Fixture
MA 2112/D/H/S-7/GR2270/71
Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: Test system sideInterface signals max.: 1190Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 12,13 kg
-
product
FPGA DSP Board
Renice has developed part of the FPGA evaluation board, which can be used as high-speed signal processing board, wireless communication board and image processing board. By default, it’s equipped with Altera FPGA (StratixIV), high-speed ADC/DAC, USB Controller and SODIMM Connector.
-
product
Performance Board
The role of the performance board is accurate transmission of tester signals all the way to the device leads. Custom performance boards from ADVANTEST deliver support for DUTs (devices under test), as they become faster and smaller, with greater pin counts, and increasingly take the form of SMDs. ADVANTEST performance boards also support a host of test requirements, such as analog test, high-speed performance, and high-density, for testing state-of-the-art ICs.
-
product
Analog I/O Board
VME-3128A
The VME-3128A scans 16, 32, 48 or 64 channels, continually digitizes all of them and stores the results. Choose from 64 differential or single-ended inputs and program VMEbus interrupts and interval timer to meet the unique requirements of your mission.
-
product
Functional Test Fixtures
RNS can build almost any test equipment and automated test machinery. We have delivered soltions for HiPot, LED Test, Leak Test and RF shielded applications for years. We can provide Complete Test Systems, including Test Fixtures, Rack System and even Programming. Our team is committed and has a proven track record of delivering exceptional products independent of scope, so simple- and high-complexity projects are handled with equal care.
-
product
Single Board Computer
VME-183
Curtiss-Wright Defense Solutions
AltiVec technology, and up to 1 GB of DDR1 SDRAM, the VME-183 Single Board Computer provides an ideal platform for general purpose computing.
-
product
Digital Interface Boards
Model 2363 OEM
* 114515 Board has same digital capability as the 2363 described above with Serial and GPIB IO.* Serial interface header includes RS-232 and RS-485 signals. Use the 114597 Serial Cable Kit to connect the serial signals to your rear panel* GPIB header mates with 113640 or 113642 GPIB Connector/Address Switch Cable Assemblies* Accepts 9-32 Vdc power.
