PMC Modules
-
product
PMC Modules
ARINC 429
Sycos range of ARINC 429 PMC modules offer the user up to 32 channels on a single width PMC module. Each channel can be programmed independently to operate at either high or low speed. Firmware options available for Tx Error Insertion and Rx Error Reporting are available.
-
product
MIL-STD-1553 A / B Test And Simulation PMC Module
PMC-1553
*Dual redundant*1, 2 or 4 channels*Simultaneous bus controller, 31 remote terminals, bus monitor*Error entry and detection*FPGA based hardware architecture*Multi-level trigger for data acquisition and filtering*10 programmable, discrete I / O (up to 30V)*IRIG-B timecode encoder / decoder with free-running mode*Real-time recording and physical bus playback*Supports: C, C ++, C # and .net*Driver support: Windows, Linux, LabView Real-Time and other systems*Heat sink and / or protective coating available*Optional input / output for front panel
-
product
PMC Module
PMC-CIV-32LVDS
User Programmable AlteraCyclone IV FPGA 484 BGA:EP4CE30, EP4CE50,EP4CE70 options• Stand alone possibility• Single wide PMC Module• Optional User clock oscillator
-
product
6U VME Carrier for PMCs and PrPMCs
Ti4400
The Ti4400 is a 6U PMC/PrPMC carrier for VME systems and forms the basis of a flexible I/O system. The user can integrate two single PMC modules or one double-wide PMC.
-
product
Digital I/O
Curtiss-Wright Defense Solutions
Our digital I/O cards include interfaces to LVDS, Camera Link, Serial interfaces, and customizable I/O. Built leveraging our decades of experience producing highly rugged COTS signal acquisition hardware, our PMC and XMC modules are designed to perform reliably in the toughest operating environments.
-
product
PMC Carrier Card
APC-PMC
This board provides an easy and low cost solution that enables use of a PMC mezzanine I/O module in a standard PCI computer system. The carrier card acts simply as an adapter to route PCI bus signals to and from the PMC module through the PCI card slot edge connector.
-
product
VME Generic Carrier Card For Conduction Cooled PMC(PCIbus Mezzanine Card) Modules
AVC-2-CC
VME64x (6U) generic carrier card for conduction cooled PMC (PCIbus mezzanine card) with 2 PMC slots. Modular solution combines any AIM conduction cooled PMC module for ARINC429, MIL-STD-1553 or any conduction cooled 3rd party PMC module.
-
product
6U Form Factor PMC/PrPMC Carrier-VMEbus
i4400
The i4400 is a low-cost 6U form factor PMC / PrPMC carrier for the VMEbus and forms the basis of a flexible I/O system. It offers the user a means of integrating two single PMC modules or one double PMC module in a VMEbus system. The current version of the i4400 supports PMC modules and also supports Processor PMC modules on one PMC-site. The VME-to-PCI bridge is implemented in an FPGA for flexible VME-to-PCI mapping and to allow future updates and upgrades.
-
product
VME Generic Carrier Card For PMC(PCIbus Mezzanine Card) Modules
AVC-2
VME64x (6U) generic carrier card for PMC (PCIbus mezzanine card) with 2 PMC slots. Modular solution combines any AIM PMC module for AFDX®/ARINC664P7, ARINC429, MIL-STD-1553 or any standard 3rd party PMC module.
-
product
Socket Saver
4690
The Technobox PMC Socket-Saver permits cost effective volume testing of PMC modules when used with Technobox P/N 3390 ?PMC to PCI adapter for Test.? It may also be used to reduce wear and tear on Technobox P/N 1518/1523 (?Extender/Preprocessor?).
-
product
PMC-to-PCI Express Adapter
4733
The Technobox, Inc. P/N 4733 PMC-to-PCI Express Adapter permits the use of a single-wide PMC module in a 4X PCIe slot. The product features a PEX8114 bridge running in transparent mode. The A and C rows of a 96-pin DIN connector connect with the 64-pin user I/O connector (J4/P4) on the mezzanine card. 64-bit support.
-
product
Mezzanine Module
RS485-MOD2
Curtiss-Wright Defense Solutions
The RS485-MOD2 is a front panel mezzanine module designed to provide serial I/O functionality to Curtiss-Wright FPGA-based processing PMC and XMC modules including the PMC-FPGA03, PMC-FPGA05 and XMC-FPGA05D. This RS485 I/O module provides 33 channels of EIA-485 or EIA-422B serial I/O. Each channel is configured as an input or output. The serial protocol and timing are handled by the host FPGA.
-
product
MultifunctionAsync Serial Communications Adapter
2628
The Multifunction RS422/RS485/Digital I/O board provides a collection of various interfaces on a single-wide PMC module. The two 16550 UARTs on the board provide asynchronous communication at bit rates to 115Kbaud. The 16550?s are mapped into host processor space so that standard drivers can be used with the board.
-
product
Mezzanine Cards
PMC and XMC are the quasi standard for mezzanine cards in VME systems. esd's PMC and XMC modules extend your system with a bus interface (CAN, EtherCAT, Ethernet) or an intelligent sub system (e.g. XMC-CPU/2041, PMC-CPU/440). Furthermore esd develops customized PMC and XMC modules. VME systems without PMC slot can be extended with an esd VME-PMC-Caddy or PCIe-XPIMC-Carrier board.
-
product
PMC Module
XMC-603
Curtiss-Wright Defense Solutions
The XMC-603 PMC module allows customers to readily incorporate MIL-STD-1553 into military and aerospace embedded computing systems. As one of several products in our comprehensive range of rugged XMC modules, the XMC-603 integrates well with other elements of our product line, featuring technical support, lifecycle management services, and assured long-term availability.
-
product
PCIe Carrier For PMC And PrPMC
PCI104
The PCI104 is a PCIe carrier for PCI Mezzanine Cards (PMC) or Processor PCI Mezzanine Cards (PrPMC). The PCI104 carrier allows simplified testing of PMC/PrPMCs and their associated PMC I/O Modules (PIMs) by using a PC environment during board development or deployment. The PCI104 can also reduce the costs of manufacturing PMC/PrPMCs by allowing manufacturers to use off-the-shelf PCs for functional testing. The PCI104 converts the PCIe x4 edge connection to PCI-X via a PCIe to PCI-X bridge. The trace lengths to the PMC/PrPMCare kept to a minimum so the PMC/PrPMC can run with a133MHz PCI-X clock speed. The J4 connector of the installed PMC/PrPMC is routed to a 96-pin DIN connector per theVITA-35 specification. The PCIe to PCI-X bridge can run in either transparent or non-transparent mode and can also operate in forward or reverse mode. The PCI104 has a fan mounted on the board to cool the PMC/PrPMC. The fan can easily be removed for testing and probing of hosted card.
-
product
Expansion Adapter Chassis
TB3-TO-CMC-LP
The TB3-TO-CMC-LP is an expansion adapter chassis using the Intel Thunderbolt 3 interface. The adapter allows the use of a front I/O XMC or PMC card outside its normal confines of a single board computer (SBC) or PC hosted carrier card. The TB3-TO-CMC-LP enables the deployment of XMC or PMC modules in systems previously unable to host them -- laptops, small form factor PCs, and other computers lacking add-in slots.
-
product
PCI-Express Generic Carrier Card
ACPe-1
PCI-Express generic carrier card for PMC (PCIbus mezzanine card) modules with 1 PMC slot. Modular solution combines any AIM PMC module for AFDX®/ARINC664P7, ARINC429, MIL-STD-1553 or any standard 3rd party PMC module.
-
product
AFDX ® / ARINC 664 Test And Simulation PMC Module
PMC-664
*Supports IEEE 802.3 10/100/1000 Mbit / s full duplex Ethernet connections*Uses SFPs to support both electrical and optical interfaces*Half-size PCI / PCI-X modules*Simulates multiple AFDX® / ARINC 664 end systems*Standard Ethernet processes simultaneous to AFDX® / ARINC 664*Up to 128 output VLs and 512 input VLs*Upper layer protocol handling (ARINC 653, UDP, IP) managed onboard*DMA for high data rate applications*Windows XP / 7, Linux, and LabVIEW Real Time Drivers & APIs (others on request)Easy to use tool for configuring A*FDX® / ARINC 664 end systems (XML based)
-
product
PMC Module
PMC-1553-PLX
Operating temperatureCommercial: 0 to +70 °COptional: -40°C to +80°C• Airflow requirement: .5 CFM• Humidity: 5 to 90% (non-cond.)• Altitude: 0 to 20’000 ft
-
product
Interface
RCNIC-A2PA3
The RCNIC platform is a high performance, 3U CompactPCI module (PMC on carrier card) for the AFDX/ARINC 664 protocol. With two independent ports for traffic monitoring, traffic generation, external triggering and analysis, the RCNIC provides high-resolution time-tagging of incoming packets simultaneously with highly accurate traffic generation. An IRIG-B receiver/generator is included for synchronization to an external IRIG-B time source and for synchronization between multiple RCNIC boards.
-
product
ARINC825 Cards
AIM’s ARINC825 cards can work either with full functionality as an active CAN node for testing and simulating or in listening only mode for monitoring and recording purposes of Avionic CAN bus (ARINC825) applications on up to 4 electrically isolated CAN bus nodes concurrently. All nodes are in conformance with the ISO11898-1/-2 standard. They are accessible by software separately and can be used as 4 independent CAN bus nodes. An onboard IRIG-B time decoder allows users to accurately synchronize single or multiple modules to a common time source. All supported signals are available through front I/O and rear I/O interface. ARINC825 cards consist of FPGA based CAN interface controllers as well as a FPGA based 32-bit microcontroller core and a separate processor for IRIG-B synchronization with high resolution time stamping. All nodes are operating concurrently at CAN bus high speed bit rate of up to 1Mbit/s with the intelligence to process scheduling of CAN frames in real time onboard to significantly off-load the host processor.For embedded applications the AMC825-4 PMC module is available in a conduction cooled version. Using AIM’s family of PCI, CPCI (3U and 6U) and VMEbus carrier cards for PMC our clients have off the shelf solutions in a broad range of card formats. ARINC825 (CAN bus) modules are delivered with an Application Programming Interface (API) and Driver Software compatible with Windows, Linux and VxWorks.An ARINC825 Resource Component is available for AIM’s PBA.pro™ databus test and analysis tool including Tx and Rx simulation capabilities, a Chronological Bus Monitor and support for decoding of payload data within CAN messages. This allows to implement a powerful ARINC825 (CAN bus) analyzer or a complete test system in conjunction with other AIM avionics databus interfaces and PBA.pro™ supported 3rd party hardware.
-
product
Interface
RCNIC-A2PA
The RCNIC platform is a high performance PMC module for the AFDX/ARINC 664 protocol. With two independent ports for traffic monitoring, traffic generation, external triggering and analysis, the RCNIC provides high-resolution time-tagging of incoming packets simultaneously with highly accurate traffic generation.
-
product
PMC Products
Our PMC modules are based on technology and circuit designs with time-tested reliability in thousands of installations. Great effort goes into selecting high-performance parts to withstand the demands of military, aerospace, and manufacturing applications. Most models are available with extended temperature ranges for reliable operation in harsh environments. Acromag products are also designed for the long lifecycles required for OEM and defense projects.
-
product
32x ADC, 16x/0x DAC & 8x Digital I/O PMC Module
TPMC533
The TPMC533 is a standard single-wide PCI Mezzanine Card (PMC) compatible module providing 32 channels of simultaneous sampling true differential bipolar 16bit analog input, 16 or no channels of simultaneous update single-ended unipolar/bipolar 16bit analog output and 8 channels of tri-state 5V-tolerant TTL digital input/output. All signals are accessible through a HDRA100 type front I/O connector.
-
product
CompactPCI (3U) Generic Carrier Card For PMC(PCIbus Mezzanine Card) Modules
ACC-1
cPCI (3U) generic carrier card for PMC (PCIbus mezzanine card) with 1 PMC slot. Modular solution combines any AIM PMC module for AFDX®/ARINC664P7, ARINC429, MIL-STD-1553 or any standard 3rd party PMC module.
-
product
PMC Module
PMC-DA816
The PMC-DA816 is a slave Digital to Analog boardthat is managed by the host processor on the PMCbus. The card contains a state machine that performsmost of the work of outputting data, in order tominimize the impact to the HOST system.The PMC-DA816 is supported by ALPHI Technologyunder Windows NT by a Board Support Packagewhich is supplied with the card. Other documentationsupplied with the card will describe this support in fulldetail.
-
product
CompactPCI Peripheral Cards
ADLINK provides CompactPCI Peripherals including PMC Modules and Power Supplies.
-
product
PMC-to-PCI Express Adapter
4749
Our PMC-to-PCI Express Adapter 1X (64-Bit) (4749) permits the use of a single-wide PMC module in a 1X PCIe slot. The product features a PEX8114 bridge running in transparent mode.
-
product
CompactPCI
3U PMC Carrier
This conduction cooled 3U CompactPCI single slot PMC provides an active interface between the CompactPCI bus (backplane) and a PCI Mezzanine Card (PMC). This product addresses the needs of aerospace, military, and rugged applications. It contains a thermal heat frame made of aluminum that fits together with conduction cooled PMC modules. Conduction cooling conducts heat away from the hot spots of the board and transfers the heat to the card edges and to the system chassis. No active ventilation is necessary inside of the system, which means the boards are sealed from the environmental influences found outside of the chassis. The heat frame and integrated wedge locks for the conduction cooling stiffens carrier and PMC module enabling the board to resist high shock and vibration.
