Filter Results By:
Products
Applications
Manufacturers
Comparators
Contrast similar or divergent values.
-
product
32 Channel Analog Comparator Module
DP-VXI-5106
DP-VXI-5106, is a 32 Channel Analog Comparator Module with 32 channels of differential analog window comparators. Each channel is provided with a window comparator as well as a Level Comparator , software selectable on an independent channel basis. All the 32 channels have been grouped into four groups of 8 channels each. This allows the user to configure the comparator module based on the application to initiate alarm action to exactly meet application requirements. Each Comparator channel can be programmed to generate a VXI bus interrupt or can be masked through software. An Interrupt is generated on an individual channel basis or on a group basis. Front panel outputs of buffered TTL and a 2-CO relay contact is available for every group (4 outputs total each). Also, a common buffered TTL interrupt output and a common 2-CO relay contact is also available at the facia providing extensive flexibility in application engineering.This module is an ideal device for GO / NO-GO testing in Test Stand Automation where important signals must be continuously monitored for system shut down purposes and safety inter-lock implementation. The hardware implementation in the Comparator module provides high-speed throughput and reliable inter-lock implementation. The interrupt out signal can be further wired as trigger signals for pre and post trigger analysis of signal data for post acquisition detailing.Each channel provides a Window Comparator implementation and a Level Comparator implementation. The configuration is programmable through software and the alarm can be generated if the signal is within the window or outside the window. Similarly, a high and low limit can be set and a trigger is generated if the signal exceeds the high limit or drops below the low limit.
-
product
L-Band Separate Raman Fiber Amplifier
RFA6000
Hangzhou Huatai Optic Tech. Co., Ltd.
1. Erbium-doped Fiber Amplifier, due to the multiple cascades and the accumulation of noise caused by spontaneous emission, will reduce the system CNR greatly and thus it will limit the transmission capacity and distance of the system. Raman Fiber Amplifier (RFA) is a newly designed fiber amplifier based on Stimulated Raman Scattering (SRS) effect. It is considered as the core technology of new generation DWDM fiber over-long communication. Compared with Erbium-Doped Fiber Amplifier, Raman amplifier has the advantage of low Noise Figure (NF), wider gain bandwidth, flexible gain spectral region and stable temperature. It is the only device that can operate in 1300~1600 nm.
-
product
High Current Comparators And Power Supplies
Designed in 3D, this custom unit fills the gap between the comparator manufacturers and the production floor. Vidac Solutions does not manufacture CT Comparators, but this unit (and others like it) are used to provide the complex high-current switching, buss-work, source current supply into an enclosure that fits into the production line and provides a safe, ergonomic and easy to use machine for the operators.
-
product
High Performance Chipscale Test Sockets
SC
Ardent Concepts Test Sockets for ATE test deploy patented SC Contact Sets. This technology is capable of over 2 Million mechanical insertions in production environments and uses easy to replace pins with no complicated assembly procedure. It is designed to be drop-in compatible with 1mm offset and straight through footprints to ease implementation, and RC SC’s simple and robust design is extremely cost effective when compared with existing “roll” type test contactors and sockets. Designed specifically for JEDEC QFN and MLF applications, SC High Performance Test Sockets are available for most handler set-ups and offer exceptional AC performance.
-
product
Pressure Generators
Calibration hand pumps serve as pressure generators for the testing, adjustment and calibration of mechanical and electronic pressure measuring instruments through comparative measurements. These hand pump calibrators can take place in the laboratory or workshop, or on site at the measuring point.
-
product
Ideal Remote Plasma Source For Oxygen-Based Processes
Rapid OX
Reduce recombination effects and extend the lifetime of oxygen radicals thanks to Rapid OX's removable quartz liner. When compared to anodized chambers, the resultant reactive species extended lifetime improves photoresist strip rates. And because the quartz liner is easily installed or removed by the operator, it decreases downtime and significantly lowers replacement costs.
-
product
Digital Insulation Tester
SK-3502
125V/250V/500V/1000V, Comparator Function., Data Memory (up to 100 data)., Low Resistance Measurement., AC/DC Voltage Measurement., Enhanced Safety Functions.
-
product
Partial Discharge Inductor
Tracy
BAUR Prüf- und Messtechnik GmbH
Cable testing and diagnostics with the BAUR tracy. The BAUR tracy partial discharge inductor induces a signal at the apparent fault location in the cable from outside. In combination with any PD measurement system, e.g., PHG TD/PD, the induced signal can be located and compared with the result of the partial discharge pre-location. The partial discharge location can thus be determined precisely.* Portable, battery-operated signal coupling device* Suitable for cables and cable accessories* Inductive signal coupling* Aviods costly, unnecessary replacements of PD-free cable accessories
-
product
Recheck-web Chrome extension
Using the Chrome extension is extremely easy. Just click on the retest logo to open a popup where you can either create a new Golden Master or compare the current website to an existing one.
-
product
Mass Comparators
Comparators from 0.1 g to 6000 kg. M_one and M_10 Vacuum Mass Comparators, Automated Mass Comparators, Robotic Mass Comparators, Systems for Volume, Density & Magnetism, Manual Mass Comparators.
-
product
Advanced 2-Axis Servo & Stepper Motion Controller
PCI-8102
PCI-8102 is an advanced stepper/servo motion controller to meet high performance/cost ratio request. Compared with PCI-8132/PCI-8134, PCI-8102 mainly offers three features: Software security check for users' software, card ID setting and circular interpolation control. Besides, PCI-8102 also provides users many additional features with cost-effective way. For details, please refer to the user manual.
-
product
Cable Testers
CableJoG 256
The CableJoG 256 can test up to 256 individual connections of all manufacturers of connectors. This simple test instrument stores up to 12 separate connection configurations. Each cable that is tested is compared with the configuration stored in its memory to produce a pass/fail indication of each pin connection
-
product
Crimp Force Monitor
638007950
The crimp force monitor measures the force signature of a crimped terminal and compares it to a reference crimp. Depending on the limits programmed, the measurement will pass, fail, or be suspect.
-
product
Low Pressure Cylinder Leak Tester
CLT4PB
Tests leakage at 35psi compared to 100psi in current leakage tester. Lower pressure prevents smaller bore cylinders from moving as they might under 100psi. Works well on small engines found in recreational, marine and other applications.
-
product
CTDs: Profiling
Profiling CTDs make continuous measurements as they travel through water. When lowered over the side of a ship or integrated with an autonomous vehicle, they map a vertical column of water's characteristics. Compared to moored CTDs, profiling CTDs account for dynamic errors introduced by moving through water and sample rapidly to generate a high-resolution dataset over a short period of time. Sea-Bird Scientific profiling CTDs are:*Designed to perform under unique dynamic conditions found on moving platforms.*Pumped and ducted for constant flow to match temperature and conductivity response.*Plumbed so measurements are made on the same sample of water with a predictable delay and predictable flow effects.*Built with a rugged design for shipboard and autonomous deployments.
-
product
Wire/Cable Harness Tester
PANTHER 4HT
Qmax Test Technologies Pvt. Ltd.
The Panther 4HT Wire \ Cable Harness tester is designed for Automotive and Semiconductor industry to apply in testing of wire harnesses, that needs testing during production with whole new fleet of features that make the task reliable, complete and fast. It uses innovative technology to test the impedance values. It can be interfaced to any type of fixtures as required. It uses the Learn and Compare technique for finding out opens or shorts in a harness. The learnt open / short combination from a Good Board is taken as reference and compared with the Board Under Test for any mismatch.
-
product
Characterization of Solar Cells
Paios
Paios performs a large variety of experiments in no time with one click. Get consistent and precise measurement data, directly compare your results in the measurement software and speed up your research.Increase your research speedCompare your devices directly in the softwareGet highly consistent dataThink about physics - Let Paios handle the rest
-
product
Active Dual Loop Antenna
KH30936
Beijing KeHuan Century EMC Technology Co,.LTD
KH30936 active dual loop antenna is used for adjusting, testing, measuring and other receivers. It has many advantages:1. The antenna coverage frequency is wide: 150KHz ~ 30MHz .2. The field strength value is measured according to the correction coefficient within the effective frequency range, which is convenient to use.3. The antenna power is supplied by the host, which is convenient for outdoor measurement.4. Compared with the single loop antenna, the advantage is to read the maximum value directly, which eliminates the tedious steps of rotating the antenna to find the maximum value and the interference of the human body to the signal.
-
product
Two Channel Phase and Amplitude Noise Analyzer
DCNTS -190
The DCNTS is a two channel Phase and Amplitude noise analyzer. Its dual demodulator architecture allows the system to use cross-correlation to cancel its internal noise and limitation; it is like comparing the outputs of 2 systems and only display the similarities while rejecting differences. Its main extension is the Residual Noise measurement front-end which includes all necessary hardware to automatically measure residual noise on 2-ports devices either in RF frequencies or microwave. It could be a frequency multiplier or divider, an amplifier or any other phase coherent input to output device.
-
product
Digital to Resolver
HDR
Computer Conversions Corporation
The HDR Series are sub-miniature modules that are; size comparable, low cost alternatives to Hybrid type D-R and D-S converters. Because of their advanced modular design the HDRL series features short lead times that are neither limited to infrequent hybrid production cycles, long term parts allocation, minimum quantity purchases, or hybrid obsolescence related concerns.
-
product
High Voltage Snubber Capacitor
STP-01RAN/STP-01RFN/STP-01RFB
This series of capacitors is Plastic Enclosure, Dry construction design and doesn't have leakage problem when compared with traditional Metal Enclosure Oil impregnated capacitors.Handle Medium Frequency range, high surge current, RMS current and surge voltage with temperature up to +105CCapacitance : 0.1uF - 15uF ( can be customized )Voltage range : 1,200Vdc to 17,000Vdc / 350Vrms to 6,900VrmsRMS Current - Irms : up to 100Armspeak to peak pulse current - Ipp : up to 5,900AppTemperature ranges : +85C / +105C
-
product
Pressure Switches
Our Pressure Switches are; lightweight, miniature in size and low in cost compared to competitive products. At a rated loadyou can expect the pressure switches we supply to provide a fast, repeatable response for millions of cycles.
-
product
Test Strips
High-quality Hach chemistry in an easy-to-use test strip. Simply dip the strip into the sample and compare the color to the colors on the bottle to determine the reading. The test strips are accurate, portable and inexpensive. Applications include potable water, waste water, swimming pools and spas, industrial process applications and more. Available parameters include chlorine, nitrate and nitrite, water hardness, alkalinity, chloride, ammonium and more. Hach offers a high-quality 5-in-1 test strip that measures free chlorine, total chlorine, hardness, alkalinity, and pH—all in one strip.
-
product
Multi-Meter
Talon-Curve
A portable instrument that enables you to troubleshoot electronic equipment in a powered down state. Simply place the leads across a component and the meter will display a graph allowing you to identify the type and range of each component tested. A helpful capture feature allows you to quickly compare the current component in test to a like component that was previously tested.
-
product
MTF Measurement Station
ImageMaster PRO 10
As a result of various improvements the ImageMaster® PRO 10 enables customers to significantally increase their yield. It is the fastest and most accurate MTF measurement system on the market for qualifying mobile phone lenses and other miniature lenses. Besides the new software architecture and functions, the more precise mechanical components lead to best performance in accuracy, reliability and measurement speed. Faster MTF algorithms reduce the test cycle time so that an outstanding throughput is achieved. The ImageMaster® PRO 10 features a 15% increased productivity compared to the ImageMaster® PRO 9.The new ImageMaster® PRO 10 also provides additional measurement functions. For example, measurements at different frequencies and RGB measurements can be performed to determine chromatic aberration. An upgrade of four additional cameras allows the measurement of relative illumination for testing the homogeneous illumination of lenses in the field.
-
product
Circuit Breaker Analyzer
CBAnalyzer
Simple operation requiring minimal trainingVery portable - it's a laptop or tablet pc running our Windows software programNo modification of the circuit breaker is requiredNo electrical connections are requiredRemoval of the circuit breaker from its mounting or cubicle is not requiredTesting can be performed during routine switchingData is easily transmitted over the internet to the users account where it is analyzed and compared with a known good profile (KGP) for that type of circuit breaker to determine: • Overall mechanical condition • Confirm maintenance intervals and lubrication • First trip testing data for arc flash compliance • Arc flash study validation checksPerform detailed analysis and store maintenance records using CBAnalyzer suite softwareAccess to the CBAnalyzer Account Manager which: • is where user accounts are created and each user's role is designated • provides access to your equipment database and test data archives • is where tests are synced • is where your equipment data is entered and stored • is required to use the CBAnalyzer software program
-
product
USB Instruments
Streamline Series
The Keysight Streamline Series consists of compact, faceless, USB instruments. With the same applications and accuracy as comparable benchtop instruments, the series is the perfect compact USB option. It is portable, easy to use, and there is zero compromise in performance. Series is comprised of compact USB instruments: vector network analyzers (VNAs), oscilloscopes and an arbitrary waveform generator (AWG).
-
product
Linear Array
Linear array sensors consist of a linear array of integrating photosensing pixels which measure incident light over a user-defined exposure time and generate a voltage or digital output which represents the light exposure at each pixel. The sensors are available in a variety of lengths and pixel resolutions. The analog output may be directly interfaced to an ADC for digital processing or for comparing black/white thresholds. Applications include contact image sensing, optical character recognition, edge detection, and object measurement in products such as copiers, document scanners and spectroscopy.
-
product
Network Analyzer, Lan Tester, LED
72-6706
The Tenma Multi-Network and Modular Cable Tester easily reads the correct pin configuration of 10Base-T cable (Category 5, 5e and 6), 10Base-2 cable (coax), RJ-45 and RJ-11 modular cables, 356A, TIA-568A/568B and Token Ring cable by comparing transmitting end to the corresponding receiving end
-
product
Bulk Acoustic Wave Technology
BAW
Macom Technology Solutions Holdings Inc.
MACOM’s BAW product portfolio is ideal for high performance Industrial, Aerospace, Defense, and Communications applications that require critical frequency filtering. Our high-performance RF filters enable our customers manage signal integrity in the 1 to 6 GHz frequency range. Bulk Acoustic Wave Resonators consist of two metal electrodes above and below a layer of a piezoelectric material. The piezoelectric material converts an electrical signal to a mechanical signal and vice versa. The metal electrodes provide the connections to/from the piezo material. The frequency at which resonance occurs depends on the thickness of the combined metal-piezo-metal stack. Advances in thin-film piezoelectric fabrication have enabled BAW resonators to meet RF filtering challenges up to 6000 MHz using standard MEMS fabrication process. High-performance BAW resonators-based RF filters are made of piezoelectric material having high Q-factor (>3000) and high coupling coefficient. Currently, no competitive technology provides the same high performance for RF filter applications when compared to BAW resonator-based RF filter up to 6000 MHz for the same size and cost.
