-
product
Universal, Production In-System Programmer
FlashRunner Series
FlashRunner is a universal, production In-System Programmer.It is the result of many years of experience in developing programmingand debugging solutions for microcontrollers.
-
product
Super Fast Stand-Alone ISP Programmer
848Pro2
The Dataman 848Pro2 is a super fast stand-alone gang programmer with eight independent 48-pin ZIF sockets, ISP capabilities and internal control PC driven by Windows Embedded 8.1 Industry Pro • Stand-alone operation with touch screen control • Internal control PC driven by Windows Embedded 8.1 Industry Pro • Up to 75% faster programming of high-capacity memory devices • Over 105,000 devices supported with new devices added monthly • Independent modules supporting concurrent programming • Intelligent pin drivers operate down to 1.8V so you'll be ready to program the full range of advanced low-voltage devices • Full ISP capabilities including JTAG compatibility • Comprehensive 3 years parts and labor warranty • Free life-time software updates
-
product
PXIe 8 Bit High Speed Digitizer 5 GS/s on 1 Channel, 2.5 GS/s on 2 Channels, 1.25 GS/s on 4 Channels, 1.5 GHz Bandwidth
M4X.2234-X4
The 9 models of the M4x.22xx-x4 Express series are designed for the high speed data acquisition. Each of the input channels has its own A/D converter and its own programmable input amplifier. This allows the recording of signals simultaneously on all channels without any phase delay between them. The extremely large on-board memory allows long time recording even with the highest sampling rates.
-
product
PXI-6514, 64-Channel, ±30 VDC, 32 Sink/Source Inputs, 32 Source Outputs, Bank-Isolated PXI Digital I/O Module
778965-01
64-Channel, ±30 VDC, 32 Sink/Source Inputs, 32 Source Outputs, Bank-Isolated PXI Digital I/O Module—The PXI‑6514 is an industrial digital I/O interface with eight banks of isolated channels. With programmable power-up states, you can configure the initial output states in software to ensure safe operation when connected to industrial actuators. If a computer or application fault occurs, the PXI‑6514 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions. Programmable input filters eliminate glitches/spikes and provide debouncing for digital switches/relays through a software-selectable digital filter.
-
product
PCI High Density Pecision Resistor Card, 9-Channel, 2Ω To 62.1Ω
50-298-111
The 50-298-111 is a high density programmable resistor card with 9 channels which can be set between 2Ω and 62.1Ω with 0.25Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
ISC-1782, 2 MP, 1.58 GHz Processor, Monochrome/Color Smart Camera
785148-01
The ISC‑1782 is a high-performance smart camera for machine vision and is powered by a 1.58 GHz dual-core Intel Celeron processor. The combination of the onboard processor with a CMOS image sensor provides an easily distributed all-in-one system. In addition to high-performance image acquisition and processing, you can use built-in digital I/O and industrial communication options for dynamic, real-time communication and integration with industrial automation devices including programmable logic controllers (PLCs), human machine interfaces (HMIs), robotics, sensors, and industrial machinery. You can configure NI Smart Cameras with the included Vision Builder for Automated Inspection (AI) software or program the camera with the LabVIEW Real‑Time Module and the Vision Development Module.
-
product
PXI High Density Precision Resistor Module, 9-Channel, 3Ω to 6.97kΩ
40-298-030
The 40-298-030 is a high density programmable resistor module with 9 channels which can be set between 3Ω and 6.97kΩ with 0.125Ω resolution The 40-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
product
Digital Superficial Rockwell Hardness Tester Tallboy
900-349
This digital Superficial Rockwell hardness tester with fully automated load/unload procedures affords highly sensitive and accurate readings. Micro computer controlled with USB output to built-in mini printer or PC. The 900-349 digital superficial Rockwell hardness tester offers programmable scale conversions, dwell times, statistical capabilities and test counter. Capable of testing in all of the superficial Rockwell® scales.
-
product
PXI Resistor Module 4-Channel 1R to 127R
40-293-012
The 40-293 is a Programmable Resistor module with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
GPIB-USB-HS+ , USB, Analyzer Software Included, IEEE 488 GPIB Instrument Control Device
783370-01
USB, Analyzer Software Included, IEEE 488 GPIB Instrument Control Device - The GPIB‑USB‑HS+ is an IEEE 488 controller and portable analyzer device for computers with USB slots. You can use this device to integrate an instrument into your system using GPIB as well as to troubleshoot and solve GPIB hardware and software problems. The GPIB‑USB‑HS+ achieves maximum IEEE 488.2 performance. With no GPIB cable required for instrument connection, you can use the Hi‑Speed USB port to control up to 14 programmable GPIB instruments. The improved design allows for size compatibility with almost every instrument, adds analyzer functionality, and reduces the overhead to generate faster turnaround times in your application. The device includes a license for the NI‑488.2 driver software, providing maximum reliability for connecting to third-party instruments with GPIB.
-
product
PXI Resistor Module 2-Channel 1.5R to 2.04k with SPDT
40-293-122
The 40-293 is a Programmable Resistor module with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
High-resolution Spectrometer
HR2000+
The HR2000+ Spectrometer integrates a high-resolution optical bench, a powerful 2-MHz analog-to-digital (A/D) converter, programmable electronics, a 2048-element CCD-array detector, and a high-speed USB 2.0 port. This innovative combination produces and extremely fast spectrometer and provides resolution to 0.035 nm (FWHM).
-
product
Autoranging System DC Power Supply, 750 V, 20 A, 5000 W, 208 VAC
N8924A
The Keysight N8900 Series provides 5 kW, 10 kW, and 15 kW autoranging, single-output programmable DC power for ATE applications that require just the right amount of performance at just the right price. The N8900 Series power supplies' autoranging output characteristic enables unprecedented flexibility by offering a wide range of voltage and current combinations at full power. Power supplies with "rectangular," or traditional, output characteristics provide full power at only one voltage and current combination. Just one N8900 does the job of multiple power supplies. It's like having many power supplies in one!
-
product
GPIB-USB-HS+ , USB, Analyzer Software Included, IEEE 488 GPIB Instrument Control Device
783368-01
USB, Analyzer Software Included, IEEE 488 GPIB Instrument Control Device - The GPIB‑USB‑HS+ is an IEEE 488 controller and portable analyzer device for computers with USB slots. You can use this device to integrate an instrument into your system using GPIB as well as to troubleshoot and solve GPIB hardware and software problems. The GPIB‑USB‑HS+ achieves maximum IEEE 488.2 performance. With no GPIB cable required for instrument connection, you can use the Hi‑Speed USB port to control up to 14 programmable GPIB instruments. The improved design allows for size compatibility with almost every instrument, adds analyzer functionality, and reduces the overhead to generate faster turnaround times in your application. The device includes a license for the NI‑488.2 driver software, providing maximum reliability for connecting to third-party instruments with GPIB.
-
product
PXI Programmable Resistor Card 4-Channel 2 Ohm to 255 Ohm - SPST
40-294-113
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
AC Power Source
6500 series
The global AC power testing requirements demand more sophisticated AC Power Source that is capable of simulating a wide variety of AC line conditions, harmonic waveforms, accurate power measurement and analysis. The Chroma 6500 series Programmable AC Power Source delivers the right solution to simulate all kinds of normal/abnormal input conditions and measure the critical characteristics of the product under test. It can be used for R&D design characterization, production testing, and QA verification of commercial, industrial, and aerospace electronic products. The Chroma 6500 series delivers maximum rated power for any output voltage up to 300 Vac, and at any frequency between 15Hz to 2000Hz. It is suitable for commercial applications (47-63Hz); for avionics,marine, military applications at 400Hz or higher frequency; or for electrical motor, air-conditioner test applications at 20Hz. All models generate very clean sine or square waveforms output with typical distortion less than 0.5%. The Chroma 6500 series has built-in Direct Digital Synthesis (DDS) Waveform Generator to provide user programmable high precision waveform. For testing products under AC line distortion conditions, clipped sinewave can be generated with 0% to 43% distortion and amplitude from 0% to 100%. It also can simulate all kinds of power line disturbances such as cycle dropout, transient spike, brown out, phase angle, voltage and frequency ramp up (ramp down), etc.. Up to 30 harmonic waveforms are factory installed, and testing for compliance to AC line harmonic immunity standards can be easily achieved in the field.
-
product
DC Power Supply
62000P series
Chroma's new 62000P Series of programmable DC power supplies offer many unique advantages for ATE integration and testing. These advantage include a constant power operating envelope, precision readback of output current and voltage, output trigger signals as well as the ability to create complex DC transients waveforms to test device behavior to spikes, drops, and other voltage deviations.Designed for automated testing DC-DC converters and similar products, the 62000P sets a new standard for high accuracy programmable DC supplies. The 62000P Series includes 12 different models ranging from 600W to 5000W, up to 120A and up to 600V. Due to their constant power operating envelope a single instrument can provide both high voltage/low current AND low voltage/high current thereby reducing the number of supplies needed in typical ATE applications.
-
product
PXI Resistor Module Dual 16 Bit
40-290-021
The 40-290 Series Programmable Resistor Modules comprise a Dual 16-bit or Quad 8-bit resistor chain together with 16 optional SPDT Reed Relays. Connections are made via a front panel SCSI 2 type 68 pin male connector. Programmable resistors may be connected together either in series or in parallel to form many types of configuration.
-
product
PXI/PXIe High Density Precision Resistor Module
42-297A-145
The 40-297A-145 (PXI) and the 42-297A-145 (PXIe) are 3-channel programmable resistors with a range of 2.5 Ω to 2.97 MΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
product
PXI/PXIe High Density Precision Resistor Module
42-297A-123
The 40-297A-123 (PXI) and the 42-297A-123 (PXIe) are 4-channel programmable resistors with a range of 1.5 Ω to 3.55 kΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
product
150~300W DC Electronic Loads
JT631 Series
Nanjing Jartul Electronic Co., Ltd
JT631 series electronic load is functioned with 500KHz high-speed synchronous sampling, DSP technology, powerful dynamic test and multi-aspect intelligence analysis. All these are fully integrated into auotmatic test function, which makes JT631 series load very suitable for testing power supply when produced in large quantity. Besides, JT631 series load also possesses the features of current rising slew rate programmable, high-speed dynamic loading and programmable list function, which makes JT631 series load satisfing most of R&D requirements. Moreover, JT631 series load’s special parallel operation method can satisfy the synchronous loading requirements of multi-channels output power supply and satisfy single-channel output power supply requirement for big power.
-
product
Single Loop Controller
1460
he 1460 has been designed to provide immediate visibility to the operator. At a glance, the programmable displays will show you the measured variable, the set point and the parameter being edited, the number of cycles or time remaining, the recipe name and number and also whether the cycle is in a ramp or soak mode
-
product
RISC-V Processor IP Core Evaluation Kit
The EMSA5 demo platform is an ideal tool for evaluating the RISC-V processor IP core EMSA5. It contains an Artix®-7 35T FPGA Arty evaluation board with implemented EMSA5-IP core. Thanks to the included peripherals and expansion interfaces, the kit is ideal for numerous applications. The kit is JTAG programmable and includes Quad SPI Flash, a JTAG port, 10/100 Mb/s Ethernet and a USB-UART bridge, four Pmod connectors and an Arduino Shield expansion connector.
-
product
Test Automation System for Engine Testing
STARS Engine
With a wide range of user-friendly features, STARS Engine can run the most complex of tests with a simple press of a button making your test operation effective and efficient and above all, reliable. STARS provides all the features you need to run a wide range of Engine Test Programmes from simple manual testing to dynamic automatic tests, all from a single, simple to use user interface. STARS is designed to be run in either stand-alone operation for a single test stand or as a cluster of systems to allow a test field to be run more efficiently. In both cases the user works in the same way and uses the same interface.
-
product
24 TTL Channels, Enhanced, Programmable I/O
TL2
Function module TL2 provides 24 channels of TTL/CMOS transceiver functionality as either inputs or outputs. The transistor-transistor logic (TTL) employs transmitters with multiple emitters in gates having more than one input. TTL offers high switching speed and relative immunity to noisy systems. CMOS sensors provide image sensing technology by converting light waves into signals that are small bursts of current. These waves can be light or other electromagnetic radiation.
-
product
Digital Multifunction
Contrel Elettronica s.r.l. Company
The DIN rail and front panel multimeters are ideal for installation in secondary distribution panels. Measurement of the main electrical parameters. Measurement of active, reactive and apparent energy. Modbus RTU, Modbus TCP, Profibus, M-Bus protocol. Digital outputs programmable as alarms or pulses.
-
product
PCI Programmable Resistor Card 2-Channel 3 Ohm To 65.5k Ohm - SPST
50-294-133
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
Amplified Torque & Load Cell Indicator
9834
For use with amplified load cells and rotary torque sensors. Features 120 readings per second, programmable +/-10V or 4-20mA analog output, peak and valley monitoring, RS232. Packaged in an aluminum 1/8 DIN, panel mountable enclosure with a plug-in AC power cord. Sensor connection via 9-pin connector.
-
product
Xhorse AM29Fxxx
For the programmer vvdi prog. To the eyes and programming of flash memory: SOP48, TSOP48 with reversed pinout, TSOP48 with standard pinout.
-
product
Programmable DC Power Supply
KM-LPP-3030T
Kusam Electrical Industries Limited
KM-LPP-3030T provides a higher stability in terms of traditional Programmable DC Power Supply. KM-LPP-3030T, linear programmable DC Power Supply support USB PC-Link and two completely separate power outputs. With the various characteristics, KM-LPP-3030T is the best choice of power supplies for engineers. With the functions of the power supply of KM-LPP-3030T, it provides two completely separate power output which is able for series or parallel connection; other than the common power supplies on the market of positive / ground / negative output. In addition, KM-LPP-3030T supports low-voltage digital circuits, also it is able to switch voltage among 1.8V~5.0V. With its characteristics of stability and high - speed reaction, KM-LPP-3030T provides high quality at a very economical price.
